Article Per Year (5 Year)
p-Index From 2019 - 2024
0
P-Index
This Author published in this journals
All Journal Telaah Teknologi Indonesia
Anggito P. Tetuko, Anggito P.
Unknown Affiliation
Computer Science & IT Physics

Published : 2 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 2 Documents
Search

 1 
REMANENSI DAN FLUX DENSITY DARI BERBAGAI BENTUK GEOMETRI MAGNET PERMANEN Nurdiyansyah, Lukman Faris; Tetuko, Anggito P.; Aryanto, Didik; Sebayang, Perdamean
Telaah Vol 32, No 1 (2014)
Publisher : Research Center for Physics

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14203/tel.32.1.176

Abstract

dari berbagai bentuk geometri magnet permanen berbasis ferrite (BaFe12O19) dan logam tanah jarang (NdFeB). Nilai remanensi magnet (Br) diperoleh dari kurva histerisis (B-H curve) yang diukur dengan alat permagraph dan flux density Bz diukur secara langsung dengan menggunakan gaussmeter. Bentuk geometri dan jenis sampel uji adalah cube, ring, dan disk dari magnet permanen berbasis NdFeB dan BaFe12O19. Dari hasil penelitian diketahui bahwa magnet permanen berbasis NdFeB memiliki nilai remanensi yang lebih besar dibanding dengan magnet permanen berbasis BaFe12O19. Dari pengukuran magnet permanen berbasis BaFe12O19 didapatkan nilai Br = 1:17 kG untuk bentuk geometri ring dan untuk disk didapat sebesar Br = 1:78 kG, sedangkan dari magnet permanen berbasis NdFeB yang berbentukcube (tipe 1), cube tipe 2, dan disk didapatkan nilai Br = 7:5 kG, Br = 10:8 kG, dan Br = 5:2 kG. Untuk pengukuran flux density Bz sebagai fungsi jarak z didapatkan kesesuaian antara eksperimen dan teori. Berdasarkan hasil penelitian didapatkan bahwa nilai Br dan Bz sangat dipengaruhi oleh bentuk geometri dan jenis magnet permanen.
99 PEMBUATAN BAHAN FILTER KERAMIK BERPORI BERBASIS ZEOLIT ALAM DAN ARANG SEKAM PADI Sebayang, P.; Muljadi, -; Tetuko, Anggito P.
Teknologi Indonesia Vol 32, No 2 (2009)
Publisher : LIPI Press

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14203/jti.v32i2.9

Abstract

The porous ceramics filter material have been made from natural zeolit and rice husk charcoal with composition variation (in % of mass). The preparation of zeolit was done using ball mill for 24 hours and rice husk charcoal was prepared using vibrating mill for 1 hour until it can be through out in 100 mesh shieve. The two raw materials about 2 grams were mixed with addition 50 ml of Polivinylalcohol (PVA), then it was mixed again until homogeny. The sample was dried pressed with pressure of 25 kgf/cm and dried in a drying oven at 60 C for 24 hours. The sintering process was done using electrical furnace with heating rate of 10C/minute until it reached temperature of 900 and 1000 C, and holded for 2 hours. From the result of porouc ceramics filter material, the optimum composition is 40% rice husk coke + 60% Zeolit with sintering temperature = 1000 C. At this condition, the properties are density = 2,16 g/cm, shrinkage = 35,94%, porosity = 66,05%, water absorption = 31,10%, modulus of rupture = 7,47 MPa, compressive strength = 4,38 MPa, and coefficient of thermal expansion = 5 x 10 -6 C-1. The result of XRD shows that zeolit has major phase of mordenite (Na8[Al8Si40O96].24H2O) and minor phase of clinoptilolite (Na6[Al6Si36O72].24H2O). The result of XRD on 40% rice husk coke + 60% Zeolit and sintering temperature = 1000 C shows that the major phase is mullite (3Al2O3SiO2) and the minor phase is tridimite (SiO2). Meanwhile, the picture of SEM shows that porous ceramics have irregular particle with size between 110 ?m and its pore size can reaches 20 ?m.
Co-Authors Didik Aryanto Lukman Faris Nurdiyansyah, Lukman Faris Muljadi, - Perdamean Sebayang Sebayang, P.