Article Per Year (5 Year)
p-Index From 2019 - 2024
0
P-Index
This Author published in this journals
All Journal Jurnal Ilmiah Teknik Mesin Poros
Abrar Riza
Unknown Affiliation
Mechanical Engineering

Published : 4 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 4 Documents
Search

 1 
ANALISIS KOMPOSISI GAS BUANG AKIBAT PERUBAHAN MAIN JET NOZZLE PADA SISTEM KARBURATOR MESIN Bernadi Ksatria Putra; Abrar Riza; Asrul Aziz
Jurnal Ilmiah Teknik Mesin POROS Vol 13, No 2 (2015): Jurnal Ilmiah Teknik Mesin POROS
Publisher : Program Studi Teknik Mesin Universitas Tarumanagara

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (739.263 KB) | DOI: 10.24912/poros.v13i2.820

Abstract

Abstract: Fuel entering through the main jet nozzle, affects engine performance and the composition of the exhaust gas is produced. Research the composition of the exhaust gases in machines otto one cylinder done with experimental method. The purpose of this study was to obtain the characteristics of the engine with exhaust gas analysis method. This research done with varying size main jet nozzle and varying the engine rotation every 400 rpm. Data processing the results of testing includes a comparison of the composition of the exhaust gases is HC, CO2, CO, O2, AFR, and the temperature of the exhaust gases. Then calculate the enthalpy of combustion for each main jet nozzle. The composition of the exhaust gases are best obtained from the main jet nozzle GX 160 which has the highest CO2 value of 20%, with the lowest CO value of 1.26% and the largest combustion enthalpy value with the value of 264.769 kJ. From the analysis can be known that the burning of the main jet nozzle GX 160 approaching the stoichiometric combustion. 
KARAKTERISTIK SIFAT MEKANIK DAN STRUKTUR MIKRO PADA MATERIAL Sn-0,7Cu-“X”Zn Ridwan Adidarma; Erwin Siahaan; Abrar Riza
Jurnal Ilmiah Teknik Mesin POROS Vol 14, No 1 (2016): Jurnal Ilmiah Teknik Mesin POROS
Publisher : Program Studi Teknik Mesin Universitas Tarumanagara

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (790.232 KB) | DOI: 10.24912/poros.v14i1.828

Abstract

Abstract: Lead (Pb) in solder has been used for decades in industries of electronic equipment. Mostly in the lead solder old electronic equipment containing 63% (Sn), 37% lead (Pb). Heating solder in high temperature steam generating heat which can damage the respiratory system. The purpose of this analytic is to obtain the characteristics of the mechanical properties of the alloy Sn-0,7Cu- "X" Zn better than the Sn-Pb alloy as an alternative to non-lead solder alloy material. Tests conducted in the form of density, melting temperature, metallography, shear strength, and hardness. The effect of addition of Zn alloy Sn-Cu-Zn increase hardness value of each acquired 85% of the material Sn-0,7Cu-10Zn, 81% were obtained from material Sn-0,7Cu-11Zn and 70% was obtained from material Sn -0,7Cu-11Zn. While the effect of adding Zn alloy Sn-Cu-Zn can increase the shear strength of each of about 29.4% on a material- 0,7Cu-10Zn Sn, 65% in material Sn-0,7Cu-11Zn and about 140% is obtained from material Sn-0,7Cu- 12Zn. 
ANALISIS PERBANDINGAN UNJUK KERJA PEMANAS AIR TENAGA SURYA TIPE PLAT DATAR DENGAN SISTEM SINGLE DAN DOUBLE CUTOFF Ivan Budiman; I Made Kartika; Abrar Riza
Jurnal Ilmiah Teknik Mesin POROS Vol 14, No 1 (2016): Jurnal Ilmiah Teknik Mesin POROS
Publisher : Program Studi Teknik Mesin Universitas Tarumanagara

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (346.952 KB) | DOI: 10.24912/poros.v14i1.829

Abstract

Abstract: Warm water is needed by human being to take a bath, wash their clothes, their dishes etc. By the photothermal conversion, the solar energy can be used to heat the water. Flat solar collector is a tool which is used to capture energy of the sun radiation then convert it into heat to heat up water in collector’s pipes. The number of glass cover used effects the performance and efficiency of the collector. From this research, it is found that the efficiency of the collector is better when the cover used are two glasses than one glasses. The temperature difference of incoming and outgoing water in the collector using two glasses 15 ̊C higher than that of one glass. 
PENGARUH VARIASI MAIN JET NOZZEL PADA SISTEM KARBURATOR TERHADAP UNJUK KERJA MESIN Alvinsen Alfonso; Abrar Riza; I Made Kartika
Jurnal Ilmiah Teknik Mesin POROS Vol 13, No 2 (2015): Jurnal Ilmiah Teknik Mesin POROS
Publisher : Program Studi Teknik Mesin Universitas Tarumanagara

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (862.474 KB) | DOI: 10.24912/poros.v13i2.819

Abstract

Abstract: This study discusses the effect of variations in the diameter of the main jet nozzles on the performance of the motor fuel. Performance analysis covering torque, power and specific fuel consumption (sfc). With the aim to determine the maximum performance that can be generated on any variation of the diameter of the main jet nozzles. At the time of this experiment performed with the engine 4 stroke Honda GX-160, using hydro tool dynamometer and using premium fuel. The data taken is the engine rotation, the force measured on the dynamometer and the time spent fuels. Tests conducted at the Laboratory of Energy Conversion Mechanical Engineering UNTAR Jakarta. Testing is done by providing the machine with a load variation of rotation remains in order to obtain a force on each spin machine with a main jet nozzle diameter variations. Variations rev the engine starts at the minimum rotation until maksimuml with fixed load, variations in the diameter of the main jet nozzles on testing. 
Co-Authors Alvinsen Alfonso Asrul Aziz Bernadi Ksatria Putra Erwin Siahaan I Made Kartika Ivan Budiman Ridwan Adidarma