Garuda - Garba Rujukan Digital

CENTRAL KALIMANTANâS FAST GROWING SPECIES: SUITABILITY FOR PULP AND PAPER Adi, Danang Sudarwoko; Wahyuni, Ika; Risanto, Lucky; Rulliaty, Sri; Hermiati, Euis; Dwianto, Wahyu; Watanabe, Takashi
Indonesian Journal of Forestry Research Vol 2, No 1 (2015): Indonesian Journal of Forestry Research
Publisher : Secretariat of Forestry Research and Development Agency

Fast growing wood species could be promising to fulfill the gap between wood demand and supply. Due to their low quality, the utilization of fast growing wood species has been limited to pulp and paper. Our previous study on the fiber characteristic and density of the 30 unutilized fast growing wood species from PT Sari Bumi Kusuma, Central Kalimantan, showed that there were five species which could be promising as pulp and paper material. These wood species have fiber lengths of more than 2200 Âµm. This research was conducted to get information another property of the five woods to more discover their potential utilization, especially for pulp and paper material. The wood species investigated were Endospermum diadenum, Dillenia sp., Adinandra dumosa, Adinandra sp., and Nauclea junghuhnii. The results showed that these five species have a long of fiber length, which are classified in Class I, low to medium density, fiber derived value which the total score felt in the class I. The chemical compositions showed that extractive, holocelullose, Î±-cellulose, and lignin contents were 1.74-4.12%, 62.73-73.83%, 37.24-46.97%, 29.68-38.92%, respectively. Based on fiber characteristic, density, and chemical properties, these five species could be used as an alternative raw material for pulp and paper industries.Â

EXPLORATION OF POTENTIAL TREE SPECIES IN SUMBA ISLAND Lestari, Eka; Amin, Yusup; Pramasari, Dwi Ajias; Dwianto, Wahyu
Teknologi Indonesia Vol 41, No 1 (2018)
Publisher : LIPI Press

ABSTRACTSumba Island is a part of Wallace region which located in between Asia and Australia continents. Therefore it has a lot of endemic flora and fauna species. Laiwangi Wanggameti National Park (LWNP) is one of area in Sumba Islands which represented of this condition. The aim of this study is to determine the potential of tree species in Sumba Island based on strength class and commercial class. The wood samples were taken from 9 plots by wood increment borer at 1.3 meters height (breast height). The physical properties (specific gravity) were measured to determine the wood strength classes. The results found 35 species of potential tree species which can be classified into strength class II (13 species), III (19 species), IV (2 species), and V (1 species). Based on commercial classes, 63% of the tree species were classified into lesser known timbers. Furthermore, we think the potential tree from LWNP can be used for research purpose in forestry, especially in domestication study. Keywords: wood strength class, commercial class, bor riap, Laiwangi Wanggameti National Park, domestication ABSTRAKPulau Sumba merupakan bagian dari kawasan Wallacea yang berada di antara Benua Asia dan Australia. Oleh karena itu, pulau ini memiliki banyak flora dan fauna endemik. Taman Nasional Laiwangi Wanggameti (TNLW) adalah suatu wilayah di Pulau Sumba yang merepresentasikan kondisi secara umum di kawasan tersebut. Tujuan dari penelitian ini adalah untuk menentukan jenis kayu potensial di Pulau Sumba berdasarkan kelas kuat dan kelas komersial. Sampel kayu diambil dari 9 plot dengan menggunakan bor riap pada ketinggian 1,3 meter (setinggi dada). Sifat fisik (berat jenis) diukur untuk menentukan kelas kuat kayu. Hasil menunjukkan bahwa ditemukan 35 jenis kayu yang potensial yang dapat diklasifikasikan ke dalam kelas kuat II (13 jenis), III (19 jenis), IV (2 jenis), dan V (1 jenis). Berdasarkan kelas komersial, 63% jenis kayu yang didapatkan merupakan jenis kayu yang kurang dikenal. Oleh karena itu, jenis-jenis kayu yang potensial dari TNLW ini dapat digunakan untuk kepentingan penelitian di bidang kehutanan, lebih khususnya pada penelitian tentang proses domestikasi jenis-jenis tersebut. Kata Kunci: kelas kuat kayu, kelas komersial, increment borer, Taman Nasional Laiwangi Wanggameti, domestikasi

Botanical Garden including information on their physical and mechanical properties, natural durability, distribution, prospect and other supporting data; (2) to analyze the lesser-known wood species that could be used for construction materials and then recommend them to be developed through Industrials Plantation Forest. The steps of the study were first collection of data on timber species from herbarium catalogue; second collection of data on the properties of wood from various sour Ika WAHYUNI; Wahyu DWIANTO; Yusup AMIN; Teguh DARMAWAN
Jurnal Ilmu dan Teknologi Hasil Hutan Vol. 1 No. 2 (2008): Jurnal Ilmu Teknologi Hasil Hutan
Publisher : Departemen Hasil Hutan, IPB

Show Abstract | Download Original | Original Source | Check in Google Scholar

Botanical Garden including information on their physical and mechanical properties, natural durability, distribution, prospect and other supporting data; (2) to analyze the lesser-known wood species that could be used for construction materials and then recommend them to be developed through Industrials Plantation Forest. The steps of the study were first collection of data on timber species from herbarium catalogue; second collection of data on the properties of wood from various sources; third, observation of stem morphology in the field. The result of the catalogue study showed that there were 291 timber tree species grown in Cibodas Botanical Garden which were comprised of 14 major commercial timbers, 74 minor commercial timbers, and 142 lesser known timbers. These timber species were also distributed in other parts of Indonesia. Observation in the field then generated 49 lesser-known wood species that could be used for construction materials based on their stem form and branch height. From the reference and catalogue study, it was found that there were 14 wood species belongs to strength class I to III with natural durability ranges from very durable to moderate. These woods were then evaluated based on their morphological features and prospects. Finally, it was found that only ten wood species that were suitable to be used for construction materials, i.e. Acmena acuminatissima (Blume.) Merr. & Perry (Kelat); Adenanthera microsperma Teijsm. & Binn. (Saga); Baccaurea parviflora (Muell. Arg.) (Setambun); Casuarina junghuhniana Miq. (Cemara Gunung); Garcinia parvifolia and G. beccari (Manggis Hutan); Gymnostoma sumatranum (Joogb. ex de Vriese) L.A.S. Johnson (Cemara Sumatra); Mimusops elengi L. (Tanjung); Neonauclea lanceolata and N. obtusa (Ki Anggrit). However, the result of this study needs to be supported by further study on their wood properties since the present data were mostly qualitatives. Further research concerning their silviculture, growth rate, and susceptibility to the diseases were also needed to be done. Keywords : Lesser-known timbers, Cibodas Botanical Garden.

Tinjauan Hasil-hasil Penelitian Faktor-faktor Alam yang Mempengaruhi Sifat Fisik dan Mekanik Kayu Indonesia Review of Researches on Natural Factors Affecting the Physical and Mechanical Properties of Indonesian Wood Wahyu Dwianto; Sri Nugroho Marsoem
Jurnal Ilmu dan Teknologi Kayu Tropis Vol 6, No 2 (2008): Jurnal Ilmu dan Teknologi Kayu Tropis
Publisher : Masyarakat Peneliti Kayu Indonesia

This review deals with several topics concerning natural factors affecting physical and mechanical properties of wood, i.e. (1) wood species; (2) age and location of growing; (3) position of wood sample in the stem; (4) diameter; (5) humidity, moisture content, and temperature; (5) weathering and fungi; (6) forest fired; that have been done by researchers who are members of Indonesian Wood Research Society. The purposes of this review are (1) to evaluate the research results that have been done, (2) to promote the applicable and feasible utilization of research results to the users, (3) to provide information concerning previous researches that might be useful for further researches.More than 60 wood species have been reported in this review. Besides the major and minor commercial wood species; lesser known species, i.e. Balsa (Ochroma spp.), Randu (Ceiba pentandra Gaertn.), Merkubung (Macaranga sp.), Cengkeh (Eugenia aromatica L.), Afrika (Maesopsis eminii), Kisereh (Cinnamomum porrectum (Roxb) Kosterm), Kibawang (Melia excelsa Jack.), Pulai Konggo (Alstonia kongoensis Engl.), Sengon Buto (Enterolobium cyclocarpum Griserb.), Salamander (Grevillea robusta A.Cunn.), Kilemo (Litsea cubeba Pers.), Tahongai (Kleinhovia hospita Linn.), Sukun (Arthocarpus altilis), Arang (Diospyros borneensis), Berumbung (Adina minutifolia), Tisuk/Waru (Hibiscus macrophyllus), Urograndis (Eucalyptus urograndis), Kelapa (Cocos nucifera L.), Kelapa Sawit (Eleais guineensiis Jacq.), Laban (Vitex Pubescens Vahl.), Rambai (Baccaurea motleyana Muell.), Ki Sampang (Evodia latifolia DC.), Nangka (Artocarpus integra Merr.), Kalapi (Kalappia celebica), Gofasa (Vitex coffasus), Ketileng (Vitex glabrata), Cemara (Gymnostoma sp.), and Lamtoro (Leucaena glauca (Willd) Benth). have also been observed. The researches were generally done in relation to the utilization prospect of lesser known species, crops estate species, fast growing species, timber estate species, rural forest species, commercial species, for contruction/structural materials, handy-craft, musical instruments, or out-door exposures.Wood properties were interaction between specific gravity or density, moisture content, shrinkage and mechanical properties of wood. However, the values of those physical and mechanical properties in the papers could not directly compared to each other, because there were various testing standard and strength classification used. And unfortunately, researches on acoustic, thermal, electrical, creep, relaxation, and fatigue behaviour of Indonesian wood species were very rare or almost none.

Fiksasi Bambu Gombong dan Tali Fixation of Gombong and Tali Bamboos Wahyu Dwianto; Toshiro Morooka; Misato Norimoto
Jurnal Ilmu dan Teknologi Kayu Tropis Vol 2, No 1 (2004): Jurnal Ilmu dan Teknologi Kayu Tropis
Publisher : Masyarakat Peneliti Kayu Indonesia

This research describes stress relaxation measurement to understand the fixation mechanism of compressive deformation of water saturated Gombong bamboo (Gigantochloa pseduarundinaceae) and Tali bamboo (Gigantochloa apus). Stress relaxations are measured by compressing the specimens in radial direction to 0.2 strains between 110ºC and 190ºC for various periods of time in electro oil hydraulic testing system equipped with an autoclave, which was heated by high temperatures saturated steam. The stress approximately disappears in 60min at 170ºC, in 30min at 180ºC, and in 20 min at 190ºC for Gombong bamboo. On the other hand, the fastest release of stress is found for Tali bamboo. The plots of relationship between residual stress and strain recovery of Gombong and Tali bamboos lay on a single curve, respectively. The relationship is similar to that of Sugi wood by heating. However, the weight loss of the two bamboos is extremely higher than that of wood. The fixation is achieved at a weight loss of 20% for Gombong and Tali bamboos. From these results, the fixation mechanism is considerably dominated by the decomposition of hemicelluloses and lignin.

Modifikasi Alat Pelengkung Kayu Skala Pilot dengan Menggunakan Pemanas Modification of Pilot-scale Wood Bending by Heating Elements Teguh Darmawan; Jayadi Jayadi; Sudijono Sudijono; Ika Wahyuni; Yusuf Amin; Wahyu Dwianto
Jurnal Ilmu dan Teknologi Kayu Tropis Vol 4, No 1 (2006): Jurnal Ilmu dan Teknologi Kayu Tropis
Publisher : Masyarakat Peneliti Kayu Indonesia

This paper deals with manufacturing and modification of pilot-scale wood bending machine by heating elements. The machine has specifications as follows: 1000 mm width; 1305 mm height; 430 mm and 470 mm radius of upper part and bottom part of bent plates, respectively; and a manual stick pressure with 870 mm length. The upper part and bottom part of bent plates are equipped with heating elements, which the maximum of temperature is arranged to 200°C by the electric force of 220V/2000 watt. Left and right sides of bent plates are covered by 1150 mm x 950 mm insulation board to maintain the heat. From the temperature measurement, the heating plates were reached 50°C in 2.5 minutes, 100°C in 9.5 minutes, and 180°C in 28 minutes. The modified machine has successfuly bent Acacia solid wood with dimensions of 1100 mm(L) x 50 mm(T) and 10 mm, 20 mm, and 30 mm in thickness (R).

Sifat Ketahanan Api Lima Jenis Kayu dengan Pelapisan Carbon Phenolic Spheres (CPS) yang Diuji dengan Cone Calorimeter Fire Resistance Properties of Five Wood Species Laminated with Carbon Phenolic Spheres (CPS) Tested by Cone Calorimeter Subyakto Subyakto; Wahyu Dwianto
Jurnal Ilmu dan Teknologi Kayu Tropis Vol 2, No 1 (2004): Jurnal Ilmu dan Teknologi Kayu Tropis
Publisher : Masyarakat Peneliti Kayu Indonesia

In all aspects of wood utilization their fire resistance properties are very important; therefore efforts to enhance those properties are needed. In the previous study, graphite phenolic spheres (GPS) laminated on woods and plywood enhanced their fire properties. Carbon phenolic spheres (CPS) is a new material made from a mixture of wood char and phenolic resin, this material is cheaper than GPS. In the present experiment, CPS sheet was laminated on five wood species and their fire resistance properties were evaluated using cone calorimeter.　The five wood species are randu (Bombax ceiba L.), angsana (Pterocarpus indicus Jacq.), mindi (Melia azedarach L.), puspa (Schima wallichii DC Korth), and mahoni (Swietenia mahagony L. Jacq). The specimen was 100 mm x 100 mm with thickness of 30 mm tested with cone calorimeter in accordance with ISO 5660 standard. Using cone calorimeter a homogenous heat was exposed to the surface of wood specimen, and ignited with igniter. About 1 mm thick of CPS sheet was laminated on the wood surface (100 mm x 100 mm). Specimen was tested at horizontal position and at heat flux of 40 kW/m2. On the unexposed wood surface, thermocouple was attached to measure increases of temperature. Results showed that five species of wood laminated with CPS have higher fire properties compared with control wood, however compared with woods laminated with GPS those results were lower.

Pengaruh Suhu dan Tekanan Uap Air terhadap Fiksasi Kayu Kompresi dengan menggunakan Close System Compression Temperature and Steam Pressure Dependency on the Fixation of Compressed Wood by Close System Compression Yusuf Amin; Wahyu Dwianto
Jurnal Ilmu dan Teknologi Kayu Tropis Vol 4, No 2 (2006): Jurnal Ilmu dan Teknologi Kayu Tropis
Publisher : Masyarakat Peneliti Kayu Indonesia

It is known that compression wood by heat treatment needs approximately 20 hours at 180ºC to attempt the permanent fixation of compressive deformation. On the other hand, even the permanent fixation of compressive deformation by steam treatment is reached in 10 minutes at the same temperature, this method needs expensive apparatus and inapplicable for large wood dimensions. These both problems can be solved by Close System Compression (CSC) method. CSC is a method to press the wood inside an airtight seal chamber, which is placed between the two hot press plates. Wood moisture contents, which evaporate due to heat from hot press, are trapped inside the CSC and produce steam. The wood species used in this research was Randu (Bombax ceiba. L) with dimensions of 2 cm (L) x 2 cm (T) x 3 cm (R). The wood specimens were compressed into 2 cm in radial direction inside the CSC at 140ºC, 160ºC, and 180ºC for 10 min, 20 min and 30 min. They were compressed in air-dried, water saturated and steam saturated conditions, because it was predicted that moisture content of wood and steam pressure, which was produced inside the CSC has significantly effects on the fixation of wood, beside the temperature.The result shows that moisture content of the wood has an effect on the decreasing of recovery of set. However, it was needed 180ºC temperature and 10 kg/cm2 steam pressure to attempt the permanent fixation. Therefore, it was necessary to add water to produce the steam pressure besides that was produced from the evaporation of wood moisture content.

The Effect of Steaming and Heat-Compression on the Properties of Jabon Wood for Furniture Materials Efrida Basri; Abdurachman Abdurachman; Wahyu Dwianto
Jurnal Ilmu dan Teknologi Kayu Tropis Vol 12, No 2 (2014): Jurnal Ilmu dan Teknologi Kayu Tropis
Publisher : Masyarakat Peneliti Kayu Indonesia

The inferior properties of juvenile jabon wood (Anthocephalus cadamba Miq.) limit its utility. Densification through heat-compression presently conducted is possibly useful to improve its properties. Preceding heat-compression, jabon wood samples were either steamed or non-steamed. Heat-compression temperatures were varied at 170 C, 180 C and 190 C. Compression was carried out until 20% reduction in wood thickness. Physical and mechanical properties and machining properties of the compressed wood samples were determined in accordance with standard procedures of ASTM D143-94 and ASTM D1666-64, respectively. In the present works, both of the ASTM standard referred were slightly modified. X-ray diffractometer (XRD) was used to determine crystallinity degree of wood. The result showed that either steamed or not, densification was successfully increased the properties of juvenile jabon wood and satisfied the requirement of wood for furniture raw materials.Keywords: furniture, heat pressure, steaming, wood properties, young age-jabon

Fiber and Chemical Characteristics of Branchwoods of Three Meranti Species Danang S Adi; Lucky Risanto; Ika Wahyuni; Sukma S Kusumah; Wahyu Dwianto; Taka Hayashi
Jurnal Ilmu dan Teknologi Kayu Tropis Vol 9, No 2 (2011): Jurnal Ilmu dan Teknologi Kayu Tropis
Publisher : Masyarakat Peneliti Kayu Indonesia

The fiber and chemical characteristics of branchwoods of three meranti species namely meranti sangkan, meranti bakau, and meranti bunga kulit hitam from Bukit Batu Peat Swamp Forest, Riau were observed. The aim of this research was to discover the potential utilization of these three meranti species based on their characteristic. The result showed that holocellulose contents of meranti sangkan, meranti bakau, and meranti bunga kulit hitam were 72.97%, 75.28%, and 69.88%, whereas the α-cellulose contents were 43.55%, 51.14%, and 43.25%, respectively. meranti sangkan had the highest lignin content (35.99%) followed by meranti bakau (34.21%) and meranti bunga kulit hitam (32.18%). meranti Bunga kulit Hitam had the highest extractive content (2.24%) followed by meranti sangkan (1.66%) and meranti bakau (1.08). Furthermore, the fiber length of meranti bunga kulit hitam, meranti sangkan, and meranti and meranti Hitam were 1475.45 μm, 1475.45 μm, 1442.62 μm, and 1205.23 μm, respectively. The values of fiber derivative of the three meranti species were slightly differ from class I, except for felting power that was classified in class III. The result also showed that the branchwoods of the three meranti species are suitable for pulp and paper raw material.Key words: fiber and chemical properties, meranti bakau, meranti sangkan, meranti bunga kulit hitam, peat swamp forest

Title

Found 15 Documents
Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title Search

Found 15 Documents Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title

Found 15 Documents
Search