Article Per Year (5 Year)
p-Index From 2019 - 2024
0
P-Index
This Author published in this journals
All Journal Journal of the Civil Engineering Forum
Iman Satyarno
Department of Civil and Environmental Engineering, Universitas Gadjah Mada, Yogyakarta
Civil Engineering, Building, Construction & Architecture Environmental Science

Published : 2 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 2 Documents
Search

 1 
THE USE OF NATURAL TRASS FROM SAYUTAN MAGETAN AND LIME FROM NGAMPEL BLORA AS THE MATERIAL OF CEMENT SUBSTITUTION FOR MORTAR MIXTURE Muhammad Nurzain; Iman Satyarno; Muslikh Muslikh
Journal of the Civil Engineering Forum VOLUME: XXII/1 - January 2013
Publisher : Department of Civil and Environmental Engineering, Faculty of Engineering, UGM

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.22146/jcef.18915

Abstract

Construction works in the Regency of Magetan, as well as in the mountain area far from capital cities and remote from transportation facilities, require large amount of material. In order to cope with the need of sand, people uses natural trass which are plenty to be found in the area. Test and research on its characteristic and strength with its potentials to be used as cement substitution have never been carried out. Lime was taken from Ngampel village, Blora as it is commonly sold in the area. The planned mixture of lime-trass paste was in the effort to obtain the best composition. The weight ratios used were 100%:0%, 80%:20%, 60%:40%, 40%:60%, 20%:80 and 0%:100%. The mortar mixture with cement substitution was 100%, 80%, 60%, 40%, 20% and 0%.The compressive strength of the lime-trash mixture was between 0.000 MPa and 2.545 MPa. The mortar compressive strength achieved was 0.373 MPa - 26.585 MPa. The test results of mortar compressive strength showed that the more cement substitution amount used, the less the compressive strength would be. The mortar compressive strength increased in line to the age of the mortar. The mortar tensile strength obtained was 0.000 MPa - 2.169 MPa. The block compressive strength obtained was 3.336 MPa - 3.403 MPa. Water absorbency of the block was 15.831% -16.056%.
Mix Design of Self Compacting Concrete Based on Ultra High Compressive Strength Flow Mortar Mix Soca Anggoro Wulan; Iman Satyarno; Ashar Saputra
Journal of the Civil Engineering Forum Vol. 4 No. 1 (January 2018)
Publisher : Department of Civil and Environmental Engineering, Faculty of Engineering, UGM

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.22146/jcef.29797

Abstract

Mix design of Self Compacting Concrete or SCC is not straight forward because many parameters control its rheological properties. The case becomes more complicated if high compressive strength is also to be achieved. Therefore simpler approach is used, that is by firstly determining the flow mortar mix which is easier to be designed even with the requirement of ultra-high compressive strength. The mix design of SCC is then determined by simply adding the coarse aggregate with a certain amount of that mortar mix. In this research the ultra-high compressive strength flow mortar was made of Type I cement, 15% of cement weight silica fume, weight ratio of cement and curve No IV sand was 1: 0.35. The water-cementious ratio was 0.22 and the amount of plasticizer was 1.3%, 1.4%, 1.5% and 1.6% of the cement weight. For the SCC, the used coefficient was taken to be 1.4, 1.6, and 1.8 of the volume of that aggregate void for mortars, the aggregate value was at the volume of the remaining count of mortar and its size was 4.8 mm - 9.6 mm. Test results show that the mortar flow ability was 170 mm, 180 mm, 220 mm and 250 mm, where the achieved compressive strength was 83.1 MPa, 96.8 MPa, 111.4 MPa, and 135.5 MPa respectively. Mortar mix with 1.6% super plasticizer was then used for making the SCC and the results show that the concrete flow were 460 mm, 580 mm and 660 mm and the compressive strength were 88.2 MPa, 100.0 MPa, and 97.9 MPa.  It can be concluded that using this simpler approach the SCC can have 580 mm flow and 100 MPa compressive strength
Co-Authors Ashar Saputra Muhammad Nurzain Muslikh Muslikh Soca Anggoro Wulan