Article Per Year (5 Year)
p-Index From 2019 - 2024
0
P-Index
This Author published in this journals
All Journal Fibusi (Jurnal Online Fisika) Jurnal Elektronika dan Telekomunikasi Teknologi Indonesia Makara Journal of Technology
Erlyta Septa Rosa
Pusat Penelitian Elektronika dan Telekomunikasi-Lembaga Ilmu Penelitian Indonesia (PPET-LIPI)
Chemical Engineering, Chemistry & Bioengineering Civil Engineering, Building, Construction & Architecture Computer Science & IT Electrical & Electronics Engineering Engineering Materials Science & Nanotechnology Mechanical Engineering Physics

Published : 5 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 2 Documents
Search
Journal : Jurnal Elektronika dan Telekomunikasi

 1 
Analysis of Thermal Treatment Zirconia as Spacer Layer on Dye-Sensitized Solar Cell (DSSC) Performance with Monolithic Structure Anwar, Chairil; Rosa, Erlyta Septa; Shobih, Shobih; Hidayat, Jojo; Tahir, Dahlang
Jurnal Elektronika dan Telekomunikasi Vol 18, No 1 (2018)
Publisher : Indonesian Institute of Sciences

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14203/jet.v18.21-26

Abstract

Monolithic dye-sensitized solar cells (DSSC) offer the prospect of lower material cost and require a simpler manufacturing process compared with conventional DSSC. Fabricated on a single fluorine tin oxide (FTO) glass substrate consists of a nanoporous TiO2 photoanode layer, a ZrO2 spacer layer, a carbon counter electrode layer, a dye, and an electrolyte. The spacer layer on the monolithic DSSC serves as electrolyte storage and insulating layer to separate between photoanode and counter electrode. Zirconia is often used as a spacer because it has high temperature resistant properties, high dielectric constant and adhesive as an insulator that has band gap between 5-6 eV. The effects of the thermal treatment of zirconia layer as a spacer electrolyte on the performance of monolithic DSSC have been investigated. The cell’s performance increases with the sintering temperature as well as indicated by the decreased in particle size and increased in quantum efficiency in the absorption region of the titania layer. Co-sintering treatment tends to drastically reduce cell’s performance. The highest performance was obtained at a temperature sintering of 500o C with an PCE of 0.22%, Isc = 0.16 mA and Voc = 0.71 V.
Fabrication of Hybrid Polymer Solar Cells By Inverted Structure Based on P3HT:PCBM Active Layer Shobih, Shobih; Abdillah, Rizky; Rosa, Erlyta Septa
Jurnal Elektronika dan Telekomunikasi Vol 17, No 1 (2017)
Publisher : Indonesian Institute of Sciences

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14203/jet.v17.13-18

Abstract

Hybrid polymer solar cell has privilege than its conventional structure, where it usually has structure of (ITO/PEDOT:PSS/Active Layer/Al). In humid environment the PEDOT:PSS will absorb water and hence can easily etch the ITO. Therefore it is necessary to use an alternative method to avoid this drawback and obtain more stable polymer solar cells, namely by using hybrid polymer solar cells structure with an inverted device architecture from the conventional, by reversing the nature of charge collection. In this paper we report the results of the fabrication of inverted bulk heterojunction polymer solar cells based on P3HT:PCBM as active layer, utilizing ZnO interlayer as buffer layer between the ITO and active layer with a stacked structure of ITO/ZnO/P3HT:PCBM/PEDOT:PSS/Ag. The ZnO interlayer is formed through short route, i.e. by dissolving ZnO nanoparticles powder in chloroform-methanol solvent blend rather than by sol-gel process. Based on the measurement results on electrical characteristics of inverted polymer solar cells under 500 W/m2 illumination and AM 1.5 direct filter at room temperature, cell with annealing process of active layer at 110 °C for 10 minutes results in higher cell performance than without annealing, with an open-circuit voltage of 0.21 volt, a short-circuit current density of 1.33 mA/cm2 , a fill factor of 43.1%, and a power conversion efficiency of 0.22%. The low cell’s performance is caused by very rough surface of ZnO interlayer.
Co-Authors Abdillah, Rizky Brian Yuliarto Chairil Anwar Dahlang Tahir Jojo Hidayat Lia Muliani Shobih . Shobih Shobih Shobih, - Zeniar Rossa Pratiwi