cover
Contact Name
-
Contact Email
-
Phone
-
Journal Mail Official
-
Editorial Address
-
Location
Kota yogyakarta,
Daerah istimewa yogyakarta
INDONESIA
Bulletin of Electrical Engineering and Informatics
ISSN : -     EISSN : -     DOI : -
Core Subject : Engineering,
Bulletin of Electrical Engineering and Informatics (Buletin Teknik Elektro dan Informatika) ISSN: 2089-3191, e-ISSN: 2302-9285 is open to submission from scholars and experts in the wide areas of electrical, electronics, instrumentation, control, telecommunication and computer engineering from the global world. The journal publishes original papers in the field of electrical, computer and informatics engineering.
Arjuna Subject : -
Articles 11 Documents
Search results for , issue "Vol 4, No 4: December 2015" : 11 Documents clear
Reconfiguration with Simultaneous DG installation to Improve the Voltage Profile in Distribution Network using Harmony Search Algorithm S Muqthiar Ali; P Suresh Babu; B Gurusekhar
Bulletin of Electrical Engineering and Informatics Vol 4, No 4: December 2015
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1053.229 KB) | DOI: 10.11591/eei.v4i4.509

Abstract

Due to dynamic nature of loads, total system load is more than its generation capacity that makes relieving of load on the feeders not possible and hence voltage profile of the system will not be improved to the required level. In order to meet required level of load demand, Reconfiguration and DG units are integrated in distribution network to improve voltage profile, to provide reliable and uninterrupted power supply and also to achieve economic benefits such as minimum power loss, energy efficiency and load leveling. This work proposes minimization of real power losses and improvement of voltage profile using network reconfiguration in the presence of distributed generation. Generally distributed generations (DG) are preferred with objective of minimizing real power loss and improving voltage profile in distribution system. In this work A meta heuristic Harmony Search Algorithm (HSA) is used to simultaneously reconfigure and identify the optimal locations for installation of DG units in a distribution network. Sensitivity analysis is used to identify optimal locations for installation of DG units. The proposed method has tested in MATLAB for 33-bus and 69- Bus radial distribution systems at three different load levels and the analysis is presented for loss minimization.
NCTF-FL Controller for Pendulum Balancing System Noor Hisham Jalani
Bulletin of Electrical Engineering and Informatics Vol 4, No 4: December 2015
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (290.572 KB) | DOI: 10.11591/eei.v4i4.549

Abstract

Pendulum Balancing of Linear Servo System consists of a cart driven by a DC motor, via a rack and pinion mechanism to ensure consistent and continuous traction. The cart is also equipped with a rotary joint to which a free turning rod (or pendulum) can be attached. This concept paper proposed a combination of Nominal Characteristic Trajectory Following (NCTF) and Fuzzy Logic (FL) to control the position of the cart and to balance the pendulum. The proposed controllers are expected to have a simple design method and achieved high performances.  
Location-Based Services and Privacy Protection under Mobile Cloud Computing Yan Yan; Hao Xiaohong; Wang Wanjun
Bulletin of Electrical Engineering and Informatics Vol 4, No 4: December 2015
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (356.106 KB) | DOI: 10.11591/eei.v4i4.548

Abstract

Location-based services can provide personalized services based on location information of moving objects and have already been widely used in public safety services, transportation, entertainment and many other areas. With the rapid development of mobile communication technology and popularization of intelligent terminals, there will be great commercial prospects to provide location-based services under mobile cloud computing environment. However, the high adhesion degree of mobile terminals to users not only brings facility but also results in the risk of privacy leak. The paper introduced the necessities and advantages to provide location-based services under mobile cloud computing environment, stressed the importance to protect location privacy in LBS services, pointed out new security risks brought by mobile cloud computing, and proposed a new framework and implementation method of LBS service. The cloud-based LBS system proposed in this paper is able to achieve privacy protection from the confidentiality of outsourced data and integrity of service results, and can be used as a reference while developing LBS system under mobile cloud computing environment.
A Hybrid Methodology for Performance Assessment of Campus Network Li Mao; De-yu Qi
Bulletin of Electrical Engineering and Informatics Vol 4, No 4: December 2015
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (126.57 KB) | DOI: 10.11591/eei.v4i4.547

Abstract

In this paper, we propose a combined methodology of fuzzy analytic hierarchy process (FAHP) and data envelopment analysis (DEA) in order to apply it to multivariate analysis and integrated evaluation. With FAHP method, the relative importance levels of different available indicators are determined. And the DEA model is used to obtain the efficiency performances of the use case of network measurement. Finally network performance is evaluated by means of integrating available indicator weights with efficiency performances. It is quite important that the integrated methodology considers both personal preferences and objective relative efficiency for assessment simultaneously to avoid the bias of single methodology.
Characterization of Capacitive Comb-finger MEMS Accelerometers Aaditi Joshi; Sangram Redkar; Thomas Sugar
Bulletin of Electrical Engineering and Informatics Vol 4, No 4: December 2015
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (793.865 KB) | DOI: 10.11591/eei.v4i4.546

Abstract

This paper discusses various methods for testing the performance of MEMS capacitive comb-finger accelerometers manufactured by Sandia National Laboratories. The use of Capacitive MEMS devices requires complex circuits for measurement of capacitance. Sandia MEMS accelerometer’s capacitance changes in a very small femto-farad (fF) range. The performance of accelerometer is tested using Analog Devices AD7747 sigma-delta capacitance to digital converter. The response of a MEMS capacitive accelerometer to various tests is useful for testing and characterization and investigate it’s suitability for various applications
Design of a Class F Power Amplifier With 60% Efficiency at 1800 MHz Frequency Neda Babapour; Javad Javidan
Bulletin of Electrical Engineering and Informatics Vol 4, No 4: December 2015
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/eei.v4i4.515

Abstract

Based on the portable systems application, it is necessary to design blocks with high efficiency to increase battery lifetime. Power amplifier is the highest power consumption block in transmitter. The proposed circuit was simulated using ADS Agilent based on 0.18 μm TSMC RF CMOS technology and supply voltage of 3.3V on transistor level. The proposed power amplifier was designed by Class F type at 1800 MHz with 60% efficiency and output powers of 30 dBm.
ANN Controller Design for Lime Kiln Process Sandeep Kumar Sunori; Pradeep Kumar Juneja
Bulletin of Electrical Engineering and Informatics Vol 4, No 4: December 2015
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1279.925 KB) | DOI: 10.11591/eei.v4i4.514

Abstract

The lime kiln is a very complex multivariable process with severe non linearities, high degree of coupling and frequent disturbances. In this paper a 2x2 lime kiln process with two manipulated variables namely the fuel gas flowrate, and the percent opening of the induced draft damper and two controlled variables namely front end temperature and back end temperature has been considered. After its decoupling, artificial neural network (ANN) controllers have been designed to control the front end temperature. The performance of ANN controllers have been compared with that of conventional controllers.
Invention into the AC Voltage Regulator with V/F Technique for Induction Motor Starting Applications Mahesh Kollipara; V N Srinivasa Rao Kolluru
Bulletin of Electrical Engineering and Informatics Vol 4, No 4: December 2015
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (148.461 KB) | DOI: 10.11591/eei.v4i4.513

Abstract

Modern electrical motors are available in many different forms with different mounting arrangements. To ensure a long life for the motor it is important to select it with correct degree of protection when operating under heavy duty conditions in a severe environment. Smooth starting is also one of major considerations to get long life and optimum efficiency. The conventional method to start an asynchronous motor with a soft starter is by reducing the voltage of the motor by varying the voltage “off time”. The “off time” could for example be controlled to achieve a desired maximum current level or a constant driving torque.  Even if the voltage is reduced the fundamental frequency of the voltage is equal to the supply voltage frequency. That gives a large difference between angular speed of supply voltage and angular speed of the rotor during start. Due to the large difference in angular speed the motor flux will be low and thereby also the ability to produce torque. Instead of using the conventional control method with a reduced voltage it is possible to use a method with controlled flux similar to frequency inverters for soft-starters. As the soft-starter does not have the intermediate DC energy storage the applied voltage vector has to be directly modulated from the mains supply.
Interleaved High Step-up DC-DC Converter with Diode-Capacitor Multiplier Cell and Ripple-Free Input Current Mostafa Jalalian Ebrahimi; Abbas Houshmand Viki Viki
Bulletin of Electrical Engineering and Informatics Vol 4, No 4: December 2015
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (205.496 KB) | DOI: 10.11591/eei.v4i4.512

Abstract

In this paper interleaving and switched-capacitor techniques are used to introduce a high step-up DC-DC converter for renewable energy systems application. The proposed converter delivers high voltage gain without utilizing transformer or excessive duty cycle and features ripple-free input current which results in lower conduction losses and decreased electromagnetic interference (EMI). Lower output capacitance is another advantage of proposed converter, leading to smaller size and lower cost. Furthermore lower voltage stress on switches allows the utilization of switches with low resistance. Simulation results verify the performance of suggested converter.
Analysis of a Bidirectional DC-DC Converter with High Voltage Gain Behrouz Razzaghzadeh; Mahdi Salimi
Bulletin of Electrical Engineering and Informatics Vol 4, No 4: December 2015
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (187.668 KB) | DOI: 10.11591/eei.v4i4.511

Abstract

A novel bidirectional DC-DC converter with high conversion ratio is proposed in this paper. The proposed converter uses the three windings coupled-inductor to achieved high voltage conversion ratio. The primary side consist of a winding and secondary side consist of two windings, which these two windings are series to achieved high voltage gain.In the boost mode, a capacitor is parallel charged and series discharged by the coupled inductor. Thus, high step-up voltage gain can be achieved with an appropriate duty ratio. In the buck mode, a capacitor is series charged and parallel discharged by the coupled inductor. The bidirectional converter can have high step-down voltage gain.The stress voltage of main switches can be reduced, and efficiency can be improved. The operating principle and the steady-state analyses of the voltage gain are discussed. Finally, in 24V for low voltage, and 400V for high voltage, and 200W for output power, this converter is simulated in MATLAB.

Page 1 of 2 | Total Record : 11