Article Per Year (5 Year)
p-Index From 2019 - 2024
1.456
P-Index
This Author published in this journals
All Journal Sainteks: Jurnal Sain dan Teknik Inaba of Community Services Journal
Filly Pravitasari
Universitas Insan Cendekia Mandiri
Chemical Engineering, Chemistry & Bioengineering Chemistry Computer Science & IT Decision Sciences, Operations Research & Management Economics, Econometrics & Finance Engineering Industrial & Manufacturing Engineering Languange, Linguistic, Communication & Media Public Health Social Sciences

Published : 5 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 4 Documents
Search
Journal : Sainteks: Jurnal Sain dan Teknik

 1 
Pengaruh Jumlah Putus Benang Terhadap Quality Control Jahitan di CV Batara Apparel Afriani Kusumadewi; Filly Pravitasari
Sainteks: Jurnal Sain dan Teknik Vol 3 No 1 (2021): Maret
Publisher : Universitas Insan Cendekia Mandiri

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.37577/sainteks.v3i1.295

Abstract

One of the problems that related to quality and often occurs in the sewing process at CV Batara Apparel is that there are frequent thread break problems. Termination problems that occur are caused by an error during the thread installation process that does not pass through the needle bar hole and the thread is directly passed through the needle. This results in defects in stitches such as broken stitches. In order to solve the thread break problem caused by an error during the thread installation process that does not pass through the needle bar hole, it can be overcome by implementing SOP (Standard Operational Procedure) on proper and correct machine usage procedures, briefing supervisors with the production manager so that the problems occurs when production takes place can be handled properly. In addition, the implementation of regular maintenance schedules can also solve the thread break problems that occur. Keywords: thread break, loose stitches, quality control, SOP
Pengaruh Penyetelan Squeezing Roll Pada Mesin Sizing Terhadap Kekuatan Benang Filly Pravitasari; Afriani Kusumadewi
Sainteks: Jurnal Sain dan Teknik Vol 3 No 1 (2021): Maret
Publisher : Universitas Insan Cendekia Mandiri

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.37577/sainteks.v3i1.296

Abstract

The process of applying starch to the warp yarn in order to increase the weaving power of the warp yarn in the presence of a starch layer, is expected to increase the strength of the yarn and reduce the yarn hairs. One of the factors that influence the sizing process is the amount of pressure in the squeezing roll. In this process, the sizing machine uses a double size box and each size box has 2 (two) squeezing rolls. The material used is Combed Ne 40 yarn with construction ,which is the amount of tetal or the density of the yarn with the construction included in the tetal of the dense warp yarn. The method used by comparing the pressure of squeezing roll process 1 and process 2. In the first process, the squeezing roll 1 is set at 3 kN and squeezing roll 2 is 3.5 kN, while in the second sizing process, the squeezing roll 1 is set at 4 kN and squeezing roll 2 for 5kN. After the experimental process was carried out, the starch warp yarn strength was obtained which was higher, namely 351.93gr and compared to process 2 which was 345.84 gr. The higher from the strength of the starchy yarn, can make it better for weaving process.
Pengaruh Variasi Timing Opening Angle Terhadap Jumlah Weft Stop pada Pertenunan Kain dengan Anyaman Keper 2/1 1 di Mesin Air Jet Loom Filly Pravitasari; Afriani Kusumadewi
Sainteks: Jurnal Sain dan Teknik Vol 3 No 2 (2021): September
Publisher : Universitas Insan Cendekia Mandiri

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.37577/sainteks.v3i2.334

Abstract

In the weaving process, the process of launching the weft yarn is an important thing to consider. One of the obstacles that often occurs in the process of launching feed using a water jet loom machine is the amount of feed stuck (weft stop). The cause of the weft stop is because the process of opening the warp mouth is not clean and the weft thread slides inappropriately or too fast so that the warp mouth is in a small condition. Variations in timing opening angle of 700, 800 and 900 determine the size of the warp mouth opening, the time the weft will slide and the time the weft will arrive. From the three variations of the timing opening angle, the number of weft stops at the timing opening angle of 800 is smaller than the timing opening angle of 700 and 900, which is namely the number of big loops 0.6 times and end loops 0.8 times per hour.
Determination of Production Targets on Sewing for the Front Body of H&M Pajamas Jogger Pants Afriani Kusumadewi; Filly Pravitasari; Feny Nurherawati
Sainteks: Jurnal Sain dan Teknik Vol 4 No 2 (2022): September
Publisher : Universitas Insan Cendekia Mandiri

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.37577/sainteks.v4i2.458

Abstract

The process of sewing the front body of an order for H&M Pajamas Jogger Pants has a fairly high quality, but the target for setting production targets is based on experience and estimates only. The setting of a fairly high production target of 640 pcs/day is often not achieved because the determination of the production target is not based on the level of difficulty of the work carried out by the operator (easy, medium, or difficult), the operator's skill as well as the condition of the machine used in the process. condition is good or not, so that the target set is often not achieved because it is not in accordance with the condition of the operator's ability in general. Based on the observation of the operator's working time measurement, the total standard time for the 26 manufacturing processes for the front body component of the order of H&M Pajamas Jogger Pants was 23,029 minutes. After getting the total standard time for making the front body component of the order for these H&M Pajamas Jogger Pants, a new production target can be determined, which is 542 pcs/day. This new production target is made to represent the general working conditions of operators and has taken into account the factors of slack, work fatigue and other unavoidable obstacles.
Co-Authors Afriani Kusumadewi Afriani Kusumadewi Feny Nurherawati Feny Nurherawati Luciana Luciana Riza Rizkiah