Muh amin
Balai Pengkajian Teknologi Pertanian Sulawesi Tengah

Published : 2 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 2 Documents
Search

PENGGUNAAN ALAT PENGERING UNTUK MENSUPLAY BAHAN BAKU PRODUKSI KRIPIK JAGUNG DI GROBOGAN Amin, Muh; Subri, Muhammad
PROSIDING SEMINAR NASIONAL & INTERNASIONAL 2017: PROSIDING IMPLEMENTASI PENELITIAN PADA PENGABDIAN MENUJU MASYARAKAT MANDIRI BERKEMAJUAN
Publisher : Universitas Muhammadiyah Semarang

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (269.465 KB)

Abstract

Abstrak. Telah berhasil dilakukan pengabdian pada masyarakat penyewa lahan Perum Perhutani Grobogan yang tengah mengembangkan usahanya dibidang pembuatan kripik jagung. Pengabdian ini berawal dari produsen kripik jagung yang mengalami kelangkaan bahan baku (jagung) pada musim kemarau karena kebanyakan penanam jagung dilakukan di ladang tanpa ada saluran irigasi. Untuk mengatasi hal tersebut, dibuatlah alat pengering jagung tipe box dengan bahan bakar tongkol jagung. Alat pengering jagung dengan kapasitas 1 ton dalam setiap operasi ini bekerja dengan sistem tekan dengan menggunakan kipas berukuran 0,5 HP. Dengan proses pemanasan yang dipergunakan adalah dengan cara tidak langsung alat pengering yang dibuat mampu mengeringkan jagung dengan lama waktu pengeringan selama 10 jam dengan suhu pengeringan 50oC selama 30 jam diperoleh kadar air 15% b.k dari 32,3% b.k. Hasil pengeringan jagung ini sudah memenuhi persyaratan mutu jagung menurut SNI 01-3920-1995 pada kualitas mutu ke III yaitu maksimal 15 % kadar air.Kata Kunci: Alat Pengering Jagung, Tongkol Jagung, Jagung, Bahan Baku Kripik
EFEKTIFITAS PEMANFAATAN SERBUK BATU ALAM BERSILIKA, SILANE SEBAGAI PENGISI BAHAN ISOLASI RESIN EPOKSI DENGAN KOMPATIBILISER POLYETHYLENE UNTUK ISOLATOR LISTRIK Toni, Moh; Amin, Muh
MEDIA ELEKTRIKA Vol 13, No 1 (2020): MEDIA ELEKTRIKA
Publisher : PSTE UNIMUS

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (469.98 KB) | DOI: 10.26714/me.13.1.2020.33-42

Abstract

Insulation materials that commonly used in air insulation, which, is operated at high voltage, are the porcelain, glass, and polymer materials. One of the insulating polymer materials that are used is epoxy resin because it has several advantages compared to that. However, this insulation material has a degradation of the surface due to environmental and cause insulation coated with dirt and chemicals in the long time.  This research was conducted on resin epoxy by comparison of MPDA, DGEBA, and filler (stone and silane) with a percentage value of 10%; 20%; 30%; 40% and 50%, sample size 120 x 50mm. Poly Ethylene is mixed as a compatibilzer of composite materials.Research was done in laboratory according to standard IEC 587: 1984. In this study, the effect of variation in stoichiometry to the hydrophobic contact angle value, leakage current waveforms, and surface degradation caused by erosion and tracking processes and tracking time were analyzed. From the results of the research, it was obtained that the epoxy resin that was used in this research are categorized as partially wetted. The increase concentration of silane and silica stone as filler caused the increase in contact angle which meant the increase in surface insulation resistance, so that leakage currents flew on the surface not easily and slow down the aging or the degradation decreasing on the surface of insulating material. The concentration value of comapatibilizer material that had the optimal performance was 4%.