S. M. A. Motakabber
International Islamic University Malaysia

Published : 15 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 15 Documents
Search

Design of an Interdigital Structure Planar Bandpass Filter for UWB Frequency S. M. A. Motakabber; M. N. Haidari
International Journal of Electrical and Computer Engineering (IJECE) Vol 8, No 3: June 2018
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (576.189 KB) | DOI: 10.11591/ijece.v8i3.pp1654-1658

Abstract

A new topology of miniaturized interdigital structuremicrostrip planar bandpass filter for Ultra-Wideband (UWB) frequency has been discussed in this paper. The proposed design and its simulation have been carried out by using an electromagnetic simulation software named CST microwave studio. The Taconic TLX-8 microwave substrate has been used in this research. The experimental result and analysis have been performed by using the microwave vector network analyzer. The experimental result showed that the -10dB bandwidth of the filter is 7.5GHz. The lower and upper corner frequencies of the filter have been achieved at 3.1GHz and 10.6GHz respectively. At the center frequency of 6.85GHz, the -1dB insertion loss and the -7dB return losshave been observed. The simulated and experimental results are well agreed with a compact size filter of 19×21×0.5mm3.
A novel bio-inspired routing algorithm based on ACO for WSNs Afsah Sharmin; F. Anwar; S. M. A. Motakabber
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1030.413 KB) | DOI: 10.11591/eei.v8i2.1492

Abstract

The methods to achieve efficient routing in energy constrained wireless sensor networks (WSNs) is a fundamental issue in networking research. A novel approach of ant colony optimization (ACO) algorithm for discovering the optimum route for information transmission in the WSNs is proposed here for optimization and enhancement. The issue of path selection to reach the nodes and vital correspondence parameters, for example, the versatility of nodes, their constrained vitality, the node residual energy and route length are considered since the communications parameters and imperatives must be taken into account by the imperative systems that mediate in the correspondence procedure, and the focal points of the subterranean insect framework have been utilized furthermore. Utilizing the novel technique and considering both the node mobility and the existing energy of the nodes, an optimal route and best cost from the originating node to the target node can be detected. The proposed algorithm has been simulated and verified using MATLAB and the simulation results demonstrate that new ACO based algorithm achieved improved performance, about 30% improvement compared with the traditional ACO algorithm, and faster convergence to determine the best cost route, and recorded an improvement in the energy consumption of the nodes per transmission.
Microstrip patch antenna with defected ground structure for biomedical application Md. Shazzadul Islam; Muhammad I. Ibrahimy; S. M. A. Motakabber; A. K. M. Zakir Hossain; S. M. Kayser Azam
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1626.281 KB) | DOI: 10.11591/eei.v8i2.1495

Abstract

Proper narrowband antenna design for wearable devices in the biomedical application is a significant field of research interest. In this work, defected ground structure-based microstrip patch antenna has been proposed that can work for narrowband applications. The proposed antenna works exactly for a single channel of ISM band. The resonant frequency of the antenna is 2.45 GHz with a return loss of around -30 dB. The -10dB impedance bandwidth of the antenna is 20 MHz (2.442-2.462 GHz), which is the bandwidth of channel 9 in ISM band. The antenna has achieved a high gain of 7.04 dBi with an increase of 17.63% antenna efficiency in terms of realized gain by using defected ground structure. Three linear vector arrays of arrangement 1 2, 1 4 and 1 8 have been designed to validate the proposed antenna performances as an array. The proposed antenna is light weighted, low cost, easy to fabricate and with better performances that makes it suitable for biomedical WLAN applications.
A miniaturized hairpin resonator for the high selectivity of WLAN bandwidth S. M. Kayser Azam; Muhammad I. Ibrahimy; S. M. A. Motakabber; A. K. M. Zakir Hossain; Md. Shazzadul Islam
Bulletin of Electrical Engineering and Informatics Vol 8, No 3: September 2019
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (708.103 KB) | DOI: 10.11591/eei.v8i3.1496

Abstract

In this article, a miniaturized hairpin resonator has been presented to introduce the high selectivity of Wireless Local Area Network (WLAN) bandwidth. In the construction of the hairpin resonator, short-circuited comb-lines are electrically coupled with the two longer edges of a rectangular-shaped loop. The hairpin resonator has been designed and fabricated with the Taconic TLX-8 substrate with a center-frequency at 2.45 GHz. The resonator exhibits a second order quasi-Chebyshev bandpass response. A low insertion loss has been found as -0.36 dB with a minimum return loss as -36.71 dB. The filtering dimension of this hairpin resonator occupies a small area of 166.82 mm2. This hairpin resonator is highly selective for the bandpass applications of the entire WLAN bandwidth.
Design and implementation of a series switching SPSI for PV cell to use in carrier based grid synchronous system Tawfikur Rahman; S. M. A. Motakabber; Muhammad I. Ibrahimy; A. H. M. Zahirul Alam
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1663.675 KB) | DOI: 10.11591/eei.v8i2.1507

Abstract

A carrier-based grid synchronous method is proposed to develop the system efficiency, phase and power quality of the inverter output waves. The operating principle of a single-phase phase synchronous inverter (SPSI) is introduced, with proper synchronous paid to the switching-frequency synchronizing voltage made by the interleaved process, as well as actual mitigation approaches. In the construction of the SPSI, input and output filters are electrically coupled with the two sides of an inverter. The inverter power electronic switches and other electrical components are operated by carrier-based grid synchronous controller (CBGSC) with PWM regulator. The SPSI is designed and implemented with the Toshiba 40WR21 IGBT, Digital Microcontroller pulse controller (DMPC) and 4N35 Optocoupler with a fundamental frequency of 50Hz. The other parameters are considered as load resistance, =11Ω, duty cycle, 85%, carrier frequency, 2.5kHz and input DC voltage, ± 340V. In addition, LCL lowpass grid filters are used to convert squire wave to sine wave with required phase and frequency. Finally, the simulated and experimental results obtained with a carrier-based grid synchronous SPSI experimental prototype are exposed for justification, showing the phase error of 55% improvement, reduced 11% of THD and the conversion efficiency of 97.02% highly predicted by the proposed design technique to improve the microgrid system.
Microstrip patch antenna with defected ground structure for biomedical application Md. Shazzadul Islam; Muhammad I. Ibrahimy; S. M. A. Motakabber; A. K. M. Zakir Hossain; S. M. Kayser Azam
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1626.281 KB) | DOI: 10.11591/eei.v8i2.1495

Abstract

Proper narrowband antenna design for wearable devices in the biomedical application is a significant field of research interest. In this work, defected ground structure-based microstrip patch antenna has been proposed that can work for narrowband applications. The proposed antenna works exactly for a single channel of ISM band. The resonant frequency of the antenna is 2.45 GHz with a return loss of around -30 dB. The -10dB impedance bandwidth of the antenna is 20 MHz (2.442-2.462 GHz), which is the bandwidth of channel 9 in ISM band. The antenna has achieved a high gain of 7.04 dBi with an increase of 17.63% antenna efficiency in terms of realized gain by using defected ground structure. Three linear vector arrays of arrangement 1 2, 1 4 and 1 8 have been designed to validate the proposed antenna performances as an array. The proposed antenna is light weighted, low cost, easy to fabricate and with better performances that makes it suitable for biomedical WLAN applications.
A novel bio-inspired routing algorithm based on ACO for WSNs Afsah Sharmin; F. Anwar; S. M. A. Motakabber
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1030.413 KB) | DOI: 10.11591/eei.v8i3.1492

Abstract

The methods to achieve efficient routing in energy constrained wireless sensor networks (WSNs) is a fundamental issue in networking research. A novel approach of ant colony optimization (ACO) algorithm for discovering the optimum route for information transmission in the WSNs is proposed here for optimization and enhancement. The issue of path selection to reach the nodes and vital correspondence parameters, for example, the versatility of nodes, their constrained vitality, the node residual energy and route length are considered since the communications parameters and imperatives must be taken into account by the imperative systems that mediate in the correspondence procedure, and the focal points of the subterranean insect framework have been utilized furthermore. Utilizing the novel technique and considering both the node mobility and the existing energy of the nodes, an optimal route and best cost from the originating node to the target node can be detected. The proposed algorithm has been simulated and verified using MATLAB and the simulation results demonstrate that new ACO based algorithm achieved improved performance, about 30% improvement compared with the traditional ACO algorithm, and faster convergence to determine the best cost route, and recorded an improvement in the energy consumption of the nodes per transmission.
A miniaturized hairpin resonator for the high selectivity of WLAN bandwidth S. M. Kayser Azam; Muhammad I. Ibrahimy; S. M. A. Motakabber; A. K. M. Zakir Hossain; Md. Shazzadul Islam
Bulletin of Electrical Engineering and Informatics Vol 8, No 3: September 2019
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (708.103 KB) | DOI: 10.11591/eei.v8i3.1496

Abstract

In this article, a miniaturized hairpin resonator has been presented to introduce the high selectivity of Wireless Local Area Network (WLAN) bandwidth. In the construction of the hairpin resonator, short-circuited comb-lines are electrically coupled with the two longer edges of a rectangular-shaped loop. The hairpin resonator has been designed and fabricated with the Taconic TLX-8 substrate with a center-frequency at 2.45 GHz. The resonator exhibits a second order quasi-Chebyshev bandpass response. A low insertion loss has been found as -0.36 dB with a minimum return loss as -36.71 dB. The filtering dimension of this hairpin resonator occupies a small area of 166.82 mm2. This hairpin resonator is highly selective for the bandpass applications of the entire WLAN bandwidth.
Design and implementation of a series switching SPSI for PV cell to use in carrier based grid synchronous system Tawfikur Rahman; S. M. A. Motakabber; Muhammad I. Ibrahimy; A. H. M. Zahirul Alam
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1663.675 KB) | DOI: 10.11591/eei.v8i2.1507

Abstract

A carrier-based grid synchronous method is proposed to develop the system efficiency, phase and power quality of the inverter output waves. The operating principle of a single-phase phase synchronous inverter (SPSI) is introduced, with proper synchronous paid to the switching-frequency synchronizing voltage made by the interleaved process, as well as actual mitigation approaches. In the construction of the SPSI, input and output filters are electrically coupled with the two sides of an inverter. The inverter power electronic switches and other electrical components are operated by carrier-based grid synchronous controller (CBGSC) with PWM regulator. The SPSI is designed and implemented with the Toshiba 40WR21 IGBT, Digital Microcontroller pulse controller (DMPC) and 4N35 Optocoupler with a fundamental frequency of 50Hz. The other parameters are considered as load resistance, =11Ω, duty cycle, 85%, carrier frequency, 2.5kHz and input DC voltage, ± 340V. In addition, LCL lowpass grid filters are used to convert squire wave to sine wave with required phase and frequency. Finally, the simulated and experimental results obtained with a carrier-based grid synchronous SPSI experimental prototype are exposed for justification, showing the phase error of 55% improvement, reduced 11% of THD and the conversion efficiency of 97.02% highly predicted by the proposed design technique to improve the microgrid system.
Design and implementation of a series switching SPSI for PV cell to use in carrier based grid synchronous system Tawfikur Rahman; S. M. A. Motakabber; Muhammad I. Ibrahimy; A. H. M. Zahirul Alam
Bulletin of Electrical Engineering and Informatics Vol 8, No 2: June 2019
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1663.675 KB) | DOI: 10.11591/eei.v8i2.1507

Abstract

A carrier-based grid synchronous method is proposed to develop the system efficiency, phase and power quality of the inverter output waves. The operating principle of a single-phase phase synchronous inverter (SPSI) is introduced, with proper synchronous paid to the switching-frequency synchronizing voltage made by the interleaved process, as well as actual mitigation approaches. In the construction of the SPSI, input and output filters are electrically coupled with the two sides of an inverter. The inverter power electronic switches and other electrical components are operated by carrier-based grid synchronous controller (CBGSC) with PWM regulator. The SPSI is designed and implemented with the Toshiba 40WR21 IGBT, Digital Microcontroller pulse controller (DMPC) and 4N35 Optocoupler with a fundamental frequency of 50Hz. The other parameters are considered as load resistance, =11Ω, duty cycle, 85%, carrier frequency, 2.5kHz and input DC voltage, ± 340V. In addition, LCL lowpass grid filters are used to convert squire wave to sine wave with required phase and frequency. Finally, the simulated and experimental results obtained with a carrier-based grid synchronous SPSI experimental prototype are exposed for justification, showing the phase error of 55% improvement, reduced 11% of THD and the conversion efficiency of 97.02% highly predicted by the proposed design technique to improve the microgrid system.