Article Per Year (5 Year)
p-Index From 2019 - 2024
1.259
P-Index
This Author published in this journals
All Journal International Journal of Power Electronics and Drive Systems (IJPEDS) Jurnal Ilmiah Teknik Elektro Komputer dan Informatika (JITEKI) Jurnal Pengabdian Pada Masyarakat Computer Science and Information Technologies Journal of Electrical, Electronic, Information, and Communication Technology (JEEICT) International Journal of Robotics and Control Systems Electrician : Jurnal Rekayasa dan Teknologi Elektro
Hari Maghfiroh
Universitas Sebelas Maret
Agriculture, Biological Sciences & Forestry Computer Science & IT Control & Systems Engineering Decision Sciences, Operations Research & Management Education Electrical & Electronics Engineering Engineering Other

Published : 7 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 7 Documents
Search

 1 
Constant current-fuzzy logic algorithm for lithium-ion battery charging Muhammad Nizam; Hari Maghfiroh; Azis Ubaidilah; Inayati Inayati; Feri Adriyanto
International Journal of Power Electronics and Drive Systems (IJPEDS) Vol 13, No 2: June 2022
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/ijpeds.v13.i2.pp926-937

Abstract

The lithium-ion (Li-ion) battery has a high demand because of its long cycle, reliability, high energy density, low toxic, low self-discharge rate, high power density, and high efficiency. However, lithium-ion batteries have sensitivity to over-charge, temperature, and charge discharge currents. The conventional battery charging system takes a very long time to charge which makes the battery temperature high. Therefore, a charger system that can maximize charging capacity, shorten charging time, and extend battery life is needed. In this study, a battery charging system was developed using the constant current–fuzzy (CC-fuzzy) control method. The aim is to get faster charging time and maintain battery life by limiting the battery charging temperature. The proposed charger system is dual mode which can be operated in both buck and boost mode. The experimental result shows that the proposed method is superior compared to the constant current constant voltage (CCCV) method in charging time. The CC-fuzzy method charging time is faster compared to the CCCV method by 25% and 12.5% in buck and boost modes, respectively. Whereas from the battery temperature, in buck mode, the proposed method has a lower temperature by 0.5 ⁰C and in the boost mode, each method has the same temperature.
Design of Smart Medical Mask Trash Can For Public Places Muhammad Dhafier Mu'afa; Refansyah Basu Dewa; Muhammad Raflie Pangestu; Muhammad Fiqih Al Faishal; Hari Maghfiroh
Journal of Electrical, Electronic, Information, and Communication Technology Vol 3, No 2 (2021): JOURNAL OF ELECTRICAL, ELECTRONIC, INFORMATION, AND COMMUNICATION TECHNOLOGY
Publisher : Universitas Sebelas Maret (UNS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.20961/jeeict.3.2.55186

Abstract

The Covid-19 pandemic mainly caused the sudden rise of medical mask waste. There are some steps that can be taken to reduce and manage the waste, including dissolving the mask so it cannot be use again, reduce the risk of disease transmission, and assist the workers in managing the waste of medical mask. Therefore, this paper proposes a device that can solve all the problem, which is the “Smart Medical Mask Trash Can”. This device can be used to dissolve and disinfect the mask, as well as manage the mask waste with an easy way in accordance with health protocol. The outcome show that this device can monitor the waste with an application program on a real time that can notify and organize a schedule for automatic disinfection. This tool is suitable to be placed in public places because of its high mobility and there is a lot of medical mask's waste.
Pengenalan Teknologi Kendaraan Listrik untuk Siswa Sekolah Menengah Pertama (SMP) Hari Maghfiroh; Feri Adriyanto; Augustinus Sujono; Joko Slamet Saputro; R Lulus Lambang GH
Jurnal Pengabdian Pada Masyarakat Vol 6 No 1 (2021)
Publisher : Universitas Mathla'ul Anwar Banten

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30653/002.202161.639

Abstract

INTRODUCTION TO ELECTRIC VEHICLE FOR JUNIOR HIGH SCHOOL STUDENTS. The purpose of this service program is to introduce junior high school students to electric vehicle technology. The material presented is basic material covering the meaning, benefits, and components of electric vehicles. The socialization was carried out via online due to the corona outbreak. The explanation is done with a short video consisting of a simple explanation as well as a demo of the components of a real electric vehicle with an electric bicycle. In addition, students are also given a short ebook on the material. To find out students' understanding, a short quiz about the material was given. The result is an average score of 83.9%, which indicates that the participants' level of understanding is quite good with the material presented. The sample of basic questions about electric vehicles showed that only 3.8% of students were wrong. In the final conclusion, students have gained knowledge about electric vehicles through socialization activities that have been carried out.
Design and Application of PLC-based Speed Control for DC Motor Using PID with Identification System and MATLAB Tuner Dodi Saputra; Alfian Ma'arif; Hari Maghfiroh; Phichitphon Chotikunnan; Safinta Nurindra Rahmadhia
International Journal of Robotics and Control Systems Vol 3, No 2 (2023)
Publisher : Association for Scientific Computing Electronics and Engineering (ASCEE)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.31763/ijrcs.v3i2.775

Abstract

Industries use numerous drives and actuators, including DC motors. Due to the wide-ranged and adjustable speed, DC motor is widely used in many industries. However, the DC motor is prone to external disturbance and parameter changes, causing its speed to be unstable. Thus, a DC motor requires an appropriate controller design to obtain a fast and stable speed with a small steady-state error. In this study, a controller was designed based on the PID control method, with the controller gains tuned by trial-and-error and MATLAB Tuner with an identification system. The proposed controller design was implemented using PLC OMRON CP1E NA20DRA in the hardware implementation. Each tuning method was repeated five times so that the system performances could be compared and improved. Based on hardware implementation results, the trial-error method gave acceptable results but had steady-state errors. On the other hand, the use of MATLAB Tuner provided fast system responses with no steady-state error but still had oscillations with high overshoot during the transition. Therefore, the PID controller gains acquired from MATLAB Tuner must be tuned finely to get better system responses.
Caring jacket: health monitoring jacket integrated with the internet of things for COVID-19 patients Hari Maghfiroh; Daru Kusumastuti; Rebbeka Siswandina Sari; Muhammad Hammam Al-Choiri; Maulana Afif; Ricky Aston Susetyo; Muhammad Ahmad Baballe
Computer Science and Information Technologies Vol 4, No 2: July 2023
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/csit.v4i2.p127-134

Abstract

One of the policies that have been made by the World Health Organization (WHO) and the Indonesian government during this COVID-19 pandemic, is to use an oximeter for self-isolation patients. The oximeter is used to monitor the patient if happy hypoxia which is a silent killer, happens to the patient. To maintain body endurance, exercise is needed by COVID-19 patients, but doing too much exercise can also cause decreased immunity. That’s why fatigue level and exercise intensity need to be monitored. When exercising, social distancing protocol should be also reminded because can lower COVID-19 spreading up to 13.6%. To solve this issue, the Caring Jacket is proposed which is a health monitoring jacket integrated with an IoT system. This jacket is equipped with some sensors and the global positioning system (GPS) for tracking. The data from the test showed the temperature reading accuracy is up to 99.38%, the oxygen rate up to 97.31%, the beats per minute (BPM) sensor up to 97.82%, and the precision of all sensors is 97.00% compared with a calibrated device.
Performance Evaluation of Sliding Mode Control (SMC) for DC Motor Speed Control Dimas Dwika Saputra; Alfian Ma'arif; Hari Maghfiroh; Muhammad Ahmad Baballe; Angelo Marcelo Tusset; Abdel-Nasser Sharkawy; Rania Majdoubi
Jurnal Ilmiah Teknik Elektro Komputer dan Informatika Vol 9, No 2 (2023): June
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26555/jiteki.v9i2.26291

Abstract

DC motor is an industrial motor that is practical for many applications and implementations. However, the speed of a DC motor often decreases because of the given load, thus causing it to be unstable and inconstant. In addition, parameter uncertainty is another issue of DC motors. The performance of the system will be impacted by the uncertainty. Therefore, in this study, SMC is used as speed control of the DC motor since it can handle non-linear plants. The performance also compares with PID to know the effectiveness of the SMC method in DC motor speed control. This study proposes a hardware design and implementation of DC motor angular speed control on Arduino UNO as an embedded control system. The performance comparison analysis results proved that both controllers could perform well. However, both controllers need further fine-tuning. There are still overshoot and steady-state errors for PID and SMC, respectively. In future work, the optimization method can be used to find the optimal gain or by combining it with an adaptive algorithm.
Prototipe Automatic Feeder dengan Monitoring IoT untuk Perikanan Bioflok Lele Hari Maghfiroh; Chico Hermanu; Feri Adriyanto
Electrician : Jurnal Rekayasa dan Teknologi Elektro Vol. 15 No. 1 (2021)
Publisher : Department of Electrical Engineering, Faculty of Engineering, Universitas Lampung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.23960/elc.v15n1.2160

Abstract

Revolusi Industri 4.0 telah banyak membawa banyak perubahan baik itu positif maupun negartif. Segi positifnya yaitu telah banyak dipakainya otomasi dan robot di dunia industri sehingga produksi bisa meningkat pesat. Sedangkan sudut negatif, semakin banyaknya pekerjaan manusia yang tergantikan oleh mesin sehingga memperkecil peluang kerja. Adanya revolusi industri 4.0 juga membawa kesenjangan antara kelompok melek teknologi dan kelompok gagap teknologi (gaptek). Warga kampung atau desa merupakan kelompok besar dari golongan gaptek. Untuk itu, suatu peluang usaha baru yang dapat dikerjakan msyarakat desa dengan tingkat pendidikan menengah sangat diperlukan. Maka dipilihlah program perikanan bioflok lele. Sentuhan teknologi otomasi dan Internet of Things (IoT) diberikan untuk meningkatkan produktivitas dan membuat masyarakat melek akan perkembangan teknologi era revolusi industry 4.0.
Co-Authors Abdel-Nasser Sharkawy Alfian Ma’arif Angelo Marcelo Tusset Augustinus Sujono Azis Ubaidilah Chico Hermanu Daru Kusumastuti Dimas Dwika Saputra Dodi Saputra Feri Adriyanto Feri Adriyanto Inayati Inayati Joko Slamet Saputro Maulana Afif Muhammad Ahmad Baballe Muhammad Dhafier Mu'afa Muhammad Fiqih Al Faishal Muhammad Hammam Al-Choiri Muhammad Nizam Muhammad Raflie Pangestu Phichitphon Chotikunnan R Lulus Lambang GH Rania Majdoubi Rebbeka Siswandina Sari Refansyah Basu Dewa Ricky Aston Susetyo Safinta Nurindra Rahmadhia