Garuda - Garba Rujukan Digital

FABRIKASI SERAT NANO BERBASIS POLIMER MENGGUNAKAN TEKNOLOGI ELECTROSPINNING Hentihu, M. Fahrur Rozy; Sholahuddin, Imam
ROTOR Vol 8, No 1 (2015)
Publisher : ROTOR

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (239.886 KB)

Nano fibers can be fabricated using electrospinning technology using local components at low cost. Electrospinning technology also has advantages to control the morphology, uniformity, porosity and composition of nano fiber by pumping a solution of the gel through the nozzle of a metal-needle high voltage electrified. Based on the results of the research, the general parameters required for the manufacture of electrospinning machine is a resolution rate of spraying the solution (Î¼â / min) and the magnitude of the high voltage power source (kV). A human hair is approximately 60 Î¼m size looks larger than the size of the resulting PVA fiber electrospinning machine. These results were confirmed by the results of fiber characterization using the AFM in the area of ââfiber 50 Î¼m x 50 Î¼m, fiber size in the range of <1 Î¼m are included in the order of 1000 nm. It can be concluded that the electrospinning machine that has been made in this study has been able to create nanometer-scale fibers.

FABRIKASI DAN KARAKTERISASI NANOGENERATOR BERBASIS NANOFIBER-NANOWIRE ZnO Sholahuddin, Imam; Hentihu, M. Fahrur Rozy
ROTOR Vol 8, No 1 (2015)
Publisher : ROTOR

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (238.356 KB)

Fiber diffusion process when the fiber is still green on a plate collector and the thermal decomposition process followed by the formation of ZnO crystal nucleation has a very large role of the morphology of the final form of fiber products. Conversely, a positive result occurs in nanowire growth process. At the time of natural air pressure conditions and the presence of oxygen in the air in the process of sintering for 2 hours without using a catalyst, ZnO crystals can grow by itself (self-growth) into a nanowire. As a material nanogenerator, this situation provides an additional active area to excite the tap-off force into electrical voltage of up to 234.55 mV (2 Î¼â / min).

Variasi Ukuran terhadap Kekerasan dan Laju Keausan Komposit Epoxy Alumunium-Serbuk Tempurung Kelapa untuk Kampas Rem Taka, Ario Kristian; Kristianta, FX.; Sholahuddin, Imam
Jurnal Rekayasa Mesin Vol 8, No 3 (2017)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

The aim of this research was to investigate the influence of the particle size of coconut shell powder on hardness and wear rate om aluminium epoxy based composite. Experimental method was used in this study by using four configurations of particle size. The configuration includes comersial powder and particle size of 300 Âµm, 425 Âµ and 600 Âµm. The results showed that the highest and smallest hardness value obtained by 300 Âµm of 63.67 kg/mm2 and 600 Âµm is 41.67 kg, respectively. However, the highest and smallest wear rate obtained by 600 Âµm is 8,70 x 10-6 gram/s.mm2 and 300 Âµm is 1,17 x 10-6 gram/s.mm2, respectively. This phenomena occured due to the coconut shell powder size of 300 Âµm is well and uniformly spread.

IbM Kelompok Petani Tebu Rakyat di Kecamatan Semboro, Kabupaten Jember Ummi Sholikhah; Imam Sholahuddin
Asian Journal of Innovation and Entrepreneurship Vol 4 No 01 (2015): January 2015
Publisher : UII

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.20885/ajie.vol4.iss1.art6

Sub-district Semboro is a strategic region for the development of sugarcane Agricultural commodities. According to the Central Bureau of Statistics Jember in 2008, the area under sugarcane cultivation in the district Semboro in 2008 approximately 491 acres, in the District Semboro also contained relatively large sugar mills and has the ability milling capacity of 70 thousand quintals or 7000 TCD ( Tones Cine Day ) with the extensive area of sugarcane commodities land, the availability of seed cane is also needed single bud planting method that is one of the breakthrough to overcome the problems in the nursery. In principle, a single bud planting method is to use a chip nursery development / potray with the buds. This can save planting materials, land and time in the nursery and produce quality seeds.In the early stages of implementation IbM activities that began in April 2014 until now is still running smoothly without significant obstacles, so that every transfer of science and technology that is given to the partners can be accepted and implemented, plan future activities are the stages of the transfer of seed cane single bud results in PII in moving to production fields, and will be doing the evaluation of any activity undertaken. Keywords: IbM, Semboro , Single Bud Planting

ORIENTASI SUDUT LILITAN BENANG KATUN TERHADAP KEKUATAN TARIK PADA PIPA KOMPOSIT FILAMENT WINDING Ardian Dwi Saputra; M. Fahrur Rozy H; Agus Triono; Imam Sholahuddin
ROTOR Vol 10 No 1 (2017)
Publisher : Jurusan Teknik Mesin Fakultas Teknik Universitas Jember

Cotton fibers currently use in many industries textiles, easy gotten in the market, and a cheap price. Using of fiber would be able to solve the environtment problems, reduce the metal using, particularly in the oil and gas industries. In this study, composite pipes are made by cotton fibers as reinforcement, particles of montmorillonite as filler, and unsaturated polyester as matrix. From that consideration this study was conducted to obtain that analysis of tensile strength composite cotton fibers. With the pattern of variation woven fiber direction angle towards the corner fibers 450, 550, 650, 750, and 850. From the test results the highest tensile strength values is obtained by a composite pipe with fiber direction angle of 850. The test results showed that the tensile strength of the cotton fiber reinforced composite pipe with direction of 450 angle fiber is 3.76 MPa, for direction of 550 angle fiber tensile strength is 1.28 MPa, for direction of 650 angle fiber tensile strength is 10.691 Mpa, for direction of 750 angle fiber tensile strength is 14.465 Mpa, and for direction of 850 angle fiber tensile strength 28.617 MPa. Keywords: Cotton fiber, unsaturated polyester, filament winding method, montmorillonite, Tensile Strength

FABRIKASI SERAT NANO BERBASIS POLIMER MENGGUNAKAN TEKNOLOGI ELECTROSPINNING M. Fahrur Rozy Hentihu; Imam Sholahuddin
ROTOR Vol 8 No 1 (2015)
Publisher : Jurusan Teknik Mesin Fakultas Teknik Universitas Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (239.886 KB)

Nano fibers can be fabricated using electrospinning technology using local components at low cost. Electrospinning technology also has advantages to control the morphology, uniformity, porosity and composition of nano fiber by pumping a solution of the gel through the nozzle of a metal-needle high voltage electrified. Based on the results of the research, the general parameters required for the manufacture of electrospinning machine is a resolution rate of spraying the solution (μℓ / min) and the magnitude of the high voltage power source (kV). A human hair is approximately 60 μm size looks larger than the size of the resulting PVA fiber electrospinning machine. These results were confirmed by the results of fiber characterization using the AFM in the area of fiber 50 μm x 50 μm, fiber size in the range of <1 μm are included in the order of 1000 nm. It can be concluded that the electrospinning machine that has been made in this study has been able to create nanometer-scale fibers.

FABRIKASI DAN KARAKTERISASI NANOGENERATOR BERBASIS NANOFIBER-NANOWIRE ZnO Imam Sholahuddin; M. Fahrur Rozy Hentihu
ROTOR Vol 8 No 1 (2015)
Publisher : Jurusan Teknik Mesin Fakultas Teknik Universitas Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (238.356 KB)

Fiber diffusion process when the fiber is still green on a plate collector and the thermal decomposition process followed by the formation of ZnO crystal nucleation has a very large role of the morphology of the final form of fiber products. Conversely, a positive result occurs in nanowire growth process. At the time of natural air pressure conditions and the presence of oxygen in the air in the process of sintering for 2 hours without using a catalyst, ZnO crystals can grow by itself (self-growth) into a nanowire. As a material nanogenerator, this situation provides an additional active area to excite the tap-off force into electrical voltage of up to 234.55 mV (2 μℓ / min).

PENGARUH KONSENTRASI INHIBITOR UBI UNGU TERHADAP LAJU KOROSI BAJA KARBON A53 DENGAN MEDIA AIR LAUT Ridho Unggul Nur Rahmadi; Imam Sholahuddin; Dwi Djumhariyanto
ROTOR Vol 10 No 2 (2017)
Publisher : Jurusan Teknik Mesin Fakultas Teknik Universitas Jember

Corrosion is a form of damage that occurs in metals. The main factor is the cause of the corrosion environment. A53 steel is a type of low carbon steel and a steel material types that are widely used for pipe applications. The use of a corrosion inhibitor is one way of preventing corrosion. Anthocyanin substances contained in purple yam can be made in a natural inhibitor, because the substance is an antioxidant anthocyanin which is an oxidation inhibitor. Variables used were varied concentration of 0 ppm, 2000 ppm, 4000 ppm and 6000 ppm. This study aims to determine the rate of corrosion, purpel sweet potato extract efficiencies and changes in microstructure. The method used in this study is experimental, inhibitor efficiency analysis, ANOVA test and analysis micro photo. The results showed that the material is corroded by pitting corrosion and uniform shape. Values on concentration lowest corrosion rate of 0.0044 mmpy 6000 ppm and 6000 ppm at the highest efficiency of 72.70%. Keywords: anthocyanin, steel A53, natural inhibitor, purple sweet potato.

PENGARUH LAJU PREKURSOR SERBUK ALUMINIUM TERHADAP BENTUK MORFOLOGI NANOPARTIKEL ALUMINA DENGAN METODE THERMAL PLASMA Havid Arifian Rochman; Arief Ginanjar Dirgantara; Salahudin Junus; Imam Sholahuddin; Aris Zainul Muttaqin
ROTOR Vol 10 No 1 (2017)
Publisher : Jurusan Teknik Mesin Fakultas Teknik Universitas Jember

The synthesis of nanoparticles using thermal DC plasma method is a simple method for ease of installation and high efficiency is due to the rate of precursor that can be controlled. Micro-sized aluminum powder is synthesized using thermal DC plasma undergoing a process of evaporation as it passes through high temperature plasma flame, where kemuadian oxidized aluminum particles which evaporates the particles are split and binds with oxygen to form aluminum oxide or also known as alumina (Al2O3). In this experiment, the flow rate of oxygen plasma parameters at 35 SCFH (Standard Cubic Feet per Hour) and 20 amperes flows with precursors rate variation of 1.16 g / min, 3.19 g / min, and 3.5 g / min. Precursors used is 88 micro sized aluminum powder. To determine the morphology of nanoparticles of alumina testing scanning electron microscopy (SEM), the morphology form of nanosphere. Results of the analysis showed that the rate of precursor low causing agglomeration level slightly while the higher rate of precursor agglomeration rate also increased. At the rate of precursor 1.16 g / min, nanoparikel undergo agglomeration with an average particle size of 36.55 nm, and then at a rate of 3.19 gr precursor / mnt an average particle size of 46.49 nm, and at a rate of 3.5 gr / mnt an average particle size of 46.49 nm. The powder nanoparticles were then characterized using X-ray defraksi (XRD) where all alumina nanoparticles were synthesized showed alumina phase that is formed is a phase δ-Al2O3. Keywords: Alumina nanoparticles, DC Thermal Plasma, morphology, precursor rate, nanoparticles size, SEM, XRD.

PENGARUH PROSES HYDROTHERMAL NANOFIBER ZnO TERHADAP UNJUK KERJA DYE – SENSITIZED SOLAR CELL (DSSC) Dimas Ilham Rasyid; Harry Sutjahjono; Imam Sholahuddin
STATOR: Jurnal Ilmiah Mahasiswa Teknik Mesin Vol 1 No 1 (2018): JURNAL STATOR
Publisher : STATOR: Jurnal Ilmiah Mahasiswa Teknik Mesin

Show Abstract | Download Original | Original Source | Check in Google Scholar

Solar energy can be utilized as renewable energy, because fossil energy is increasingly depleted and also environmentally friendly. In this case DSSC photovoltaic devices are used to convert photon energy into electricity. The DSSC in this study consisted of alfafa leaf extract dye, nanofiber and nanowire ZnO semiconductor, iodine electrolyte, and FTO conductive glass. The method used in fabrication of ZnO nanofiber using electrospinning method, while for fabrication of nanofiber / nanowire ZnO using electrospinning method and continued with hydrothermal process. The hydrothermal process generates nanowire in ZnO nanofiber, so the active area of the ZnO semiconductor increases. With a large active area will increase the efficiency of the DSSC. ZnO nanofiber monomers and nanofiber / nanowire ZnO were characterized using SEM, while DSSC performance was tested under a 1000W halogen lamp. The DSSC is made with 2 layer, 3 layer, 4 layer and 5 layer nanofiber layers resulting in efficiency of 0.0030%, 0.0076%, 0.0103% and 0.0082% respectively. While DSSC with semiconductor nanofiber / nanowire ZnO 2 layer, 3 layer, 4 layer and 5 layer yield efficiency consecutively equal to 0,0067%, 0,0163%, 0,0747%, 0,0025%. The final results show that semiconductors with an increased active area on the ZnO nanofiber / nanowire structure will improve DSSC performance. Keywords: dye – sensitized solar cell (DSSC), active area, ZnO nanofiber, ZnO nanofiber/nanowire, hydrothermal process

Title

Found 17 Documents
Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title Search

Found 17 Documents Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title

Found 17 Documents
Search