Article Per Year (5 Year)
p-Index From 2019 - 2024
0.562
P-Index
This Author published in this journals
All Journal Jurnal Teknik Kimia USU FLUIDA
Yanis Fitrianti
Politeknik Negeri Bandung
Chemical Engineering, Chemistry & Bioengineering Chemistry Energy Engineering Environmental Science Materials Science & Nanotechnology

Published : 2 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 2 Documents
Search

 1 
Effect of Piping Configuration on Determining Alarm Response Time in HP Scrubber Using Dynamic Simulation In Jumanda Kasdadi; Fahmi Nur Listiani; Gianistri Maulani; Yanis Fitrianti
Fluida Vol 16 No 1 (2023): FLUIDA
Publisher : Jurusan Teknik Kimia, Politeknik Negeri Bandung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35313/fluida.v16i1.4703

Abstract

The HP scrubber is an equipment used to separate liquid from gas in the oil and gas industry. The low liquid level in the vessel is one of the abnormal conditions in the HP scrubber, a blowby gas event will happen because of a low level. So, the controller level indicator is required to prevent system damage and workplace accidents. The alarm response time is calculated in order to avoid an accident. To determine the alarm response time for a HP scrubber, a dynamic process simulation method can be used using Aspen HYSYS version 12. In a process simulation modeling also requires a process description that can describe real-world conditions, one of which is the condition of the existing piping in the system. Failure scenarios caused a process to have abnormal conditions, allowing the alarm response time to be calculated, and it can be modelled by using the event scheduler facility In Aspen HYSYS. The HP scrubber's maximum alarm response time without pipe segments and with the addition of 16 m pipe segments are 2.42 minutes and 2.56 minutes. Meanwhile, the time from alarm to failure on the HP Scrubber without and with the addition of 16 m pipe are 13.60 minutes and 28.70 minutes, respectively. So, the length of segment pipes added to the pipe configuration does not really affect the alarm response time. However, it can affect the time until a process failure occurs.
Pengaruh Penambahan Polyvinyl Alcohol (PVOH) pada Biofoam dari Tepung Biji Nangka dan Ampok Jagung dengan Metode Thermopressing Yanis Fitrianti; Rheisya Talitha Azzahra; Endang Kusumawati; Keryanti
Jurnal Teknik Kimia USU Vol. 12 No. 2 (2023): Jurnal Teknik Kimia USU
Publisher : Talenta Publisher (Universitas Sumatera Utara)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.32734/jtk.v12i2.9228

Abstract

Starch and fiber-based biofoam as a solution to replace the role of styrofoam. However, the biofoam still unqualified as a good foam characteristic. Polyvinyl alcohol (PVOH) is added to improve the physical characteristics of biofoam. This study aims to determine the effect of PVOH addition on the quality of starch-based biofoam from jackfruit seeds and corn hominy. The gelatinization process was carried out using a mixer in 350 rpm speed at 100 °C for 5 minutes, then moulded in a thermopressing unit for 25 minutes at 100 °C. The characteristics of the material with amylose and amylopectin contents 17.30% and 31.60% respectively and corn hominy's fiber content at 2.72%. The best PVOH addition was 10% addition based on its characteristics from parameters such as water absorption, density, and biodegradability were close to Synbra Technology’s standard. However, all the physical and mechanical characteristics of the produced biofoam still can't reach the standard.
Co-Authors Endang Kusumawati Fahmi Nur Listiani Gianistri Maulani In Jumanda Kasdadi Keryanti, Keryanti Rheisya Talitha Azzahra