cover
Contact Name
Much Sobri Sungkar
Contact Email
elektropower41@gmail.com
Phone
+6285642671665
Journal Mail Official
elektropower41@gmail.com
Editorial Address
Tim Redaksi POWER ELEKTRONIK : JURNAL ORANG ELEKTRO Program Studi D3 Teknik Elektro Politeknik Harapan Bersama Tegal Jl. Dewi Sartika No.71 Kota Tegal Telp. (0283) 350567 Email : powerelektronik.ejournal@poltektegal.ac.id elektropower41@gmail.com
Location
Kota tegal,
Jawa tengah
INDONESIA
Power Elektronik : Jurnal Orang Elektro
ISSN : 23016949     EISSN : 27155064     DOI : 10.30591/polektro.v8i1.
Power Elektronik : Jurnal Orang Elektro, dengan nomor terdaftar ISSN 2301-6949 (print), 2715-5064 (online) adalah jurnal ilmiah yang dikelola oleh Program Studi D3 Teknik Elektronika Politeknik Harapan Bersama dan diterbitkan oleh Pusat Penelitian dan Pengabdian Masyarakat (P3M) Politeknik Harapan Bersama Tegal. Power Elektronik : Jurnal Orang Elektro adalah jurnal peer-review yang diterbitkan dua kali setahun (Januari dan Juli). Power Elektronik : Jurnal Orang Elektro , with registered number ISSN 2301-6949 (print), 2715-5064 (online) is a scientific journal managed by Program Studi D3 Teknik Elektronika Politeknik Harapan Bersama and published by Pusat Penelitian dan Pengabdian Masyarakat (P3M) Politeknik Harapan Bersama Tegal. Power Elektronik : Jurnal Orang Elektro is a peer-reviewed journal published two times a year (January and July).
Articles 175 Documents
Prototype Pendeteksi Tegangan AC Dengan IC 4017 Yoana Nurul Asri; Agung Santoso
Power Elektronik : Jurnal Orang Elektro Vol 10, No 1 (2021): POWER ELEKTRONIK
Publisher : Politeknik Harapan Bersama Tegal

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30591/polektro.v10i1.2325

Abstract

Listrik merupakan kebutuhan penting bagi kehidupan masa kini. Dari banyaknya manfaat, listrik pun menyimpan resiko. Keamanan yang minim dapat saja menimbulkan sengatan listrik. Salah satu alat pendeteksi adanya tegangan listrik yaitu dengan menggunakan tespen. Namun salah satu kelemahan tespen yaitu jika isolator mengalami kerusakan dan dapat tersengat listrik kapan saja, sehingga dibuatlah sebuah alat untuk meminimalisir resiko tersebut dengan mendeteksi tegangan listrik tanpa menyentuh jalur listrik yaitu menggunakan IC 4017 dengan led dan buzzer sebagai outputnya. Terbukti melalui prototype ini dapat mendeteksi adanya tegangan listrik pada penghantar listrik sampai pada rentang maksimum 15 cm dengan fitting lampu dan jangkauan minimum sebesar 6 cm pada KWh meter dan stop kontak.   
Rancang Bangun Interkom Satu Kanal yoana nurul asri; Kevin Pratama Putra
Power Elektronik : Jurnal Orang Elektro Vol 10, No 1 (2021): POWER ELEKTRONIK
Publisher : Politeknik Harapan Bersama Tegal

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30591/polektro.v10i1.2357

Abstract

Kebutuhan komunikasi dalam pesawat terbang merupakan hal yang vital. Rancang bangun interkom satu kanal ini menggunakan komponen IC LM 326 sebagai komponen utamanya. Saat interkom satu mengirimkan sinyal suara dari microphone maka pada interkom 2 akan mendapat output dari sinyal suara tersebut melalui speaker dan sebaliknya. Ketika tombol ditekan, lampu indikator menyala dan input berupa suara yang dimasukan ke microphone akan diperkuat oleh pre-amp microphone dan audio amplifier dan speaker akan mengeluarkan suara sebagai informasi. Hasil uji fungsi menunjukkan bahwa perbandingan tegangan input dan output menghasilkan tegangan yang sama yaitu 12 V dan suara yang dihasilkan jelas antara input dan output.
PERANCANGAN PROTOTIPE LOW COST SMART HOME SYSTEM BERBASIS INTERNET of THINGS Sarosa Castrena Abadi; Givy Devira Ramadani; Mindit Eriyadi
Power Elektronik : Jurnal Orang Elektro Vol 10, No 1 (2021): POWER ELEKTRONIK
Publisher : Politeknik Harapan Bersama Tegal

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30591/polektro.v10i1.2365

Abstract

Abstract  The benefits of technology that can be applied to human problems nowadays one of them is in the process of control and monitoring of resources in a building in a close and in a long distance. The Internet of things are being continuously developed and implemented in all areas, that is because of the needs of devices that can be controlled and monitored remotely. In this study Smart Home System designed to be able to control all equipments in the home with any brand device, then the Smart Home System is able to monitor the state of the Home from the dangerous things such as smoke and gas with the addition of sensor devices that is needed by the user in a home and also with a low power consumption. The process of control and monitoring is done through web interface. The test results show the system can store the remote code for each TV and AC equipment and the code is reused by ESP8266 as a controller to remote all TV equipment and air conditioning with a different brands. In addition test results show the system can monitor and provide notifications through a Web view that can be accessed using a Web browser. Keywords: IOT , ESP8266, Smart , Home , low cost
RANCANG BANGUN ALAT PENGUSIR NYAMUK BERBASIS GELOMBANG ULTRASONIK DAN UV LIGHT TRAP Qirom Qirom; Ulil Albab
Power Elektronik : Jurnal Orang Elektro Vol 10, No 1 (2021): POWER ELEKTRONIK
Publisher : Politeknik Harapan Bersama Tegal

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30591/polektro.v10i1.2373

Abstract

Iklim tropis di Indonesia sangat membantu dalam pertumbuhan nyamuk di mana-mana. Nyamuk dapat menularkan berbagai jenis penyakit antara lain demam berdarah, malaria dan filariasis. Di Indonesia, sekitar 1,62 juta orang terserang malaria dan lebih dari 100.000 orang menderita DB yang diakibatkan oleh nyamuk penular penyakit. Perancangan alat yang digunakan untuk membuat pengusir nyamuk berupa UltraSonik, Lampu UV, Arduino Uno dan Kipas. Fungsi gelombang ultrasonik menggangu keberadaan nyamuk, Lampu UV berkumpul berkumpul, Arduino Uno sebagai perangkat perangkat mikrokontroler dan Kipas agar nyamuk mati putaran kipas.
Analisis Jarak Penggunaan RFID (Radio Frequency Identification) pada Prototipe Smart Home Imam Abdul Rozaq
Power Elektronik : Jurnal Orang Elektro Vol 10, No 1 (2021): POWER ELEKTRONIK
Publisher : Politeknik Harapan Bersama Tegal

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30591/polektro.v10i1.2374

Abstract

Abstract  Smart home is a technology that is used to simplify homework by increasing safety, efficiency and comfort. Security is one of the goals of smart home created, so it needs to be improved starting from the beginning in and out. With the development of smart home technology to improve home security, many tools or sensors are being used, one of which uses RFID or Radio Frequency Identification. Research and Development (RnD) is used in this research, namely by designing, manufacturing, testing products by analyzing the distance that can be used in the use of RFID. The result of this research is that RFID can be used when the distance between the RFID tag and the RFID reader is between 0 cm to 1.4 cm, and this RFID cannot be used when the distance between the RFID tag and the RFID reader is more than 1.6 cmKeywords: smart home, technology, RFID
RANCANG BANGUN ALAT PRES CETAK RENGGINANG OTOMATIS BERBASIS ARDUIN UNO Muchamad Sobri Sungkar; Martselani Adias Sabara
Power Elektronik : Jurnal Orang Elektro Vol 10, No 1 (2021): POWER ELEKTRONIK
Publisher : Politeknik Harapan Bersama Tegal

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30591/polektro.v10i1.2376

Abstract

Teknologi dapat membantu  pekerjaan manusia menjadi lebih mudah, efektif dan efisien. Alat pres cetak rengginang digunakan secara otomatis sehingga tidak memerlukan tenaga manusia dalam membuat hasil cekungan pada rengginang. Alat pres cetak rengginang berfungsi untuk menekan dan memberikan cekungan untuk membentuk rengginang, dengan mengoprasionalkan alat ini semua pekerja dapat melakukakannya walaupuun pekerja belum ahli membuat rengginang. Hal ini sangat berbeda dengan proses pembuatan rengginang secara manual yang hanya dapat di kerjakan oleh pekerja yang tergolong ahli dan trampil. Untuk membuat hasil cetakannya ketan yang telah dikukus diisikan pada cetakan dan alat pres ini bekerja ketika arduino hidup dan apabila sensor infrared bekerja mendeteksi adanya objek/ cetakan rengginang maka relay bekerja dan menggerakkan motoran maka alat pres bekerja mengepres rengginang.Pada dasarnya alat untuk pembuatan rengginang otomatis ini menggunakan arduino uno dengan motoran dc untuk menggerakkan alat pres dengan delay pada relay dan pembacaan objek menggunakan sensor infrared. Kata Kunci : Alat pres, Arduino.
ANALISIS PENGUJIAN KAPASITAS BATERAI 110 VOLT GROUP 2 (SISTEM 500 KV) GITET MANDIRANCAN Idris Afandi; Rahmat Hidayat; Insani Abdi Bangsa
Power Elektronik : Jurnal Orang Elektro Vol 10, No 2 (2021): POWER ELEKTRONIK
Publisher : Politeknik Harapan Bersama Tegal

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30591/polektro.v10i2.2559

Abstract

Abstract  Battery is a DC system device, its existence is very important in the world of electricity to maintain the stability of the DC system. Battery function in Extra High Voltage Substation (GITET) as a backup to supply DC device components such as relays, PMS (Disconnecting Switch), PMT (Voltage Breaker), and SCADATEL telecommunication devices. In the event of blackout, the rectifier does not get a power supply whose function is to convert the AC to DC power current to meet the needs of the DC device lsitrik supply remains active and working, so that the battery that replaces the role of the rectifier to maintain the stability of the DC system until the repair is complete. To maintain the stability and feasibility of battery function, routinely conducted tests on batteries carried out once every 2 years. This paper will compare the data of test results conducted in 2018 and 2020. From the results of the comparison data obtained the function of the state of the battery. Testing the battery capacity through 4 stages, floating is a battery in a full charger does not receive and emits current under normal circumstances the battery is connected to the rectifier. Equalizing aims to equalize and level the voltage value on each battery cell. Dischaerge Battery is a battery testing process to obtain a total efficiency capacity value (Ah) of the battery. When the battery is discharged large, the next step is boosting to restore the voltage value at a normal state (floating) 1.40-1.44 volts.
ANALISA PENGUJIAN KUALITAS GAS SF6 PADA PEMUTUS TENAGA (PMT) 66 KV BAY REAKTOR 4R2 DI GITET BANDUNG SELATAN Dede Siti Nurjannah; Dian Budhi Santoso; Insani Abdi Bangsa
Power Elektronik : Jurnal Orang Elektro Vol 10, No 2 (2021): POWER ELEKTRONIK
Publisher : Politeknik Harapan Bersama Tegal

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30591/polektro.v10i2.2568

Abstract

Abstract  Electrical energy is a necessity that is needed by everyone. To ensure the reliability of electrical energy, the electrical equipment used must be regularly maintained. One of the maintenance carried out is testing the SF6 gas on the power breaker (PMT). This test is carried out to determine the quality of SF6 gas which functions as an insulation medium for PMT. Because when there is a fault current or a normal current at the time the PMT is cut off, an arc will arise which can damage the PMT equipment itself. Therefore, the quality of SF6 gas in PMT must be maintained under normal conditions. In the SF6 gas test, the SF6 Multi Analyzer test tool is used which functions to ensure that the quality of the SF6 gas at PMT is still in good condition. In routine maintenance activities, SF6 gas testing is carried out at 66 kV PMT which is in the 4R2 Reactor Bay. From the test results, the gas purity value of SF6 is 99.9%, the product decomposition or SO2 content of SF6 gas is 26 ppmv, the dew point value is -21.2 ºC, and the pressure value is 0.735 MPa. Based on the test results, there is an anomaly in PMT, namely the results of the SO2 content test in SF6 gas are not normal. The SO2 value exceeds the predetermined standard limit, which exceeds the maximum limit of 12 ppmv. Therefore, in accordance with the analysis of the FMEA method, that is, if there is a bad quality test result for SF6 gas, then SF6 gas replacement and SF6 gas purity testing must be carried out so that there is no widespread disturbance and to ensure the reliability of the electric power distribution system. After replacing SF6 gas, the test results show the value of SO2 = 0 ppmv.
PERANCANGAN VIRTUAL PRIVATE NETWORK DENGAN PROTOKOL PPTP MENGGUNAKAN MIKROTIK UNTUK KEBUTUHAN REMOTE ACCESS Vicky Phang; Endah Setyaningsih
Power Elektronik : Jurnal Orang Elektro Vol 10, No 2 (2021): POWER ELEKTRONIK
Publisher : Politeknik Harapan Bersama Tegal

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30591/polektro.v10i2.2573

Abstract

Abstract  Internet has become an essential requirement for communication. By using the internet, it is possible for someone to get information anytime and anywhere. The internet is also used in local networks. The local network connects personal devices and workstations in an organization for the use of shared resources. The local network cannot be accessed from outside carelessly. A Virtual Private Network (VPN) allows devices outside the local network to connect using a public network anywhere on the condition that the device is connected to the internet. Therefore, in this journal a VPN network with a Point-to-Point Tunneling Protocol (PPTP) is designed using a MikroTik router. The PPTP protocol adds data security in these networks. A VPN network is designed to connect a total of two computers, one in the local network and one outside the local network. The VPN account that is created is for one device only. Computers on the local network use the Windows 10 operating system while computers outside the network use the Windows 7 operating system. Devices on the local network are connected using a straight type UTP cable with an RJ45 connector. The router used is the MikroTik hAP lite RB941-2nd router. The router is connected to a public network with an IP address of 103.83.174.25. The media used to configure the MikroTik router is WinBox version 3.27 (64-bit).
SISTEM PENGUKURAN SUHU TUBUH OTOMATIS BERBASIS ARDUINO SEBAGAI ALAT DETEKSI AWAL COVID-19 Iqbal Ardiyansah; Lela Nurpulaela
Power Elektronik : Jurnal Orang Elektro Vol 10, No 2 (2021): POWER ELEKTRONIK
Publisher : Politeknik Harapan Bersama Tegal

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30591/polektro.v10i2.2574

Abstract

Public places such as offices, factories or public facilities are places that have high risk of  COVID-19 transmission. Therefore, proper and fast precautions are needed, by complying with health protocols, including that every employee or person who wants to enter an office building, factory or other public facilitiesis checked for temperature by officers as early detection of COVID-19. This study discusses the design of an Arduino-based automatic body temperature measuring device which has a reminder alarm if the body temperature is above 37.30 °C. This tool is connected to a smartphone or computer device via bluetooth. This body temperature measuring device utilizes the DS18B20 sensor to measure temperature in units of Celsius (0C). The data is also displayed in the 16x2 (cm) LCD on it. The results of the test for measuring body temperature is compared to thermo gun, have a deviation range of 1,05-1,92%. It is expected that this body temperature measuring device can be installed in public places that need to carry out checks on people who want to enter the buildings or offices. Fortunetly, the operators can stand in the saving place that is far away from the virus trnsmission.

Page 1 of 18 | Total Record : 175