Article Per Year (5 Year)
p-Index From 2019 - 2024
0.61
P-Index
This Author published in this journals
All Journal Journal of Renewable Energy, Electrical, and Computer Engineering
Isa, Muzamir
Unknown Affiliation
Computer Science & IT Control & Systems Engineering Electrical & Electronics Engineering Energy Engineering

Published : 3 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 3 Documents
Search

 1 
Economic Dispatch Analysis Using Equal Incremental Cost Method with Linear Regression Approach Hasibuan, Arnawan; Kurniawan, Robi; Isa, Muzamir; Mursalin, Mursalin
Journal of Renewable Energy, Electrical, and Computer Engineering Vol 1, No 1 (2021): March 2021
Publisher : Institute for Research and Community Service, Universitas Malikussaleh, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29103/jreece.v1i1.3617

Abstract

The use of fuel is one thing that needs special attention, because most of the operating costs of a plant are fuel costs. One of the efforts to minimize the cost of generating fuel is called Economic dispatch. In this study, an Equal Incremental Cost method with a Linear Regression approach will be presented to obtain a minimum generation cost. The case taken is the Pangkalan Susu PLTU which operates two generating units. Based on the results of calculations using the Equal Incremental Cost method with the Linear Regression approach, the cost is -0.033% or an average of -13,111 $/hour.
The Effect of Distributed Generator Injection with Different Numbers of Units on Power Quality in the Electric Power System Kurniawan, Robi; Nasution, Ardiansyah; Hasibuan, Arnawan; Isa, Muzamir; Gard, Muskan; Bhunte, Shrikant Vasantrao
Journal of Renewable Energy, Electrical, and Computer Engineering Vol 1, No 2 (2021): September 2021
Publisher : Institute for Research and Community Service, Universitas Malikussaleh, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29103/jreece.v1i2.5236

Abstract

Distributed Generation (DG) is a small capacity generator located in the electricity distribution system and is usually placed on buses that are connected directly to the load. Placement of distributed generation is one of the technical efforts to reduce voltage drop and power losses in the system. In addition, load flow analysis is a study to plan and determine the amount of power in an electric power system. The results of power losses after adding distributed generation were the best in the fifth experiment on bus 149, where the system experienced a total loss of active power (P) previously of 720,822 kW, to 682,939 kW and total loss of reactive power (Q) previously of 530.02 kVar, to 405.835 kVar. From the results of the calculation of the power flow using ETAP software (Electrical Transient Analyzer Program). So, it can be concluded that the electrical network system can be said to be good. The results obtained are the more DG (wind turbine generator) that is input into the bus it will reduce the voltage drop that occurs. After simulating the overall voltage drop, it still meets the standards according to the results of the Text Report on ETAP.
Heater lamp product design as hypothermia prevention using qfd (quality function deployment) Subhan, Subhan; Anshar, Khairul; Muarif, Agam; Ningtiyas, Dinda; Pandey, Govinda Prashad; Isa, Muzamir
Journal of Renewable Energy, Electrical, and Computer Engineering Vol 2, No 1 (2022): March 2022
Publisher : Institute for Research and Community Service, Universitas Malikussaleh, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29103/jreece.v2i1.6630

Abstract

Every year the number of climbers increase, there are at least 70,000 climbers including researchers. The increase in the number of climbers will certainly increase the mortality risk of hypothermia. At least 18 people died from hypothermia in 2014 to 2015. The risk of hypothermia can be reduced by handling such as providing warmth to the patient. Warmth can be created by using a tool that produces the right heat, easy and safe to use, easy to carry and also affordable. This is the basis for researches to conduct research on designing heating products in tents as an effort to prevent hypothermia. This research uses the QFD (Quality Function Deployment) method in processing the results of the consumer’s voice, design the product concept, screening and selecting concept and analysis the final product design. Based on the data collection and processing that has been carried out, there are 10 criteria for consumer needs and interests for product, including practical tools to carry, safe to use, can warm the body to have additional functions as cellphone chargers. While the alternative concept chosen in the form of cylindrical tube, using a Li-ion battery, and a frame made of polypropilene plastic. From the chosen concept, then a heating lamp model is designed in the display when used and stored.
Co-Authors Arnawan Hasibuan Bhunte, Shrikant Vasantrao Gard, Muskan Khairul Anshar Muarif, Agam Nasution, Ardiansyah Ningtiyas, Dinda Pandey, Govinda Prashad Robi Kurniawan Subhan A Gani Yundari, Yundari