Garuda - Garba Rujukan Digital

p-Index From 2019 - 2024

1.456

P-Index

This Author published in this journals

All Journal SCHOOL EDUCATION JOURNAL PGSD FIP UNIMED Jurnal Teknik Mesin dan Mekatronika (Journal of Mechanical Engineering and Mechatronics) Petro : Jurnal Ilmiah Teknik Perminyakan JURNAL ABDI MASYARAKAT INDONESIA (JAMIN)

Samsol Samsol

Universitas Trisakti

Author-ID : 2568677

Earth & Planetary Sciences Economics, Econometrics & Finance Energy Engineering Environmental Science Languange, Linguistic, Communication & Media Materials Science & Nanotechnology Mechanical Engineering Transportation Other

Published : 7 Documents Claim Missing Document

Claim Missing Document

Articles

STUDI LABORATORIUM PEMILIHAN ADDITIF PENSTABIL SHALE DI DALAM SISTEM LUMPUR KCL-POLIMER PADA TEMPERATUR TINGGI Zakky Zakky; Bayu Satyawira; Samsol Samsol
Journal of Mechanical Engineering and Mechatronics Vol 3, No 1 (2018): JOURNAL OF MECHANICAL ENGINEERING AND MECHATRONICS
Publisher : President University

Mud is one of the things that is very supportive in drilling operations, the design of the mud can affect the effectiveness of drilling work, the costs to be incurred, up to when the well is in production. Of course what is expected from a mud usage is low expenditure and drilling with optimal results. Drilling mud plays a very important role in a drilling operation. Drilling that can run quickly, safely and economically is greatly influenced by the conditions and sludge system used. The condition referred to here is how the properties or rheology of the mud. Whereas the mud system referred to here is a certain type of mud that must be used with regard to the state of the formation and borehole. Muddy KCl-POLYMER is a non-dispersed mud, where the hydration and dispersion process of the shale formation drilled must be maintained or maintained as much as possible. There are several ways to achieve this, the most common of which is to limit the amount of water that reacts with the shale, by covering the cutting produced by the shale with the polymer as soon as possible to prevent further reactions with water. In this study, we will analyze the use and physical properties of drilling mud using KCl-Polymer sludge which is carried out in the Trisakti University Laboratory of Petroleum Drilling and Production.

METODE NORMATIVE SURVEY DALAM ANALISA DAMPAK PENERAPAN KEGIATAN MBKM Suryo Prakoso; Shabrina Sri Riswati; Muhammad Burhannudinnur; Sigit Rahmawan; Pantjanita Novi Hartami; Samsol Samsol; Mixsindo Korra Herdyanti; Cahaya Rosyidan; Onnie Ridaliani Prapansya; Havidh Pramadika; Ririn Yulianti
SCHOOL EDUCATION JOURNAL PGSD FIP UNIMED Vol 12, No 1 (2022): SCHOOL EDUCATION JOURNAL PGSD FIP UNIMED
Publisher : Universitas Negeri Medan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24114/sejpgsd.v12i1.32895

The Independent Campus Learning Program (MBKM) is a government program in an effort to provide opportunities for students from both public and private universities to study outside their study program. The opportunity is also wide open for students. This research is an analytical study of the implementation of MBKM competition activities in the Petroleum Engineering Study Program, FTKE Trisakti University. This study is supported by data obtained from the descriptive survey method (Normative Survey Method) of the entire academic community which includes the heads of the Faculties and Study Programs, lecturers, education staff and students as respondents. This study is intended to evaluate the impact of MBKM-based learning on lecturers and students, the availability and implementation of MBKM-based curriculum in Petroleum Engineering Study Program, Trisakti University and the level of satisfaction of lecturers, students and stakeholders on the availability of facilities and infrastructure to support the implementation of MBKM. The survey results show that MBKM activities have had a positive impact. Some of the challenges faced, among others, were the difficulty in getting partners to provide internship programs, technical constraints due to the pandemic, and program socialization that had not yet touched the entire academic community. More intensive efforts from Faculties and Study Programs to build cooperation with partners and update socialization methods are expected to improve the implementation of MBKM.

KAJIAN RENTANG BATAS KEWAJARAN UTILISASI PRODUKSI KILANG MINYAK INDONESIA Andry Prima; Bayu Satiyawira; Cahaya Rosyidan; Samsol Samsol
PETRO:Jurnal Ilmiah Teknik Perminyakan Vol. 7 No. 3 (2018): Desember
Publisher : Jurusan Teknik Perminyakan Fakultas Teknologi Kebumian dan Energi Universitas Trisakti

Pada kurun waktu awal hingga akhir 2016, terhentinya produksi kilang yang memprodusikan bahan bakar minyak secara tak terduga atau dikenal sebagai “unplanned shutdown” berpotensi menyebabkan penurunan produksi bahan bakar minyak (BBM) secara kseluruhan. Paper ini berupaya menyajikan “Lesson Learnt” yang dapat diambil oleh kilang-kilang di Indonesia dengan bercermin kepada “benchmark” guna memberikan gambaran dimana posisi utilisasi dari kilang-kilang Indonesia tersebut.

OPTIMASI PRODUKSI SUMUR EC-6 DENGAN MEMBANDINGKAN PENGANGKATAN BUATAN GAS LIFT DAN ELECTRIC SUBMERSIBLE PUMP Jonathan Jonathan; Sisworini Sisworini; Samsol Samsol; Hari Oetomo
PETRO:Jurnal Ilmiah Teknik Perminyakan Vol. 8 No. 1 (2019): MARET
Publisher : Jurusan Teknik Perminyakan Fakultas Teknologi Kebumian dan Energi Universitas Trisakti

In the world of oil is very common in the production system. This production system produces oil from wells after drilling and well compressions. Over time, the production of a well may decrease due to several parameters of pressure drop and the presence of clay which makes the pipe diameter narrower. There are several methods used to increase the decrease in production including adding artificial lifts such as sucker rod pump, electric submersible pump and gas lift, reservoir stimulation and pipe cleaning if the pipe diameter is reduced due to clay. The well has been installed an artificial lift is a gas lift and this well need an optimization to increase its production. The EC-6 well optimization is planned by comparing the lift-up scenario of the gas lift by adjusting the rate of gas injection and deepening the orifice injection and also an installation of electrical submersible pump. Best percentage of optimization production from EC-6 Well, last scenario is chosen which is new installation artificial lift ESP from gas lift (existing) and gaining 18.52% form existing production

PENGARUH SCALE TERHADAP PRODUKTIVITAS PADA SUMUR BN-52, BN-104, DAN BN-110 DI LAPANGAN “X” Abhikama Pradipta; Lestari Lestari; Samsol Samsol
PETRO:Jurnal Ilmiah Teknik Perminyakan Vol. 8 No. 1 (2019): MARET
Publisher : Jurusan Teknik Perminyakan Fakultas Teknologi Kebumian dan Energi Universitas Trisakti

BN-52, BN-104, and BN-110 wells are located on the X field, PT. PERTAMINA FIELD RAMBA ASSET 1, South Sumatra. The three wells are oil-producing wells in field X. Using the Vogel equation, the IPR curve and maximum flow rate of each well are obtained, which are 152.14 BOPD, 57.2 BOPD, and 53.76 BOPD respectively. By using the exponential Decline Curve Analysis calculation method, it can be seen the rate of decline in production, as well as the time of well production to economic limit. The results of the Decline Curve Analysis show that the BN-52 well will still be in production until March 2022, and the BN-110 well can produce until March 2020. In the analysis with the Stiff & Davis Method, carbonate deposits are proven, with each Stability Index value +1.19, +1.60, and +1.35, whereas with the Skillman, Mcdonald & Stiff method there was no scale sulfate, with S values of each well at 57,272 meq / l, 54,416 meq / l, and 55,147 meq / l. The scale causes oil production to decrease, consequently the IPR curve shifts to the left. The decreasing production of the three wells is due to a scale that inhibits the flow rate. Maximum flow rate was obtained by using the Standing correlation in each well of 100.06 BOPD, 54.53 BOPD, and 28.72 BOPD. The decline in oil production caused by scales must be handled appropriately.

PEMILIHAN POLA INJEKSI AIR DENGAN MENGGUNAKAN SIMULASI RESERVOIR UNTUK OPTIMASI PRODUKSI LAPANGAN ‘R’ Rantan Rantan; Maman Djumantara; Samsol Samsol
PETRO: Jurnal Ilmiah Teknik Perminyakan Vol. 9 No. 2 (2020): JUNI
Publisher : Jurusan Teknik Perminyakan Fakultas Teknologi Kebumian dan Energi Universitas Trisakti

Lapangan ‘RR’ merupakan model lapangan yang mendekati ideal dengan kriteria model yaitu layer cake model dan homogen. Lapangan ‘RR’ ini tidak memiliki sejarah produksi dan dianggap akan dilakukan suatu pengembangan dengan menambahkan sumur injeksi maupun produksi dalam waktu bersamaan serta memiliki nilai OOIP daerah yang diteliti sebesar 27.60 MMSTB. Adapun satu basecase dan empat skenario yang dibuat, dengan pola injeksi yang memiliki ukuran pola yaitu 40 acre dan terdapat 13 konfigurasi pola. Kemudian, skenario yang akan dianalisis kinerjanya diantaranya Five Spot atau Seven Spot dalam keadaan Normal ataupun Inverted. Uji sensitivitas dilakukan dengan rate injeksi antara 4000 bwpd hingga 100000 bwpd. Prediksi performa produksi injeksi air yang diamati kumulatif produksinya dimulai dari tahun 2019 hingga 2040. Dimulai dari skenario I yaitu pola injeksi five spot normal dengan rate injeksi 35000 bwpd menghasilkan Np sebesar 16.72 MMSTB (RF 60.56%), skenario II pola five spot inverted dengan rate injeksi 100000 bwpd menghasilkan Np sebesar 16.64 MMSTB (RF 60.27 %) skenario III pola seven spot normal dengan rate injeksi 35000 bwpd menghasilkan Np sebesar 16.06 MMSTB (RF 58.18 %), dan skenario IV pola seven spot inverted dengan rate injeksi 100000 bwpd menghasilkan Np sebesar 16.34 MMSTB (RF 59.21 %). Berdasarkan kumulatif produksinya, skenario yang paling optimum adalah skenario I yaitu pola five spot normal dengan rate injeksi 35000 bwpd

PENYULUHAN DAN PELATIHAN PEMANFAATAN LIMBAH PLASTIK SEBAGAI BAHAN BAKAR DI PANDEGLANG, BANTEN Samsol Samsol; Sigit Rahmawan; Apriandi Rizkina; Ridha Husla; Havidh Pramadika
Jurnal Abdi Masyarakat Indonesia (JAMIN) Vol 1 No 1 (2019): JURNAL ABDI MASYARAKAT INDONESIA (JAMIN)
Publisher : Universitas Trisakti

Volume limbah plastik yang semakin banyak, serta semakin mahal dan langkanya bahan bakar rumah tangga menjadi tantangan peneliti dalam mencari energi baru dan terbarukan sekaligus memanfaatkan barang – barang yang dianggap limbah menjadi barang yang bisa memiliki pengganti energi alternatif, sehingga dapat membantu masyarakat dalam mengoptimalkan ekonomi keluarga. Kegiatan PKM ini bertujuan untuk memberikan penyuluhan dan pelatihan kepada masyarakat agar dapat memanfaatkan limbah plastik yang tidak dimanfaatkan untuk menjadi bahan bakar alternatif yang dapat dimanfaatkan masyarakat sebagai bahan bakar di rumah tangga. Sehingga dapat membantu masyarakat dalam pengeluaran pembeliaan gas maupun minyak tanah sebagai bahan bakar dalam memasak maupun bahan bakar kendaraan.

Co-Authors Abhikama Pradipta Andry Prima Apriandi Rizkina Bayu Satiyawira Bayu Satyawira Cahaya Rosyidan Hari Oetomo Havidh Pramadika Jonathan Jonathan Lestari Lestari Maman Djumantara Mixsindo Korra Herdyanti Muhammad Burhannudinnur Onnie Ridaliani Prapansya Pantjanita Novi Hartami Rantan Rantan Ridha Husla Ririn Yulianti Shabrina Sri Riswati Sigit Rahmawan Sisworini Sisworini suryo prakoso Zakky Zakky

Title

Found 7 Documents
Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title Search

Found 7 Documents Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title

Found 7 Documents
Search