Garuda - Garba Rujukan Digital

Pengaruh Jenis dan Volumetrik Fiber terhadap Kekuatan Transversal Reparasi Plat Resin Akrilik Pramudya Aditama; Siti Sunarintyas; Widjijono Widjijono
Majalah Kedokteran Gigi Indonesia Vol 1, No 1 (2015): August
Publisher : Faculty of Dentistry, Universitas Gadjah Mada

Resin akrilik merupakan bahan yang sering digunakan dalam pembuatan basis gigi tiruan. Kelemahan resin akrilik adalah mudah patah. Salah satu cara untuk mengatasi masalah tersebut adalah dengan menambahkan polyethylene (PE) atau glass fiber. Tujuan dari penelitian ini untuk mengetahui pengaruh jenis dan volumetrik fiber terhadap kekuatan transversal reparasi plat resin akrilik. Penelitian ini menggunakan dua puluh lima plat resin akrilik kuring panas berukuran 65 x 10 x 2,5 mm. Subjek dipreparasi untuk membuat jarak 3 mm dan sudut bevel 45o. Subjek dibagi menjadi 5 kelompok, masingmasing kelompok terdiri dari 5 subjek. Kelompok 1 (kontrol) tanpa penambahan fiber, kelompok II dengan penambahan 3,7% v/v PE fiber, kelompok III dengan penambahan 7,4% v/v PE fiber, kelompok IV dengan penambahan 3,7% v/v E-glass fiber, dan kelompok V dengan penambahan 7,4% v/v E-glass fiber. Seluruh plat direndam dalam air destilasi selama satu hari pada suhu 37oC. Pengujian kekuatan transversal plat resin akrilik dengan menggunakan Universal Testing Machine dan data yang didapat dianalisis menggunakan ANAVA dua jalur dengan tingkat kepercayaan 95%. Rerata kekuatan transversal (MPa) reparasi plat resin akrilik yang diperkuat fiber: 3,7% v/v PE fiber (67,77±3,34); 7,4% v/v PE fiber (80,37±8,42); 3,7% v/v E-glass fiber (96,72±5,43); 7,4% v/v E-glass fiber (109,44±4,98); sedangkan reparasi plat resin yang tidak diperkuat fiber menghasilkan kekuatan transversal 56,27±4,7 MPa. Hasil analisis menggunakanANAVA dua jalur menunjukkan variabel jenis dan volumetrik fiber memberikan pengaruh signifikan (p<0,05), sedangkan interaksi antara jenis dan volumetrik fiber tidak berpengaruh signifikan (p>0,05). Uji post hoc Tukey menunjukkan perbedaan signifikan (p<0,05) untuk seluruh kelompok perlakuan. Penambahan E-glass fiber dalam reparasi plat resinakrilik mampu meningkatkan kekuatan transversal lebih tinggi dibandingkan dengan menggunakan PE fiber. Peningkatan volumetrik fiber dapat meningkatkan kekuatan transversal reparasi plat resin akrilik. Effect Of Type And Volumetric Fiber On Transverse Strength Of Acrylic Resin Plate Repair. Acrylic resin is the most common denture base material. A disadvantage of acrylic resin is that it is easily fractured. One way to resolve this problem is by adding polyethylene (PE) or glass fibers. The purpose of this research is to find out about the effect of type and volumetric fiber on transverse strength of acrylic resin plate repaired. The experiment involved twenty five plates of heat cured acrylic with the dimensions of 65 x 10 x 2.5 mm. The speciments were prepared to create a 3 mm gap and 45° bevel. The subjects were divided into 5 groups; each group consisted of 5. Group I (control) was without fiber reinforcement, group II reinforced with 3.7% v/v PE fiber, group III reinforced with 7.4% v/v PE fiber, group IV reinforced with 3.7% v/v E-glass fiber, and group V reinforced with 7.4% v/v E-glass fiber. All plates were soaked in distilled water for one day at 37° C temperature. The plates were tested for transverse strength with Universal Testing Machine and all data obtained were analyzed with two way ANOVA at 95% confidence level. The mean of transverse strength (MPa) of the acrylic resin plate repair reinforced with fiber: 3.7% v/v PE fiber was (67.77±3.34); 7.4% v/v PE fiber (80.37±8.42); 3.7% v/v E-glass fiber (96.72±5.43); 7.4% v/v E-glass fiber (109.44±4.98); while the transverse strength of the acrylic resin plate with no fiber reinforced was 56.27±4.7 MPa. Two way ANOVA analysis shows that type and volumetric fiber had significant effect (p<0.05), while the interaction between type and volumetric fiber had no significant effect (p>0.05). Tukey post hoc test shows significant difference (p<0.05) for all groups. The addition of E-glass fibers in the acrylic resin plate repaired increased the transverse strength higher than that with PE fibers. The increase in volumetric fibers might improve the transverse strength of the acrylic resin plate repaired.

Pengaruh volumetrik e-glass fiber terhadap kekuatan transversal reparasi plat gigi tiruan resin akrilik Pramudya Aditama; Erwan Sugiatno; Muhamad Rifqi Tri Nuryanto
Majalah Kedokteran Gigi Indonesia Vol 2, No 1 (2016): April
Publisher : Faculty of Dentistry, Universitas Gadjah Mada

The effect of e-glass fiber volumetric on transverse strength of an acrylic resin denture plate repair. Acrylic resin is the most commonly material for the denture base. A disadvantage of acrylic resin is that it is easily to be cracked. One of the ways to resolve this problem is by adding the E-glass fibers. The purpose of this research was to find out the effect of volumetric E-glass fiber on transverse strength of an acrylic resin denture plate repair. The experiment involved thirty plates of heat cured acrylic with the dimensions of 65 × 10 × 2.5 mm. The specimens were prepared to create a 3-mm gap and 45° bevel. Subjects were divided in to 3 groups, each of which contained 10. Group I (control) was with no fiber reinforcement, group II was reinforced with 3.7vol % E-glass fiber, and group III was reinforced with 7.4 volume % E-glass fiber. All plates were soaked in distillation water for one day at 37 °C. Plates were tested for transverse strength with Universal Testing Machine and all data obtained was analyzed with one way anova at 95% confidence level (α= 0.05). The significant difference was found between the transversal force of acrylic resin plat enforced with fiber and other group without being reinforced with fibers (p<0.05). Group reinforced with 7.4 vol % E-glass fibers showed a significant difference (higher) than the group reinforced with 3.7 volume % fibers. The addition of E-glass fibers in an acrylic resin plate repair material increased the transverse strength. The increase in volumetric fibers might improve the transverse strength of an acrylic resin plate repair material.ABSTRAKResin akrilik merupakan bahan yang sering digunakan dalam pembuatan basis gigi tiruan. Kekurangan dari bahan resin akrilik adalah mudah patah. Salah satu cara yang dapat digunakan untuk mengatasi masalah tersebut adalah dengan menambahkan E-glass fiber. Tujuan untuk mengetahui pengaruh volumetrik E-glass fiber terhadap kekuatan transversal reparasi plat gigi tiruan resin akrilik. Penelitian ini menggunakan tiga puluh plat resin akrilik kuring panas dengan ukuran 65 × 10 × 2,5 mm. Spesimen dipreparasi untuk membentuk jarak 3 mm dan sudut bevel 45°. Subjek kemudian dibagi menjadi 3 kelompok, setiap kelompok terdiri dari 10 plat. Kelompok I (kontrol) tanpa diberikan penguat fiber, kelompok II diperkuat dengan 3,7 vol % E-glass  ber, dan kelompok III diperkuat dengan 7,4 vol % E-glass fiber. Seluruh plat kemudian direndam dalam air destilasi selama satu hari pada suhu 37 °C. Plat resin akrilik kemudian diuji menggunakan Universal Testing Machine untuk mengetahui kekuatan transversal dan data yang didapatkan dianalisis menggunakan Anova satu jalur dengan tingkat kepercayaan 95% (α=0,05). Hasil menunjukkan terdapat perbedaan signifikan antara kekuatan transversal plat resin akrilik yang diperkuat dengan fiber dengan kelompok tanpa diperkuat fiber (p < 0,05). Kelompok yang diperkuat dengan 7,4 vol % E-glass fiber menunjukkan perbedaan signi kan (lebih tinggi) dibandingkan kelompok yang diperkuat dengan 3,7 vol % fiber. Kesimpulan bahwa peningkatan volume dari E-glass fiber dapat meningkatkan kekuatan transversal reparasi plat gigi tiruan resin akrilik.

The transversal strength comparison between polyethylene and glass fiber as an acrylic resin denture plate repair material Pramudya Aditama; Erwan Sugiatno; Sabdayana Sabdayana
Majalah Kedokteran Gigi Indonesia Vol 5, No 1 (2019): April
Publisher : Faculty of Dentistry, Universitas Gadjah Mada

Acrylic resin is the most commonly used denture base material. However, it has a shortage of being easily broken. One way to resolve this problem is by adding polyethylene (PE) or glass fibers. The purpose of this research is to compare the transversal strength of PE and glass fibers from denture plate acrylic resin repair material. The experiment involved 32 plates of heat cure acrylic with the dimensions of 65 mm x 10 mm x 2.5 mm. The speciments were prepared to create a 3 mm gap and 45° bevel. Subjects were divided into 2 groups, each group containing 16 plates. Group I was reinforced with PE fiber and Group II was reinforced with glass fiber. All plates were soaked in distillation water for one day at 37 °C. Plates were tested for transverse strength with universal testing machine and all data were analyzed with independent t-tes at 95% confidence level. Macro photo analysis was used to observed the bond failure on fiber and resin. The mean of transverse strength (MPa) denture plate acrylic resin repair material reinforced with PE fiber was (67.38 ± 4.31) MPa, while glass fiber was (93.61 ± 6.14) MPa. Independent t-tes showed that type of fiber had a significant effect (p<0.05). Thus, it is possible to conclude that addition of glass fibers in denture plate acrylic resin repair material increased the transverse strength and made it stronger than those added with PE fibers.

The effect of fiber type and position on the transverse strength of an fiber reinforced composite (FRC) bridge Pramudya Aditama; Erwan Sugiatno; Murti Indrastuti
Majalah Kedokteran Gigi Indonesia Vol 6, No 3 (2020): December
Publisher : Faculty of Dentistry, Universitas Gadjah Mada

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.22146/majkedgiind.44616

Fixed bridge made of porcelain fused to metal (PFM) is one of the widely used dentures. However, this type of denture is easily broken and cracked. As an alternative, a fixed bridge made of fiber-reinforced composite (FRC) is produced with more benefits since it is more efficient in terms of time and cost. The purpose of this research is to find out the effect of type and fiber position on the transverse strength of an FRC bridge. The experimentinvolved 35 rod of FRC with the dimensions of 25x2x2 mm3. Subjects were divided into seven groups, each of which containing five subjects. Group I, II, III was reinforced with glass fiber on compression side, neutral side, and tension side. Group IV, V, VI were reinforced with polyethylene (PE) fiber on compression side, neutral side, and tension side. Group VII was not reinforced with any fiber. Rods were tested for transverse strength with universaltesting machine and all data were analyzed with two way ANOVA at 95% confidence level. The results showed that type and position of fiber had a significant effect (p<0.05), while the interaction between type and position of fiber had no significant effect (p>0.05). Least significance different post hoc test showed significant difference (p<0.05) for all groups, except between compression and no fiber. The conclusion of this research was that addition of glass fibers on tension side in bridge FRC increased the transverse strength to be higher than that with PE fibers. Fiber placement on tension side might improve the transverse strength than that of the other side.

EFFECT OF SILICA COATING IN ACRYLIC ARTIFICIAL TEETH ON SURFACE ROUGHNESS, CONTACT ANGLE, AND GROWTH OF STREPTOCOCCUS MUTANS Adella Syvia Maharani; Pramudya Aditama; Murti Indrastuti; Suparyono Saleh
ODONTO : Dental Journal Vol 8, No 2 (2021): December 2021
Publisher : Faculty of Dentistry, Universitas Islam Sultan Agung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30659/odj.8.2.106-112

ABSTRACTBackground: Acrylic resin artificial teeth is easily to have bacterial adhesion. It is necessary to perform a treatment on that surface, in order to reduce bacterial adhesion. This study aimed to reveal the effect of silica coating in acrylic resin artificial teeth on surface roughness, contact angle measurement, and the growth of Streptococcus mutans.Method: The study was conducted on two groups (n=16) of disk-shaped acrylic resin artificial teeth with a diameter of 10 mm and thickness of 2 mm. A 2% silica coating material was obtained by diluting 2 g silica nanoparticles on 100 ml of ethanol. Surface roughness, contact angle measurement, and the growth of Streptococcus mutans was measured using surface roughness measuring instrument, camera digital, and colony counter. The data obtained were then analyzed using T-test (p<0.05).Result: The results showed that the surface roughness and contact angle measurement in group I (0.29±0.08 μm); (79,49º ± 10,88º) was higher than group II (0.17±0.05 μm); (34,77º±0,05º). The growth of Streptococcus mutans in group I was also higher (32.28±3.75 CFU/ml) than group II (24.83±3.47 CFU/ml). Conclusion: The study concluded that there is an effect of silica coating on surface roughness, contact angle measurement, and the growth of Streptococcus mutans in acrylic resin artificial teeth.

Pemberdayaan Masyarakat Desa Panjangrejo Bantul Yogyakarta sebagai Upaya Mewujudkan Desa Sehat Gigi dan Mulut 2030 Pramudya Aditama; Leny Pratiwi Ariesandy; Fimma Naritasari; Nunuk Purwanti
Jurnal Pengabdian kepada Masyarakat (Indonesian Journal of Community Engagement) Vol 3, No 2 (2018): Maret
Publisher : Direktorat Pengabdian kepada Masyarakat Universitas Gadjah Mada

Oral health problem in Indonesian has increased. Yogyakarta is the fourth province with the highest number oral health problem and the third province with the highest Effective Medical Demands (EMD) for oral health in Indonesia. This fact indicates that it needs the attention of many parties to solve this problem, especially in Yogyakarta. Through community empowerment, community will be able to independently maintain their oral health and can be expected to be one of a solution to overcome the existing problems.The establishment of Oral Health Cadre (KADEGI) is a form of community empowerment strategy in terms of human resource development. Community empowerment, using the Participatory Learning and Action (PLA) method, is very effective to help the KADEGI mastered several skills such as (a) able to do dental health education, (b) able to do early detection of oral disease and (c) able to refer oral health cases to the nearest public health services (puskesmas).The results of KADEGI's work in data collecting of oral health problem in Desa Panjangrejo showed that from 1.198 respondents who were examined, 64% of respondents had tooth cavities and 49% had debris and calculus. These data indicate that Desa Panjangrejo’s resident are still need special attention in oral health problem by various parties.

Protesa obturator definitif resin akrilik pada pasien systemic lupus erythematosus (SLE) pasca maksilektomiAcrylic resin definitive obturator prosthesis in systemic lupus erythematosus (SLE) patients post-maxillectomy Pramudya Aditama; Erwan Sugiatno; Murti Indrastuti; Endang Wahyuningtyas
Jurnal Kedokteran Gigi Universitas Padjadjaran Vol 32, No 2 (2020): November 2020 (Suplemen 1)
Publisher : Fakultas Kedokteran Gigi Universitas Padjadjaran

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24198/jkg.v32i2.28175

ABSTRAKPendahuluan: Systemic lupus erythematosus (SLE) merupakan inflamasi kronis yang dapat melibatkan sistem saraf, membran mukosa, dan organ lain dalam tubuh. Avascular bone necrosis (AVN) merupakan gejala yang muncul pada penderita SLE. Maksilektomi dilakukan pada tulang maksila yang mengalami AVN. Penutupan celah pasca maksilektomi tersebut dilakukan dengan cara menggunakan protesa maksilofasial intraoral yaitu obturator. Tujuan laporan kasus ini mengkaji rehabilitasi prostetik menggunakan protesa obturator definitif resin akrilik pada penderita SLE pasca maksilektomi. Laporan kasus: Seorang wanita berusia 21 tahun datang ke Poli Gigi dan Mulut RSUP Dr. Sardjito dengan keluhan bau mulut, hilangnya gusi pada langit-langit, dan kegoyahan gigi rahang atas. Pasien didiagnosis SLE sejak lebih dari 1 tahun yang lalu. Pada pemeriksaan intraoral, selain lesi pada mukosa palatum, ditemukan juga nekrosis pada tulang palatum, kehilangan gigi 14, 15, 16, dan 25, serta kegoyahan derajat 3 pada seluruh gigi rahang atas yang tersisa. Pasien dirawat dengan obat Myfortic (2 x 180 mg/hari) dan Fluconazole (1x150 mg/hari) kemudian dirujuk ke Poli Bedah Mulut untuk dilakukan maksilektomi, dilanjutkan dengan pembuatan protesa obturator oleh tim prostodonti. Pasien dibuatkan obturator pasca bedah untuk menutup celah palatum pasca maksilektomi. Pencetakan menggunakan bahan hydrocolloid irreversible sebelum operasi untuk pembuatan obturator pasca bedah. Insersi obturator menunjukkan celah palatum tertutup rapat oleh plat akrilik. Retensi didapatkan menggunakan kawat stainless pada titanium wire mesh pengganti tulang maksila. Tidak ada keluhan saat kontrol, penelanan baik. Tiga bulan pasca pemakaian obturator pasca bedah dilakukan pemasangan obturator definitif resin akrilik rahang atas. Pemeriksaan klinis menunjukkan suara sengau berkurang, estetis, dan pengunyahan baik. Simpulan: Protesa obturator definitif resin akrilik pada pasien SLE pasca maksilektomi dapat mengembalikan fungsi estetik, mengurangi suara sengau (mengembalikan fungsi bicara), mengembalikan fungsi penelanan, dan pengunyahan.Kata kunci: Maksilektomi, obturator definitif resin akrilik, systemic lupus erythematosus. ABSTRACTIntroduction: Systemic lupus erythematosus (SLE) is a chronic inflammation that involves the nervous system, mucous membranes, and other organs. Avascular bone necrosis (AVN) is a symptom that appears in people with SLE. Maxillectomy is performed on the maxillary bone affected with AVN. The post-maxillectomy gap closure was performed using an intraoral maxillofacial prosthesis, namely an obturator. This case report was aimed to examine the prosthetic rehabilitation using Acrylic resin definitive obturator prosthesis in SLE patients post-maxillectomy. Case report: A 21-years-old woman came to Dr Sardjito Oral Clinic with complaints of bad breath, palatogingival loss, and loose maxillary teeth. The patients was diagnosed with SLE for more than one year prior. The intraoral examination result showed that apart from the palatal mucosa lesions, there was also found necrosis of the palate bone, loss of teeth 14, 15, 16, and 25, and grade 3 loose of all of the remaining maxillary teeth. The patient was treated with Myfortic® (2 x 180 mg/day) and Fluconazole® (1 x 150 mg/day), then referred to the Oral Surgery Clinic for maxillectomy, followed the fabrication of obturator prostheses by the prosthodontist team. The patient was assigned a postoperative obturator to close the palate gap after maxillectomy. An imprint was carried out using an irreversible hydrocolloid material before surgery for the manufacture of a post-surgical obturator. The obturator insertion shows that the palate gap was tightly closed by an acrylic plate. Retention was obtained using the stainless wire on titanium wire mesh instead of the maxillary bone—the patients presented no complaints during control and had adequate ingestion. Three months after wearing a postoperative obturator, the acrylic resin definitive obturator prosthesis was then installed. Clinical examination showed reduced nasal sound, and better aesthetical and mastication aspect. Conclusion: Acrylic resin definitive obturator prosthesis in post-maxillectomy SLE patients can restore aesthetic function, reduce nasal sound (restore speech function), restore swallowing and mastication function.Keywords: Maxillectomy, acrylic resin definitive obturator prosthesis, systemic lupus erythematosus.

EFFECT OF SILICA COATING IN ACRYLIC ARTIFICIAL TEETH ON SURFACE ROUGHNESS, CONTACT ANGLE, AND GROWTH OF STREPTOCOCCUS MUTANS Adella Syvia Maharani; Pramudya Aditama; Murti Indrastuti; Suparyono Saleh
Odonto : Dental Journal Vol 8, No 2 (2021): December 2021
Publisher : Faculty of Dentistry, Universitas Islam Sultan Agung

ABSTRACTBackground: Acrylic resin artificial teeth is easily to have bacterial adhesion. It is necessary to perform a treatment on that surface, in order to reduce bacterial adhesion. This study aimed to reveal the effect of silica coating in acrylic resin artificial teeth on surface roughness, contact angle measurement, and the growth of Streptococcus mutans.Method: The study was conducted on two groups (n=16) of disk-shaped acrylic resin artificial teeth with a diameter of 10 mm and thickness of 2 mm. A 2% silica coating material was obtained by diluting 2 g silica nanoparticles on 100 ml of ethanol. Surface roughness, contact angle measurement, and the growth of Streptococcus mutans was measured using surface roughness measuring instrument, camera digital, and colony counter. The data obtained were then analyzed using T-test (p<0.05).Result: The results showed that the surface roughness and contact angle measurement in group I (0.29±0.08 μm); (79,49º ± 10,88º) was higher than group II (0.17±0.05 μm); (34,77º±0,05º). The growth of Streptococcus mutans in group I was also higher (32.28±3.75 CFU/ml) than group II (24.83±3.47 CFU/ml). Conclusion: The study concluded that there is an effect of silica coating on surface roughness, contact angle measurement, and the growth of Streptococcus mutans in acrylic resin artificial teeth.

Title

Found 8 Documents
Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title Search

Found 8 Documents Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title

Found 8 Documents
Search