cover
Contact Name
Leni Rumiyanti
Contact Email
lenirumiyanti@fmipa.unila.ac.id
Phone
-
Journal Mail Official
lenirumiyanti@fmipa.unila.ac.id
Editorial Address
-
Location
Kota bandar lampung,
Lampung
INDONESIA
Jurnal Teori dan Aplikasi Fisika
Published by Universitas Lampung
ISSN : 2303016X     EISSN : 25491156     DOI : -
Core Subject : Science,
Jurnal ini diterbitkan oleh Jurusan Fisika Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Lampung sebagai sarana untuk mempublikasikan hasil penelitian, artikel review dari peneliti-peneliti di bidang fisika teori dan aplikasinya. Jurnal ini terbit dua kali setahun (Januari dan Juli).
Arjuna Subject : -
Articles 332 Documents
Realisasi Alat Ukur Indeks Bias Minyak Goreng Kelapa Sawit Menggunakan Sensor Optik Berbasis Mikrokontroler ATmega8535 Arum Masitoh; W Warsito; Akhmad Dzakwan
Jurnal Teori dan Aplikasi Fisika Vol 2, No 1 (2014): Jurnal Teori dan Aplikasi Fisika
Publisher : Universitas Lampung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.23960/jtaf.v2i1.1256

Abstract

Telah direalisasikan sebuah alat pengukur indeks bias minyak goreng dengan menerapkan hukum Snellius dengan tampilan pada komputer. Alat tersebut terdiri dari sensor LDR, mikrokontroler ATMega 8535 dan komputer. Proses kerja alat yaitu cahaya laser akan menembus sampel dan sensor LDR akan menerima berkas cahaya paling terang dari sinar laser yang telah dibiaskan oleh cairan. Ketika sensor LDR terkena cahaya, maka sensor LDR akan memproses tegangan dan mikrokontroler akan membaca keluaran yang dihasilkan oleh sensor LDR tersebut dan kemudian langsung ditampilkan pada komputer. Keluaran dari LDR ini akan dikonversikan menggunakan program sebagai nilai indeks bias cairan. Hasil dari perubahan nilai indeks bias terhadap setiap sampel berbeda-beda dimana pada setiap sampel memiliki perubahan nilai indeks bias yang berbeda pula. Oleh karena itu, alat ini baik digunakan untuk menampilkan nilai indeks bias untuk semua jenis minyak goreng yang mampu dilewati cahaya tampak (transparan).
Pengaruh Variasi HCl Pada Pemurnian Silika Berbasis Batu Apung Jayanti Pusvitasari; Posman Manurung; Pulung Karo Karo
Jurnal Teori dan Aplikasi Fisika Vol 6, No 1 (2018): Jurnal Teori dan Aplikasi Fisika
Publisher : Universitas Lampung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.23960/jtaf.v6i1.1833

Abstract

Silica from pumice natural rock was extracted by varying HCl of 1M and 2M. Fristly, pumice was heated to 400°C for 4 hours to activate the component of material.Three steps were used in obtaining pure silica. Silica extraction by using NaOH, silica titration by using H2SO4, and purification silica with HCl. The purified powder was calcined at 800°C. The characterization of XRD (X-Ray Diffraction) and SEM-EDS (Scanning Elektron Microscopy - Energy Dispersive Spectrometry) were performed for samples after and before purification to know the phase structure and microstructure and pumice powder content. The XRD results was show diffraction pattern of the amorphous shaped SiO2 with some crystalline peaks is an other oxide compound than SiO2 for the starting material, and an anorite crystal phase in the HCl 1M and 2M variations. This is confirmed by EDS results what showing the silica content has the highest percentage of 65.88% for the raw material, 67.83% for HCL 1M and 69.63% for HCl 2M variation after purification. While the SEM results identified the microstructure for the raw material has a clear but not entirely homogeneous that is the identification of the sample in an amorphous state, whereas the sample after purification of the microstructural result shows non-homogeneous grain size, unclear grain boundary boundaries and an algomeration (agglomeration ) which is also the identification of the sample in an amorphous state.Silica from pumice natural rock was extracted by varying HCl of 1M and 2M. Fristly, pumice was heated to 400°C for 4 hours to activate the component of material.Three steps were used in obtaining pure silica. Silica extraction by using NaOH, silica titration by using H2SO4, and purification silica with HCl. The purified powder was calcined at 800°C. The characterization of XRD (X-Ray Diffraction) and SEM-EDS (Scanning Elektron Microscopy - Energy Dispersive Spectrometry) were performed for samples after and before purification to know the phase structure and microstructure and pumice powder content. The XRD results was show diffraction pattern of the amorphous shaped SiO2 with some crystalline peaks is an other oxide compound than SiO2 for the starting material, and an anorite crystal phase in the HCl 1M and 2M variations. This is confirmed by EDS results what showing the silica content has the highest percentage of 65.88% for the raw material, 67.83% for HCL 1M and 69.63% for HCl 2M variation after purification. While the SEM results identified the microstructure for the raw material has a clear but not entirely homogeneous that is the identification of the sample in an amorphous state, whereas the sample after purification of the microstructural result shows non-homogeneous grain size, unclear grain boundary boundaries and an algomeration (agglomeration ) which is also the identification of the sample in an amorphous state.
Efek Frekuensi Gelombang Ultrasonik Terhadap Mikroba Pada Air Kaldu Daging Sapi Novia Puspasari; Arif Surtono; W Warsito
Jurnal Teori dan Aplikasi Fisika Vol 2, No 2 (2014): Jurnal Teori dan Aplikasi Fisika
Publisher : Universitas Lampung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.23960/jtaf.v2i2.1272

Abstract

Telah dilakukan penelitian efek frekuensi gelombang ultrasonik (US) terhadap mikroba pada air kaldu daging sapi dengan variasi frekuensi 40 kHz, 50 kHz, dan 60 kHz dan variasi lama perlakuan 2 jam, 4 jam, 6 jam dan 8 jam dengan daya pembangkit gelombang ultrasonik 30 watt. Penelitian ini bertujuan untuk mengetahui tingkat kejernihan dan jumlah mikroba pada air kaldu daging sapi yang diberi perlakuan gelombang ultrasonik dengan yang tidak diberi perlakuan gelombang ultrasonik. Tingkat kejernihan air kaldu daging sapi dilihat dengan menggunakan metode grayscale, air kaldu daging sapi dengan perlakuan gelombang ultrasonik lebih jernih dibandingkan dengan tanpa perlakuan. Jumlah mikroba pada air kaldu daging sapi dengan perlakuan gelombang ultrasonik lebih sedikit dibandingkan air kaldu daging sapi tanpa perlakuan gelombang ultrasonik dengan variasi waktu 2 jam, 4 jam, 6 jam dan 8 jam.
Sensor Kebocoran Arus Listrik Water Heater Elektrik Hartono Hartono; Sugito Sugito; Farzand Abdullatif
Jurnal Teori dan Aplikasi Fisika Vol 6, No 2 (2018): Jurnal Teori dan Aplikasi Fisika
Publisher : Universitas Lampung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.23960/jtaf.v6i2.1504

Abstract

An electric current sensor detecting current leak into water flowing out from a water heater has been constructed. The sensor is made of a copper electrode implanted in a PVC pipe. It is subjected to tests in which the voltage is varied at constant resistance and otherwise the resistance is varied at constant voltage. The variation of the AC voltage is conducted from 0 to 220 volt whereas that of the resistance is from 1 KW to 100 KW. The 1 KW resistance is meant to represent the resistance of human skin in wet condition and the 100 KW represents that of dry insulated skin. Analysis shows that unpainful shock sensation surges at 30 V, 5.16 mA, with 1 KW resistance. In  the current leak condition at 220 V, unpainful shock is sensed at body resistance of 42 KW with 4,99 mA current.
Maintaining Quality Control by Using General Radiological Film Rini Safitri; Evi Yufita
Jurnal Teori dan Aplikasi Fisika Vol 3, No 1 (2015): Jurnal Teori dan Aplikasi Fisika
Publisher : Universitas Lampung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.23960/jtaf.v3i1.1289

Abstract

Telah dilakukan pengujian karakteristik film radiografi untuk menentukan kualitas citra film radologi dengan cara melakukan kegiatan Quality Control (QC) pada mesin sinar X. Salah satu parameter yang mempengaruhi citra film tersebut adalah dosis sinar X yang diterima pasien dalam setiap penyinaran dan juga untuk memastikan keamanan pada pasien pada saat pemeriksaan penyakit serta memastikan mesin sinar X dapat beroperasi secara optimal. Kegiatan QC pencitraan film Rontgen ini dilakukan dengan dua cara pengukuran yaitu menggunakan sensitometer untuk melihat kualitas citra film dan densitometer untuk melihat densitas cahaya yang dihasilkan melalui film radiografi. Dari hasil penelitian diperoleh bahwa film radiografi dengan merek AGFA layak digunakan karena daerah fog nya tidak melebihi batas toleransi yaitu 0.01 OD, dan daerah shoulder menghasilkan densitas maksimum yaitu 2,25 OD dimana daerah ini masih dapat dianalisa.
Pengaruh Temperatur terhadap Karakterisasi Klinker Semen dengan Substitusi 20% Batu Basalt terhadap Massa Batu Kapur dan 20% Batubara terhadap Massa Total sebagai Reduktor Leni Rumiyanti; Yuliana Sari; Muhammad Amin
Jurnal Teori dan Aplikasi Fisika Vol 7, No 1 (2019): Jurnal Teori dan Aplikasi Fisika
Publisher : Universitas Lampung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.23960/jtaf.v7i1.2141

Abstract

This study was conducted to determine the effect of temperature on the chemical content and crystal structure on clinker of cement with 20% substitution of basalt stone on the mass of limestone and 20% of coal against total mass. The raw material used is basalt stone from East Lampung and anthracite coal. The percentage of limestone used is 80%. All raw materials are milled, sifted, then formed pellets with a diameter of 0.8 - 1.4 cm. Pellets are dried at room temperature, then heated and burned with temperature variations of 1000 ° C, 1100 ° C and 1200 ° C for 1 hour. XRF results showed that basalt rock had a content of SiO2 + Al2O3 + Fe2O3 of 79.293% so that basalt could be said to have pozzolanic properties. The CaO content for cement clinker decreased, the results of XRF with combustion temperatures of 1000 ° C, 1100 ° C and 1200 ° C respectively were 62,329%, 55,606%, and 54,148%. Materials A, B and C respectively were burning at 1000°C, 1100°C, and 1200oC for 1 hour. The crystalline phase formed in material A is calcium iron oxide with the highest peak belonging to Ca at position 2θ which is 26.6627° and another crystal phase, gehlenite, syn. The crystalline phase formed in material B is akermanite-gehlenite syn with the highest peak belonging to Ca at position 2θ which is 31.2747° and other crystalline phases namely and wollastonite, ferroan 1A. While the crystalline phase formed in material C is akermanite-gehlenite with the highest peak belonging to Ca at position 2θ which is 31.3051° and syn and other crystalline phases namely wollastonite, ferroan 1A.
Desain dan Realisasi Sistem Telemetri Getaran dengan Media Transmisi HT Menggunakan Sensor Accelerometer MMA7361 Berbasis Mikrokontroler ATMega8535 Gurum Ahmad Pauzi; Meta Dia Febriska; Amir Supriyanto
Jurnal Teori dan Aplikasi Fisika Vol 3, No 2 (2015): Jurnal Teori dan Aplikasi Fisika
Publisher : Universitas Lampung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.23960/jtaf.v3i2.1307

Abstract

Telah direalisasikan sistem telemetri getaran dengan media transmisi HT yang menggunakan sensor accelerometer MMA7361 berbasis mikrokontroler ATMega8535. Tujuan penelitian adalah membuat sistem pendeteksi gempa bumi sederhana. Penelitian dilakukan dengan meletakan sensor accelerometer di atas speaker yang diberikan frekuensi dari signal generator, dianggap sebagai getaran gempa bumi buatan. Frekuensi diberikan bervariasi dari 0,5Hz s.d. 20Hz diambil selama 400s. Hasil pengujian FFT dengan filter Savitzky-Golay, frekuensi dominan sumbu X adalah 0,66265Hz dengan magnitudo 8,6871dB untuk, pada sumbu Y frekuensi dominan adalah 0,66934Hz dengan magnitudo 10,6789dB dan pada sumbu Z frekuensi dominan adalah 0,64678Hz dengan magnitudo 13,3095dB. Data hasil penelitian dianalisis dan diperoleh standar deviasi pada sistem telemetri untuk sumbu X adalah 0,2313 V, untuk sumbu Y adalah 0,4954 V dan untuk sumbu Z 0,0198 V.
Analisis Pengaruh Tekanan Pada Serat Optik Terhadap Sistem Transmisi Data BerbasisMikrokontroler ATMega32 Dengan Akuisisi Data Menggunakan Matlab Rita Budiati; Gurum Ahmad Pauzi; W Warsito
Jurnal Teori dan Aplikasi Fisika Vol 4, No 1 (2016): Jurnal Teori dan Aplikasi Fisika
Publisher : Universitas Lampung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.23960/jtaf.v4i1.1324

Abstract

Telah dilakukan penelitian mengenai pengaruh tekanan pada serat optik terhadap sistem transmisi data. Pengaruh tekanan pada serat optik ini lebih dikenal dengan mikrobending. Mikrobending menyebabkan terjadinya deformasi pada inti serat optik dan mengakibatkan berkurangnya daya optik yang melalui serat optik. Penelitian ini meliputi pengujian kestabilan laser, pengaruh tekanan dan elastisitas serat optik. Pengujian ini menggunakan sensor fototransistor, serat optik single mode, laser dengan panjang gelombang 650 nm, catu daya, sistem minimum mikrokontroler ATMega32, rangkaian penguat IC324, dan software Matlab. Tekanan yang diberikan berasal dari variasi beban dengan massa antara 0 sampai 8 kg.Variasi beban diletakkan di atas serat optik secara terpusat. Hasil penelitian menunjukkan bahwa kestabilan laser cukup baik, ketika variasi beban diletakkan di atas serat optik, maka sinar laser yang diterima semakin kecil. Oleh karena itu, sinar laser yang diterima semakin kecil, maka tegangannya akan semakin kecil juga. Hal ini ditunjukkan dengan penurunan grafik seiring bertambahnya beban yang diletakkan di atas serat optik dan serat optik menunjukkan elastisitas yang cukup baik.
Analisis Dimensi Fraktal Sinyal Elektrokardiografi Rizki Yara Narvinda; Arif Surtono; A Amanto
Jurnal Teori dan Aplikasi Fisika Vol 5, No 1 (2017): Jurnal Teori dan Aplikasi Fisika
Publisher : Universitas Lampung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.23960/jtaf.v5i1.1362

Abstract

It has been utilized a research on the fractal dimension analysis of electrocardiographic (ECG) signals. ECG signal is one example of a fractal nature, so that this signal can be calculated using fractal dimension. The purpose of this study calculates the ECG signal by using fractal dimension. Calculation of fractal dimension is processed using matlab 7.8 software with a sampling of the ECG signal on the website www.physionet.org. Fractal dimension method used is the Box-Counting. Classification of signal samples are taken, there are two types: normal and arrhythmia. The results of the dimension values obtained MIT-BIH database Normal Sinus Rhythm is 1.37; MIT-BIH database arrhythmias is 1.49; MIT-BIH database Supraventri arrhythmias is 1.44; and Cu ventricular tachyarrhythmia is 1.21. From these data it can be concluded that the classification dimension values in the range between 1-2 is in a state of cardiac arrhythmias and classification dimension values in a normal state has a value equal to one dimension.
Sistem Otomasi Kincir Air Untuk Respirasi Udang Tambak Menggunakan Sensor Dissolved Oxygen (DO) Ari Fiyanti; Warsito Warsito; Sri Wahyu Suciyati
Jurnal Teori dan Aplikasi Fisika Vol 5, No 2 (2017): Jurnal Teori dan Aplikasi Fisika
Publisher : Universitas Lampung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.23960/jtaf.v5i2.1811

Abstract

Automation system waterwheel for farmed shrimp respiration have realized using dissolved oxygen sensors (DO). The DO sensor used to detect the levels of dissolved oxygen in the water. Digital data output sensor DO is connected to the computer via the arduino uno, furthermore the output data are recorded and displayed on the LCD monitor and a television series. Automation system using relay with a range of dissolved oxygen levels <4,00 mg/L for the condition of the windmills ON and >5,50 mg/L for the condition of the windmills OFF.

Page 5 of 34 | Total Record : 332


Filter by Year

2013 2024


Filter By Issues
All Issue Vol 12, No 1 (2024): Jurnal Teori dan Aplikasi Fisika Vol 11, No 2 (2023): Jurnal Teori dan Aplikasi Fisika Vol 11, No 1 (2023): Jurnal Teori dan Aplikasi Fisika Vol 10, No 1 (2022): Jurnal Teori dan Aplikasi Fisika Vol 9, No 2 (2021): Jurnal Teori dan Aplikasi Fisika Vol 9, No 1 (2021): Jurnal Teori dan Aplikasi Fisika Vol 8, No 2 (2020): Jurnal Teori dan Aplikasi Fisika Vol 8, No 1 (2020): Jurnal Teori dan Aplikasi Fisika Vol 7, No 2 (2019): Jurnal Teori dan Aplikasi Fisika Vol 7, No 1 (2019): Jurnal Teori dan Aplikasi Fisika Vol 7, No 1 (2019): Jurnal Teori dan Aplikasi Fisika Vol 6, No 2 (2018): Jurnal Teori dan Aplikasi Fisika Vol 6, No 2 (2018): Jurnal Teori dan Aplikasi Fisika Vol 6, No 1 (2018): Jurnal Teori dan Aplikasi Fisika Vol 6, No 1 (2018): Jurnal Teori dan Aplikasi Fisika Vol 5, No 2 (2017): Jurnal Teori dan Aplikasi Fisika Vol 5, No 2 (2017): Jurnal Teori dan Aplikasi Fisika Vol 5, No 1 (2017): Jurnal Teori dan Aplikasi Fisika Vol 5, No 1 (2017): Jurnal Teori dan Aplikasi Fisika Vol 4, No 2 (2016): Jurnal Teori dan Aplikasi Fisika Vol 4, No 2 (2016): Jurnal Teori dan Aplikasi Fisika Vol 4, No 1 (2016): Jurnal Teori dan Aplikasi Fisika Vol 4, No 1 (2016): Jurnal Teori dan Aplikasi Fisika Vol 3, No 2 (2015): Jurnal Teori dan Aplikasi Fisika Vol 3, No 2 (2015): Jurnal Teori dan Aplikasi Fisika Vol 3, No 1 (2015): Jurnal Teori dan Aplikasi Fisika Vol 2, No 2 (2014): Jurnal Teori dan Aplikasi Fisika Vol 2, No 2 (2014): Jurnal Teori dan Aplikasi Fisika Vol 2, No 1 (2014): Jurnal Teori dan Aplikasi Fisika Vol 2, No 1 (2014): Jurnal Teori dan Aplikasi Fisika Vol 1, No 2 (2013): Jurnal Teori dan Aplikasi Fisika Vol 1, No 1 (2013): Jurnal Teori dan Aplikasi Fisika More Issue