Garuda - Garba Rujukan Digital

Article Per Year (5 Year)

All

Journal of Earth Energy Science, Engineering, and Technology

jeeset
Website

Published by Universitas Trisakti

ISSN : 26153653 EISSN : 26140268 DOI : https://doi.org/10.25105/jeeset.v1i1

Core Subject : Science,

Energy

This journal intends to be of interest and utility to researchers and practitioners in the academic, industrial, and governmental institutions.

Arjuna Subject : Energi (semua kategori) - Energi Terbarukan, Keberlanjutan dan Lingkungan

Articles 6 Documents

Search results for , issue "Vol. 2 No. 3 (2019): JEESET VOL. 2 NO. 3 2019" : 6 Documents clear

Laboratory Studies to Increase Oil Production Using Methyl Ester Sulfonate Injection on X Field Aditya Rachman; Rini Setiati; Kartika Fajarwati Hartono
Journal of Earth Energy Science, Engineering, and Technology Vol. 2 No. 3 (2019): JEESET VOL. 2 NO. 3 2019
Publisher : Penerbitan Universitas Trisakti

The majority of petroleum production comes from the brown field where production has decreased from year to year in Indonesia. To increase the recovery factor of petroleum from the reservoir, an advanced step of production is required, Enhanced Oil Recovery (EOR), which can optimize the depletion of old oil fields. EOR is the application of technology that requires cost, technology and high risk. Therefore, before implementing EOR, in a field, we must carefully evaluate both technically and economically to obtain an optimal additional recovery. This research was conducted to increase oil production by injection of Methyl Ester Sulfonate (MES). This study begins with a screening parameter crude oil, formation water, Berea’s core, and determination of phase behavior, interfacial tension (IFT), thermal stability, imbibition, and core flooding tests. The result for concentratin optimum in 0.3% MES and had IFT 0.3267 dyne/cm. The results of core flooding tests are: Recovery factor of waterflooding is 33.95 % and recovery factor of MES injection is 4.19 %.

Reducing Hydrocarbon in Place Uncertainty in Akasia Bagus Structure as Potential Field and Redevelopment Review Tri Handoyo; Suryo Prakoso
Journal of Earth Energy Science, Engineering, and Technology Vol. 2 No. 3 (2019): JEESET VOL. 2 NO. 3 2019
Publisher : Penerbitan Universitas Trisakti

The success of the discovery of new structure Akasia Bagus with potential L layer in 2009 at PT Pertamina EP's Jatibarang Field was followed up by the drilling infill wells with Plan of Development (POD) mechanism which is currently in the process of drilling the last well. The basis of the L layer hydrocarbon calculation in place on the POD is a static analysis. The wells currently produced are still able to flow with natural flow and enough production data since 2009 this structure was found. This study will present an analysis of production in the L layer of Akasia Bagus structure for Original Oil In Place (OOIP) updates using the conventional material balance method and then carry out the best development strategy to optimize oil production. Economic analysis is also carried out for reference in making decision on which scenario to choose. The conventional material balance method gets an OOIP value of 17.36 MMSTB, with the drive energy ratio being 5:3:2 for water influx : fluid expansion : gas cap expansion. Three (3) production optimization scenarios were analyzed, the results showed that the addition of 2 infill wells reached Recovery Factot (RF) of oil up to 23% of OOIP, minimal water production and attractive economic results.

Flow Regime Analysis on Pressure Build-up Test Result of Z-01 Well Using Dual Porosity Reservoir Model Anggitya Hafidh; Muhammad Taufiq Fathaddin
Journal of Earth Energy Science, Engineering, and Technology Vol. 2 No. 3 (2019): JEESET VOL. 2 NO. 3 2019
Publisher : Penerbitan Universitas Trisakti

Flow regime analysis on the results of pressure build-up Z-01 well test was conducted to determine the type of flow that occurs in each time region section. In the early time stage there is a flow which is dominated by linear flow which is then followed by bilinear flow. At the middle time there is a radial flow where the pressure disturbance has spread towards the reservoir. In the late time flow stage is dominated by steadystate flow where the flow is affected because there is a support pressure caused by the constant pressure boundary. In the analysis of pressure build-up used to determine reservoir parameters can be used in the middle time region. This is used because the plot results between ΔP vs. log HTR (Horner Time Ratio) are straight lines which can be used to calculate reservoir parameter values such as permeability (k), formation damage factor (s). This test was analyzed using the Ecrin software and obtained a dual porosity model with a permeability value of 4.8 md, skin -3.57. From the analyzed model, it is obtained that the well fracture-finite conductivity model means that the Z-01 well has been stimulated to increase production.

Comparison of Rock Type Determination Based on Permeability Estimation and FZI Value in Upper Cibulakan Shaly Sand Formation, ASR Field Anditya Sapta Rahesthi; Ratnayu Sitaresmi; Sigit Rahmawan
Journal of Earth Energy Science, Engineering, and Technology Vol. 2 No. 3 (2019): JEESET VOL. 2 NO. 3 2019
Publisher : Penerbitan Universitas Trisakti

Rock permeability is an important rock characteristic because it can help determine the rate of fluid production. Permeability can only be determined by direct measurement of core samples in the laboratory. Even though coring gives good results, the disadvantage is that it takes a lot of time and costs so it is not possible to do coring at all intervals. So that the well log is required to predict the level of permeability indirectly. However, the calculation of permeability prediction using well log data has a high uncertainty value, so rock typing is required so that the calculation of permeability prediction becomes more detailed. This research was conducted in an effort to determine the Hydraulic Flow Unit (HFU) of the reservoir in the well that has core data using the Flow Zone Indicator (FZI) parameter and FZI value propagation on wells that do not have core data so that the type of rock and permeability value are obtained from every well interval. From the results of the study, the reservoirs on the ASR field can be grouped into six rock types. The six rock types each have permeability as a function of validated porosity by applying it at all intervals. After FZI is calculated from log data and validated with core data, it can be seen that the results of the method produce a fairly good correlation (R2 = 0.92). Furthermore, from the permeability equation values for each different rock type, the predicted permeability results are also quite good (R2 = 0.81).

Modification of DS-01 Drilling Fluid to Reduce Formation Damage Winarto S.; Sugiatmo Kasmungin
Journal of Earth Energy Science, Engineering, and Technology Vol. 2 No. 3 (2019): JEESET VOL. 2 NO. 3 2019
Publisher : Penerbitan Universitas Trisakti

In the process of drilling for oil and gas wells the use of appropriate drilling mud can reduce the negative impacts during ongoing drilling and post-drilling operations (production). In general, one of the drilling muds that are often used is conventional mud type with weighting agent barite, but the use of this type of mud often results in skin that is difficult to clean. Therefore in this laboratory research an experiment was carried out using a CaCO3 weigting agent called Mud DS-01. CaCO3 is widely used as a material for Lost Circulation Material so that it is expected that using CaCO3 mud will have little effect on formation damage or at least easily cleaned by acidizing. The aim of this research is to obtain a formula of mud with CaCO3 which at least gives formation damage. Laboratory experiments on this drilling mud using several mud samples adjusted to the property specifications of the mud program. Mud sample consists of 4, namely using super fine, fine, medium, and conventional CaCO3. First measuring mud properties in each sample then testing the filter cake breaker, testing the initial flow rate using 200 ml of distilled water and a 20 micron filter disk inserted in a 500 ml HPHT cell then assembled in a PPA jacket and injecting a pressure of 100 psi. The acidification test was then performed using 15% HCL and then pressured 100 psi for 3 hours to let the acid work to remove the cake attached to the filter disk (acidizing). Laboratory studies are expected which of these samples will minimize the formation damage caused by drilling fluids.

Optimization and Prediction of Sucker Rod Pump Performance on Well X-1 in Field X in the Future Mohammad Firdaus Sabaruddin; Ilman Muhammad Azmi; Callula Engrasia Fathoni Firdaus; Muhamad Reza Shahrazade
Journal of Earth Energy Science, Engineering, and Technology Vol. 2 No. 3 (2019): JEESET VOL. 2 NO. 3 2019
Publisher : Penerbitan Universitas Trisakti

The performance of the sucker rod pump is influenced by the characteristics of the well and reservoir such as pressure, well productivity, physical properties of the fluid, depth and diameter of the well. Therefore, pumping pumps need to be designed and optimized taking into account these conditions. As time goes on production changes in physical properties occur in the reservoir such as a decrease in reservoir pressure and a decrease in well productivity. Changes in the physical properties of the reservoir will affect the performance of the sucker rod pump. The purpose of this study is to design a sucker rod pump at X-1 well and forecast production in the future. The flow rate determination is obtained from the point of intersection between the pump intake pressure curve and IPR curves both in the present and in the future. In this study the pump speed is set at 10 SPM. Based on this method it was found that the well can produce with a flow rate of 1132 bpd with an oil flow rate of 27 bpd. The stroke length for this condition is 304 inch. Over time the production is estimated to cause the pressure to decrease to 1010 psi in 2040. The decrease in reservoir pressure causes the reduction in the flow rate of sucker rod pump to 1046 bpd with an oil flow rate of 14.6 bopd. So that the magnitude of the reduction in the flow rate of liquid between 2019 and 2040 was 7.6%, while the decrease in the oil flow rate was 45.9%. If the speed is set at 10 SPM, the stroke length needs to be reduced with time. The stroke length was designed to be 304 inches in 3019 and reduced to 281 inches in 2040.

Page 1 of 1 | Total Record : 6

Filter by Year

2019 2019

Filter By Issues

All Issue Vol. 6 No. 2 (2023): JEESET VOL. 6 NO. 2 2023 Vol. 6 No. 1 (2023): JEESET VOL. 6 NO. 1 2023 Vol. 5 No. 3 (2022): JEESET VOL. 5 NO. 3 2022 Vol. 5 No. 2 (2022): JEESET VOL. 5 NO. 2 2022 Vol. 5 No. 1 (2022): JEESET VOL. 5 NO. 1 2022 Vol. 4 No. 3 (2021): JEESET VOL. 4 NO. 3 2021 Vol. 4 No. 2 (2021): JEESET VOL. 4 NO. 2 2021 Vol. 4 No. 1 (2021): JEESET VOL. 4 NO. 1 2021 Vol. 3 No. 3 (2020): JEESET VOL. 3 NO. 3 2020 Vol. 3 No. 2 (2020): JEESET VOL. 3 NO. 2 2020 Vol. 3 No. 1 (2020): JEESET VOL. 3 NO. 1 2020 Vol. 2 No. 3 (2019): JEESET VOL. 2 NO. 3 2019 Vol. 2 No. 2 (2019): JEESET VOL. 2 NO. 2 2019 Vol. 2 No. 1 (2019): JEESET VOL. 2 NO. 1 2019 Vol. 1 No. 3 (2018): JEESET-VOL.1-NO.3-2018 Vol. 1 No. 2 (2018): JEESET-VOL.1-NO.2-2018 Vol. 1 No. 1 (2018): JEESET-VOL.1-NO.1-2018 More Issue

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
Muhammad Taufiq Fathaddin

Contact Email
muh.taufiq@trisakti.ac.id

Phone
+6285770946165

Journal Mail Official
jeeset_mtp@trisakti.ac.id

Editorial Address
Program Studi Magister Teknik Perminyakan (Master of Petroleum Engineering) Fakultas Teknologi Kebumian dan Energi Universitas Trisakti Gedung D Lantai 5 Universitas Trisakti, Jalan Kyai Tapa No.1 Grogol, Jakarta Barat, 11440, Indonesia.

Location
Kota adm. jakarta barat,

Dki jakarta

INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name Muhammad Taufiq Fathaddin

Contact Email muh.taufiq@trisakti.ac.id

Phone +6285770946165

Journal Mail Official jeeset_mtp@trisakti.ac.id

Editorial Address Program Studi Magister Teknik Perminyakan (Master of Petroleum Engineering) Fakultas Teknologi Kebumian dan Energi Universitas Trisakti Gedung D Lantai 5 Universitas Trisakti, Jalan Kyai Tapa No.1 Grogol, Jakarta Barat, 11440, Indonesia.

Location Kota adm. jakarta barat, Dki jakarta INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Contact Name
Muhammad Taufiq Fathaddin

Contact Email
muh.taufiq@trisakti.ac.id

Phone
+6285770946165

Journal Mail Official
jeeset_mtp@trisakti.ac.id

Editorial Address
Program Studi Magister Teknik Perminyakan (Master of Petroleum Engineering) Fakultas Teknologi Kebumian dan Energi Universitas Trisakti Gedung D Lantai 5 Universitas Trisakti, Jalan Kyai Tapa No.1 Grogol, Jakarta Barat, 11440, Indonesia.

Location
Kota adm. jakarta barat,

Dki jakarta

INDONESIA