Article Per Year (5 Year)
p-Index From 2019 - 2024
1.456
P-Index
This Author published in this journals
All Journal Sinergi JATI UNIK : Jurnal Ilmiah Teknik dan Manajemen Industri Jurnal INTECH Teknik Industri Universitas Serang Raya Jurnal Media Teknik dan Sistem Industri
Muhamad Bob Anthony
Universitas Serang Raya
Civil Engineering, Building, Construction & Architecture Control & Systems Engineering Decision Sciences, Operations Research & Management Electrical & Electronics Engineering Engineering Industrial & Manufacturing Engineering Mechanical Engineering Transportation

Published : 13 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 13 Documents
Search

 1   2 
Persepsi antara Risiko Keselamatan Berkendaraan dengan Perilaku Pemakaian Safety Belt pada Driver Truk Muhamad Bob Anthony
Jurnal INTECH Teknik Industri Universitas Serang Raya Vol. 4 No. 2 (2018)
Publisher : Universitas Serang Raya

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (379.156 KB) | DOI: 10.30656/intech.v4i2.927

Abstract

Deaths and injuries from traffic accidents have become health problems for people throughout the world including Indonesia. The saddest data from the victims who died due to traffic accidents found that 10,428 people were killed in 2017 because the drivers did not use seat belts. This research aims to see the relationship between the perception of safety risk i.e. the ability, knowledge and environmental factors with the behavior of the use of safety belts in truck drivers in mining companies. This research is a comparative causal research i.e. research that states the relationship of one variable causes other variables. What is affected is the dependent variable, namely the use of safety belt behavior and the influencing variable is the independent variable, namely the perception of the risk of driving safety. Participants are 25 mining company truck drivers. The data obtained is then processed and analyzed using the SPSS version 16. Based on the results of data processing and analysis, it is found that the ability, knowledge and work environment factors have an influence on the safety belt usage behavior.
Analisis Risiko Kerja pada Area Hot Metal Treatment Plant Divisi Blast Furnace dengan Metode Hazard Identification and Risk Assessment (HIRA) Muhamad Bob Anthony
Jurnal INTECH Teknik Industri Universitas Serang Raya Vol. 5 No. 1 (2019)
Publisher : Universitas Serang Raya

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (395.286 KB) | DOI: 10.30656/intech.v5i1.1461

Abstract

This study aims to determine the value of the risk of work hazard potential and the level of risk of potential occupational hazards in the blast furnace division of hot metal treatment plant which is currently in the commissioning stage. This study uses an approach with the HIRA (Hazard Identification and Risk Assessment) method to determine the value of the risk of potential occupational hazards and the level of risk of potential occupational hazards. The results obtained by using HIRA (Hazard Identification and Risk Assessment) obtained 26 risks classified by potential hazards, namely nine risks included in the high category (H), seven risks moderate category (M) and the remaining ten risks involved in the low category ( L). The recommendation that can give is to carry out detailed mitigation of the risk of high (H) and moderate (M) categories until the risk level falls to the risk of the low (L) category before the blast furnace plant is fully operating.
Usulan Perbaikan Mixing Design Produk Sinter Ore dengan Menggunakan Metode Simpleks Sahrupi Sahrupi; Muhamad Abdul Kirom Maulana; Muhamad Bob Anthony
Jurnal INTECH Teknik Industri Universitas Serang Raya Vol. 6 No. 2 (2020)
Publisher : Universitas Serang Raya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30656/intech.v6i2.2503

Abstract

Sinter ore merupakan produk setengah jadi dalam pembuatan baja. Produk ini dihasilkan dari perpaduan (mixing) raw material dibagian sinter plant untuk mendapatkan karakteristik produk baja yang berkualitas. Berdasarkan hasil identifikasi masalah di bagian Sinter Plant, ditemukan bahwa proses produksi produk sinter ore masih belum efisien. Hal ini dibuktikan dari komposisi material hasil mixing design produk cenderung melebihi target properties proses mixing design yang diinginkan oleh perusahaan. Penelitian ini bertujuan untuk mencari nilai efisiensi biaya produksi produk sinter ore dan dapat mencapai target properties produk sinter ore yang ditetapkan oleh perusahaan. Penelitian dilakukan dengan menggunakan data karakteristik produk yang menjadi target properties dalam mixing design produk sinter ore tahun 2019. Perhitungan mixing design dengan menggunakan metode simpleks. Pengolahan data dengan menggunakan metode simpleks dilakukan dengan cara eliminasi secara iteratif sebanyak 5 kali perhitungan sampai diperoleh solusi optimal. Penerapan metode simpleks dalam pengolahan mixing design produk sinter ore menghasilkan nilai efisiensi yang cukup signifikan bagi perusahaan. Nilai efisiensi yang dapat dicapai sebesar 1.050.210 USD berdasarkan penurunan biaya mixing design dari semula sebesar 20.445.600 USD menjadi sebesar 19.395.390 USD. Pencapaian target properties komposisi material hampir mendekati target yaitu fines ore A sebesar 0,8997, fines ore B sebesar 0, fines ore C sebesar 0,0027, concentrate sebesar 0,0201, dan sub material sebesar 0,1627. Hasil penelitian menunjukan bahwa penerapan metode simpleks dapat menghasilkan solusi optimal bagi perusahaan, baik menyangkut pencapaian keuntungan maupun efisiensi biaya.
Co-Authors Muhamad Abdul Kirom Maulana Prawoto Prawoto Sahrupi, Sahrupi