Claim Missing Document
Check
Articles

Found 7 Documents
Search

Perbandingan Desain Dermaga Terapung Pada Sistem Konstruksi Melintang dan Memanjang “Studi Kasus Dermaga Pelabuhan Tideng Pale Kabupaten Tana Tidung” Utomo, Edy
Borneo Engineering : Jurnal Teknik Sipil Volume 2, Nomor 1, Juni 2018
Publisher : Jurusan Teknik Sipil

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1011.762 KB) | DOI: 10.35334/be.v2i1.607

Abstract

Floating port is a barge made of rectangular steel or concrete that can float to adjust the water lavel. Barge is a cargo ship type do not have a propulsion system. So, design of floating port preferably aqual to ship design. There are 3 types of barge construction system, that are longitudinal system, transversal system and mixed construction. To get the optimal design of floating port, comparison of design based on the construction system is needed. Case study in this research ia a Tideng Pale-KTT floating port. Deformation and stress analysis using FEA method on 2 models of construction system, that are transversal and longitudinal. Based on results, both of construction system produce a good strength value. However, there are some construction component which does not match the placement of the construction system. Results of construction costs have 5,51% deviation, longitudinal sytem is more expensive. So, produce the hypotheses to do a combination for both of construction systems.
Kajian Kinerja Bagian Jalinan (Studi Kasus : Jl. Niaga 1 – Jl. Yos Sudarso, Kota Tarakan) Syarif, Iif Ahmad; Prasetya, Noerman Adi; Aidil, Rahmad; Faizal, Rahmat; Utomo, Edy; Hernadi, Ahmad
Borneo Engineering : Jurnal Teknik Sipil Volume 1, Nomor 2, Desember 2017
Publisher : Jurusan Teknik Sipil

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (494.145 KB) | DOI: 10.35334/be.v1i2.597

Abstract

This study aims to determine the performance on a single weave that occurred on Jl.Niaga I - Jl. Yos Sudarso, Tarakan City. The performance is capacity, degree of saturation, speed, and travel time. With these performance parameters serve as based of planning in transportation infrastructure. The results of this study are also expected to provide recommendations to users, planners and policy makers in an effort to solve traffic problems, especially to reduce the delay that occurs in a single wave that occurred on Jl Niaga I-Jl. Yos Sudarso Kota Tarakan.
Kajian Aplikasi Robot dalam Industri Perkapalan Utomo, Edy
Wave: Jurnal Ilmiah Teknologi Maritim Vol 9, No 1 (2015)
Publisher : Wave: Jurnal Ilmiah Teknologi Maritim

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (401.947 KB) | DOI: 10.29122/jurnalwave.v9i1.2663

Abstract

Paper ini membahas tentang aplikasi sistem robot dalam proses pembangunan kapal. Aplikasi yang ditinjau untuk pekerjaan welding, blasting dan painting, baik untuk struktur terbuka atau struktur tertutup (double hull). Beberapa kelebihan dan kekurangan pada aplikasi robot akan dibahas untuk mengembangkan aplikasi penggunaan robot yang sudah ada, salah satunya adalah dengan menggunakan konsep humanoid. Studi ini juga mengusulkan beberapa modifikasi aplikasi robot yang sudah ada dalam pembangunan kapal. Hasil dari usulan konsep membutuhkan studi analisis lanjut baik mengenai struktural mekanik pada body robot maupun kajian sistem yang lebih tepat untuk diterapkan.
Sandwich Panel Manufacturing Method In Form of Test Specimens For Ship Construction Utomo, Edy; Zubaydi, Achmad; Budipriyanto, Agung
Wave: Jurnal Ilmiah Teknologi Maritim Vol 11, No 1 (2017)
Publisher : Wave: Jurnal Ilmiah Teknologi Maritim

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29122/jurnalwave.v11i1.2194

Abstract

Sandwich panel as a composite materials require special method of manufacture, to produce the best of physical condition. This study give the manufacturing process of sandwich panel for the purpose of testing the strength of material. Sandwich panel created with molding method for simplify the process of work and can be repeated if a failure occurs. Saveral failures occur in creating process until preparation specimen process that are influenced by saveral things, such as damage caused by the temperature of the sun, difference in viscosity between the layers of the conditions faceplate (smooth and rough), and the method of cutting the sandwich panel which requires cutting methods at low temperatures and does not produce the high vibration to avoid damage to the material before material strength test were performed.
PENGGUNAAN SANDWICH PLATE SYSTEM (SPS) PADA KONSTRUKSI INNER BOTTOM Baidowi, Ahmad; Utomo, Edy; D.K, Fiqih; Indria, Hery
Kapal: Jurnal Ilmu Pengetahuan dan Teknologi Kelautan Vol 12, No 2 (2015): Juni
Publisher : Department of Naval Architecture - Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1401.702 KB) | DOI: 10.14710/kpl.v12i2.8348

Abstract

Perkembangan teknologi yang semakin maju memberikan alternatif-alternatif dalam memperbaiki berbagai bentuk sistem, termasuk di dalamnya konstruksi struktur kapal. Latar belakang dari penelitian ini adalah pada permasalahan kebutuhan material ringan pada kapal, kecepatan proses produksi, penyederhanaan konstruksi dan biaya perawatan kapal yang rendah. Penggunaan material ringan Sandwich Plate System (SPS) menjadi salah satu jawaban dari permasalahan-permasalahan tersebut, penggunaan SPS dapat menyederhanakan bentuk dari konstruksi kapal dengan menghilangkan penegar inner bottom longitudinal dan mampu mengurangi Light Weight Tonnase (LWT). Artikel ini membahas perbandingan pola distribusi tegangan dan deformasi pada konstruksi bottom yang menggunakan SPS dan baja AH36, selain dari itu juga mengetahui seberapa besar pengurangan LWT yang dihasilkan untuk meningkatkan Payload kapal. Analisa dilakukan dengan simulasi numerik berdasarkan FEM pada konstruksi inner bottom dengan pembebanan muatan. Dari hasil simulasi didapatkan besar tegangan maksimal untuk material baja AH36 sebesar 226 Mpa dengan menggunakan penegar, sedangkan konstuksi dengan material SPS tegangan maksimal yang dihasilkan sebesar 221 Mpa tanpa penggunaan penegar, dengan deformasi maksimal untuk AH36 dan SPS yaitu 77 mm yang terjadi pada bagian tengah blok konstruksi inner bottom. Dengan hilangnya penegar berat konstruksi berkurang sebesar 13,05% dari penggunaan material baja AH36 sehingga memberikan peningkatan payload sebesar 13,05%. Simulasi penelitian dilakukan pada kapal Bulk Carrier (BC).
SANDWICH PANEL MANUFACTURING METHOD IN FORM OF TEST SPECIMENS FOR SHIP CONSTRUCTION Utomo, Edy; Zubaydi, Achmad; Budipriyanto, Agung
Wave: Jurnal Ilmiah Teknologi Maritim Vol 11, No 1 (2017)
Publisher : Badan Pengkajian dan Penerapan Teknologi

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29122/jurnalwave.v11i1.2194

Abstract

Sandwich panel as a composite materials require special method of manufacture, to produce the best of physical condition. This study give the manufacturing process of sandwich panel for the purpose of testing the strength of material. Sandwich panel created with molding method for simplify the process of work and can be repeated if a failure occurs. Saveral failures occur in creating process until preparation specimen process that are influenced by saveral things, such as damage caused by the temperature of the sun, difference in viscosity between the layers of the conditions faceplate (smooth and rough), and the method of cutting the sandwich panel which requires cutting methods at low temperatures and does not produce the high vibration to avoid damage to the material before material strength test were performed.
KAJIAN APLIKASI ROBOT DALAM INDUSTRI PERKAPALAN Utomo, Edy
Wave: Jurnal Ilmiah Teknologi Maritim Vol 9, No 1 (2015)
Publisher : Badan Pengkajian dan Penerapan Teknologi

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (401.947 KB) | DOI: 10.29122/jurnalwave.v9i1.2663

Abstract

Paper ini membahas tentang aplikasi sistem robot dalam proses pembangunan kapal. Aplikasi yang ditinjau untuk pekerjaan welding, blasting dan painting, baik untuk struktur terbuka atau struktur tertutup (double hull). Beberapa kelebihan dan kekurangan pada aplikasi robot akan dibahas untuk mengembangkan aplikasi penggunaan robot yang sudah ada, salah satunya adalah dengan menggunakan konsep humanoid. Studi ini juga mengusulkan beberapa modifikasi aplikasi robot yang sudah ada dalam pembangunan kapal. Hasil dari usulan konsep membutuhkan studi analisis lanjut baik mengenai struktural mekanik pada body robot maupun kajian sistem yang lebih tepat untuk diterapkan.