Garuda - Garba Rujukan Digital

p-Index From 2019 - 2024

0.61

P-Index

This Author published in this journals

All Journal International Journal of Electrical and Computer Engineering Logic : Jurnal Rancang Bangun dan Teknologi Aptekmas : Jurnal Pengabdian Kepada Masyarakat

Rusdi Nur

Politeknik Negeri Ujung Pandang

Author-ID : 2382064

Religion Aerospace Engineering Agriculture, Biological Sciences & Forestry Arts Humanities Astronomy Automotive Engineering Biochemistry, Genetics & Molecular Biology Chemical Engineering, Chemistry & Bioengineering Chemistry Civil Engineering, Building, Construction & Architecture Computer Science & IT Control & Systems Engineering Decision Sciences, Operations Research & Management Dentistry Earth & Planetary Sciences Economics, Econometrics & Finance Education Electrical & Electronics Engineering Energy Engineering Environmental Science Health Professions Immunology & microbiology Industrial & Manufacturing Engineering Languange, Linguistic, Communication & Media Law, Crime, Criminology & Criminal Justice Library & Information Science Materials Science & Nanotechnology Mathematics Mechanical Engineering Medicine & Pharmacology Neuroscience Nursing Physics Public Health Social Sciences Transportation Veterinary Other

Published : 3 Documents Claim Missing Document

Claim Missing Document

Articles

Algorithm for Fault Location and Classification on Parallel Transmission Line using Wavelet based on Clarke’s Transformation Makmur Saini; A. A. Mohd Zin; M. W. Mustafa; A. R. Sultan; Rusdi Nur
International Journal of Electrical and Computer Engineering (IJECE) Vol 8, No 2: April 2018
Publisher : Institute of Advanced Engineering and Science

This paper proposed a new algorithm for fault location and classification using wavelet based on Clarke’s transformation to obtain the fault current. This novel method of fault current approach is studied by comparing the use of the glide path of the fault voltage. The current alpha and beta (Current Mode) were used to transform the signal using discrete wavelet transform (DWT). The fault location was determined by using the Clarke’s transformation, and then turned into a wavelet, which was very precise and thorough. The most accurate was the mother wavelet Db4 which had the fastest time and smallest error detection when compared with the other wavelet mothers. In this study, the Clarke’s transformation is also compared with the Karenbauer’s, which has produced results with similar error percentage. The simulation results using PSCAD / EMTDC software showed that the proposed algorithm could distinguish internal and external faults to get the current signal in the transformation of a signal fault.

PENINGKATAN USAHA DAN PENDAMPINGAN PIRT SERTA SERTIFIKASI HALAL ABON IKAN WALASOJI Rusdi Nur; Muhammad Arsyad; Sirajuddin Omsa
Aptekmas Jurnal Pengabdian pada Masyarakat Vol 5 No 1 (2022): APTEKMAS Volume 5 Nomor 1 2022
Publisher : Politeknik Negeri Sriwijaya

The Walasoji Shredded Fish (AIW) Business Community was located in Rappang Village, Panca Rijang District, Sidenreng Rappang Regency, South Sulawesi, started its activities in 2012. The partner community is a home industry, initially having around eight members, but now there are only three people. In the shredded production process, partners still use traditional tools, partners cannot determine the exact profit, the packaging of shredded products is still simple without a brand, without a health department permit number, and without a halal certificate from MUI. The problems faced by partners are: how to improve the quality and production capacity, how to know the profit for sure, how to increase the market share of shredded walasoji fish. Based on the problems above, the solution is to improve production methods and processes using machines, provide training and counseling on management, as well as a simple accounting bookkeeping system, assist in branding and packaging equipment, assist in obtaining permits from the health department, and MUI halal certificates. Through this PKM, it is hoped that the capacity and quality of AIW produced by partners will increase, and can be marketed through markets, shops, supermarkets and supermarkets. The methods that will be applied are assistance with production equipment, and packaging, training and counseling on management, and a simple accounting system, assisting in obtaining permits from the health department, and MUI halal certificates. The output targets to be achieved in this activity are scientific publications in national journals or proceedings of national seminars, and published in print or online mass media. With the publication, it is targeted that AIW, which is only known in Rappang, can be widely known, both regionally and nationally after this PKM is implemented.

Designing and Manufacturing the Press Tool of Air Bending V Brake Rusdi Nur; Muhammad Arsyad Suyuti; Muhammad Iswar
Logic : Jurnal Rancang Bangun dan Teknologi Vol 19 No 3 (2019): November
Publisher : Pusat Penelitian dan Pengabdian kepada Masyarakat (P3M) Politeknik Negeri Bali

Nowadays, the metal forming process in the welding machinery and machinery industry is developing very rapidly, especially in the bending process. The buckling process is a metal formation which generally uses sheet plates or rods from both ferrous and non-ferrous metals by bending, which in the bending process will cause a stretching or stretching on the neutral axis of the field along the bending area and producing a straight bending line. Appropriate technology machines have been widely used to increase productivity, efficiency, and effectiveness in the production process for community efforts. One of the appropriate technologies that can be applied in buckling is a tool equipped with a press tool. Press tool is one type of tool for the formation, cutting and bending of products from the base material of sheet plates whose operation uses a press machine. In this study, a V brake bending tool has been produced which has a capacity that is bending line length 300 mm, bending width 33 mm, spring height 110 mm, free step distance 19 mm, spring load received 263,820 N and material capacity that can be bent is a thickness of 3 mm, the punch angle used is 85⁰ with a punch radius used which is 1.5 mm while the die angle is 85⁰

Co-Authors A. A. Mohd Zin Ahamad Rizal Sultan Henny Pasandang Nari M. Iqbal Mukhsen M. W. Mustafa Mahadir Sirman Makmur Saini Muhammad Arsyad Muhammad Arsyad Suyuti Muhammad Iswar Sirajuddin Omsa

Title

Found 3 Documents
Search

Abstract

Abstract

Abstract

Title Search

Found 3 Documents Search

Abstract

Abstract

Abstract

Title

Found 3 Documents
Search