Claim Missing Document
Check
Articles

Found 9 Documents
Search

Perbaikan Desain Proteksi Petir Saluran Transmisi 150 kV Payakumbuh – Koto Panjang Yusreni Warmi; Fauzan Ismail
Jurnal Teknik Elektro Vol 7, No 1 (2018): Jurnal Teknik Elektro
Publisher : Situs resmi ITP Press

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (827.422 KB)

Abstract

Aktifitas petir di Indonesia sangat tinggi, dan trip-out petir pada saluran transmisi sering terjadi. Pada artikel ini, kinerja petir pada saluran transmisi 150 kV Payakumbuh – Koto Panjang diteliti secara detail dan menunjukan bahwa tingkat trip-out petir tergantung pada aktifitas petir di area sekitarnya, tahanan kaki menara, panjang span dan panjang dari gap arching horn. Tingkat trip-out petir yang diamati sesuai dengan hasil simulasi dengan menggunakan program IEEE Flash. Ketika tahanan kaki menara pada semua menara di seting kurang dari 10 dan panjang dari gap arcing horn di seting menjadi 1.2 m sampai 1.3 m, tingkat trip-out petir diharapkan berkurang 50% dari tingkat trip-out petir yang terjadi.
Perbaikan Performa DC-Link Inverter Satu Fasa Menggunakan Interleaved dc-dc Boost Converter pada Aplikasi Photovoltaics Fauzan Ismail; Yusreni Warmi; Andi M. Nur Putra
Jurnal Teknik Elektro Vol 7, No 1 (2018): Jurnal Teknik Elektro
Publisher : Situs resmi ITP Press

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (739.684 KB)

Abstract

Penelitian ini menyajikan penggunaan Interleaved dc-dc boost converter pada aplikasi photovoltaics. Topologi interleaved dc-dc boost konverter dapat mengurangi riak arus masukan, riak tegangan keluaran, dan memperkecil arus yang melalui komponen switching, sehingga konverter ini dapat diimplementasikan pada daya besar dan tegangan output yang besar. Perbandingan performa antara interleaved dc-dc boost converter dengan konverter boost konvensional, disimulasikan menggunakan software PSIM. Kedua konverter dc-dc dengan daya 1kW, tegangan input 60V dan tegangan output 300V akan diverifikasi.
Perencanaan Koordinasi Isolasi Peralatan Tegangan Tinggi Gardu Induk 150 kV Berdasarkan Arus Surja Petir Pada Sistem Interkoneksi Sumatera Bagian Selatan (Sumbagsel) dan Sumatera Bagian Tengah (Sumbateng) Yusreni Warmi; Dasman Dasman; Minarni Minarni
Jurnal Momentum ISSN 1693-752X Vol 14, No 1 (2013): Volume 14 No 1 Februari 2013
Publisher : ITP Press

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (436.808 KB)

Abstract

The simulation results show the influence arrester laying, the magnitude of overvoltage that occursin power transformer such as placement system arresters on transmission 150 kV transformer greatly affect the amount of voltage surges that occur in transformers and arresters, surge and affects the amount of current flowing in the wire melting of CO. System-1 is an effective placement system arresters. In terms of voltage surges generated: the system is not easy to produce high voltage surges that of the four systems, the system-1 is a system that produces the low-voltage surge in both the transformer and the arresters. Overvoltage that occurs in the equipment due to lightning surge currents greater value if the distance laying lightning arresters of the equipment is the greater, for the laying of the lightning arrester at a distance of 6 meters, the peak voltage value on each piece of equipment, CT is 543.837 kV, CB is 566.659 kV, DS is 579.357 kV Arrester is 527.884 and 527.884 kV transformer is Power. Meanwhile, at a distance of 10 meters, overvoltage arising on each piece of equipment increases, the CT is 543.600 kV, CB is 567.269, DS is 579.381, 528.097 kV Arrester is and is 528.123 kV Power Transformer. The more steep lightning current waveforms into the substation, the greater the value of the voltage over to the protected equipment. For laying the same distance is 6 meters, acquired 527.884 kV to 87 kA lightning, 8/20, 559.222 kV to 87 kA lightning, 1/70, 558.803 kV to 87 kA lightning strike, 1.2 / 50.
PERENCANAAN PENEMPATAN ARRESTER TERHADAP EFEKTIVITAS PROTEKSI TRANSFORMATOR PADA GARDU INDUK 150 KV SISTEM INTERKONEKSI SUMATERA BAGIAN TENGAH - SUMATERA BAGIAN SELATAN Yusreni Warmi; Minarni Minarni; Dasman Dasman
Jurnal Momentum ISSN 1693-752X Vol 15, No 2 (2013): Volume 15 No 2 Agustus 2013
Publisher : ITP Press

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (792.773 KB)

Abstract

Penelitian ini merupakan pengembangan dari penelitian sebelumnya tentang perencanaan koordinasi isolasi peralatan tegangan tinggi Gardu Induk (GI) 150 kV, namun berdasarkan hasil penelitian tersebut, penentuan penempatan arrester terhadap transformator sangat menentukan tegangan lebih yang timbul pada peralatan yang ada pada GI. Maka berdasarkan pernyataan tersebut, perlu dilakukan penelitian selanjutnya mengenai perencanaan penempatan arrester terhadap efektivitas transformator pada GI 150 kV. Penelitian ini bertujuan untuk meningkatkan stabilitas sistem tenaga listrik untuk jangka panjang, khususnya untuk melihat efektivitas proteksi pada transformator, sehingga dapat memperkecil tegangan lebih yang muncul pada peralatan GI yakni transformator. Simulasi dilakukan dengan menggunakan Electromagnetic Transients Program (EMTP) sebagai perangkat lunak dengan cara memodelkan GI sesuai representasi peralatan-peralatan di gardu, dengan cara mempertimbangkan faktor-faktor yang mempengaruhi besarnya tegangan surja dan arus surja yang terjadi pada masing-masing sistem, seperti pengawatan arrester, panjang kawat yang dipergunakan dalam sistem penempatan arrester, kecuraman gelombang datang, dan kecepatan merambat gelombang surja. Sehingga pada akhirnya didapatkan satu sistem penempatan arrester yang efektif sebagai proteksi tranformator pada GI150 kV untuk sistem interkoneksi Sumbagteng dan Sumbagsel, guna mengevaluasi koordinasi isolasi pada GI tersebut. Hasil simulasi memperlihatkan adanya pengaruh peletakan arrester, bentuk gelombang surja petir terhadap besarnya tegangan lebih yang terjadi pada transformator daya. Selain itu hasil simulasi akan bisa dijadikan referensi untuk perencanaan peletakan arrester terhadap transformator pada perencanaan GI dengan tingkat tegangan yang lebih tinggi pada Sumbagteng sehingga diperoleh koordinasi yang optimal.
Analisis Variasi Ketebalan Coating Senyawa Glasir terhadap Daya Tahan Dielektrik Isolator Keramik Saluran Transmisi 150kV YUSRENI WARMI; KAZNI FEBRIAN
ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektronika Vol 9, No 2 (2021): ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektro
Publisher : Institut Teknologi Nasional, Bandung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26760/elkomika.v9i2.249

Abstract

ABSTRAKPenelitian ini bertujuan untuk mengetahui seberapa besar nilai coating isolator yang dapat ditembus listrik berdasarkan Basic Insulator Level (BIL). Metode yang digunakan dalam perhitungan tegangan tembus listrik ialah metode Anderson dalam hal ini Critical Fashover (CFO). Untuk mengetahui penurunan daya tahan dielektrik isolator dapat dilihat dari seberapa besar tegangan flashover yang dihasilkan. Hasil dari perhitungan disimulasikan dengan MATLAB logika fuzzy. Pada penelitian ini ketika isolator disetting pada coating 0,3 mm dengan waktu kejadian flash 2 μs maka tegangan flashover yang dihasilkan sebesar 1,3 MV. Hasil simulasi ini menunjukan bahwa pada coating 0,3 mm tegangan flashover yang dihasilkan melebihi dari BIL isolator yang sudah ditetapkan yakni sebesar 1,27 MV. Isolator dalam kondisi seperti ini dapat ditembus listrik atau daya tahan dielektriknya menurun. Secara bersamaan ketika kemampuan coating berkurang, maka dapat diklasifikasikan isolator dalam keadaan kotor.Kata kunci: isolator, coating, dielektrik, BIL, dan fashover ABSTRACTThis research aims to determine the value of the insulator that can be penetrated by electricity based on the Basic Insulator Level (BIL). The method used in the calculation of breakdown voltage is the Anderson method, in this case, Critical Flashover (CFO). To know a decrease in the dielectric resistance of the insulator can be seen from whatever the voltage resulting from a large flashover. The results of the calculations simulated with fuzzy logic Matlab. In this research, when the insulator set on a coating of 0.3 mm with a flash event time of 2 μs, then flashover voltage resulted in 1.3 MV. The simulation results show that at the coating 0.3 mm the result of flashover voltage exceeds the BIL insulator that has been set at 1.27 MV. Insulator in this condition can be penetrated by electricity or the dielectric resistance decreases. Simultaneously when the coating ability is reduced, then can be classified as a dirty insulator.Keyword: insulator, coating, dielectric, BIL, and flashover
STUDI PENGARUH BACK FLASHOVER PADA SALURAN TRANSMISI 150 kV PAYAKUMBUH - KOTO PANJANG Arfita Yuana Dewi; Yusreni Warmi; Peprizal Peprizal; Asnal Effendi
Ensiklopedia of Journal Vol 2, No 3 (2020): Vol 2 No 3 Edisi 2 April 2020
Publisher : Lembaga Penelitian dan Penerbitan Hasil Penelitian Ensiklopedia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (310.272 KB) | DOI: 10.33559/eoj.v2i3.536

Abstract

Back flashover is one of the consequences of a direct lightning strike. Back flashover is caused by the higher grounding resistance value of the tower leg. Doing so can create an overvoltage and can cause damage to electrical equipment. One way to minimize overvoltage due to back flashover is to adjust the grounding resistance at the foot of the tower. Tower 10 has a grounding resistance value of the tower foot of 4.78 ohms, the total back flashover is 29.085544 times / year. Tower 50 has a grounding resistance value of the tower foot of 14 ohms and the number of back flashover disturbances is 85.0213544 times / year. In tower 10 the value of the grounding resistance of the tower feet is smaller than the value of the grounding resistance of the menra feet 50, so the total number of back flashovers on tower 50 is higher than tower 10. The greater the value of the grounding resistance of the tower feet, the higher the number of back flashovers. The average grounding resistance of the tower leg 1 - 249 Payakumbuh Koto Panjang has a value of 4.2847 ohm tower foot grounding resistance, the number of back flashover disturbances is 24.593635 times / year. The standard grounding resistance of the tower leg is 10 ohms, because tower 50 has a grounding pressure value exceeding the standard, which is 14 ohms, so that it can cause the number of back flashover disturbances to exceed the standard 13 times / 100 km / year.
PERANCANGAN MODEL WIRELESS FAST CHARGING MENGGUNAKAN CONSTANT CURRENT PADA KENDARAAN LISTRIK Ridho Anfu salam; Andi Muhammad Nur Putra; Gilang Ramadhan; Salman Parizi; Anggun Anugrah; Yusreni Warmi
Prosiding Seminar Nasional Teknik Elektro, Sistem Informasi, dan Teknik Informatika (SNESTIK) 2022: SNESTIK II
Publisher : Institut Teknologi Adhi Tama Surabaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (452.096 KB) | DOI: 10.31284/p.snestik.2022.2754

Abstract

Beberapa tahun kedepan akan berkembang pesat dari sektor electrical vehicle karena dalam perkembangan ini sangat menguntungkan dari ramah lingkungan dan penghematan bahan bakar. Dalam pengisian mobil listrik saat ini mambutuhkan waktu yang cukup lama dalam pengisian. Jadi perlu dikaji hingga didapat pengoptimalan saat mengunakan electrical vehilce dalam pemakaian sehari-hari. Sistem pengisian yang sedang dikembangkan yaitu dengan wireless charging, sistem ini memungkinkan mempermudah dalam pengisian. Pada penelitian ini model yang akan dikembangkan menggunakan LC (Induktor Kapasitor) pada satu sisi. Pada penelitian ini menggunakan LC pada satu sisi yang merupakan pengembangan dari metode penggunaan LCC (Induktor Kapasitor Kapasitor), dari metode ini diharapkan dapat melakukan pengisian cepat. Proses pengisian baterai memiliki beberapa metode salah satu nya metode arus konstan. Metode arus konstan menerapkan arus konstan saat tegangan baterai meningkat hingga pengisian baterai penuh.
Proposal of analysis method to reduce back-flashover rate taking account of tower footing resistance Yusreni Warmi; Zulkarnaini Zulkarnaini; Abdul Rajab; Chitra Yuanisa; Rizki Oktrinanda Elyas; Andi M. Nur Putra; Zuriman Anthony
International Journal of Electrical and Computer Engineering (IJECE) Vol 13, No 1: February 2023
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/ijece.v13i1.pp94-106

Abstract

The number of lightning stroke on the tower of the 150 kV Koto Panjang-Payakumbuh transmission line located the rocky area has been observed. The high value of tower footing resistance indicates the occurrence of the back-flashover in the transmission line at intensity of 74%. The back-flashover occurrence is dominantly triggered by the tower footing resistance value. Also, the rate of back-flashover has an effect on the value of the tower footing resistance by considering the number of electrode installations. A design is proposed for the grounding system of the tower footings in order to reduce the rate of back-flashover. The results presenting in numerical simulation indicates that it works properly after adding 4 electrodes. That is to say, installing 4 electrodes in each tower has successfully decreased the tower footing resistance value, back-flashovers rate 80% and 90-95% of present value respectively. The insulator voltage can be reduced to less than half of the present voltages as much as 30-50%. In more detail, in tower 77, the value of the tower footing resistance drops to 2.84 Ω, the flashover rate drops to 0.57/100 km/year and the insulator voltage drops to 0.99 MV when a disturbance occurs.
Disturbance Modeling on Transmission Lines Using Wavelet Transform Method: A Review Sitti Amalia; Mardini Hasanah; Yusreni Warmi; Novizon Novizon; Abdul Rajab
Andalas Journal of Electrical and Electronic Engineering Technology Vol. 2 No. 2 (2022): November 2022
Publisher : Electrical Engineering Dept, Engineering Faculty, Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/ajeeet.v2i2.31

Abstract

This paper introduces a number of methods for identifying disturbances on transmission lines and provides algorithms for classifying various disturbance types. working with the discrete wavelets transform (DWT) and various embedded systems techniques using a simulator to carry out digital simulations of system trials using the controlled technique, the nature of disturbance in distinct sub-systems is determined. The analysis of transmission lines using the wavelet transform is the main topic of this study, along with techniques for transmission line protection. These factors include channel capacity, channel length, simulation software, mother wavelet type, parameters, sampling frequency, and type of disturbance analysis.