Article Per Year (5 Year)
p-Index From 2019 - 2024
1.006
P-Index
This Author published in this journals
All Journal Jurnal Ilmu Pertanian Indonesia Jurnal Biologi Tropis Jurnal SIAR ILMUWAN TANI Agroteksos Jurnal Malikussaleh Mengabdi DEVOTE: Jurnal Pengabdian Masyarakat Global
Fauzan Fahrussiam
Universitas Mataram
Religion Agriculture, Biological Sciences & Forestry Humanities Biochemistry, Genetics & Molecular Biology Computer Science & IT Decision Sciences, Operations Research & Management Economics, Econometrics & Finance Education Engineering Environmental Science Immunology & microbiology Law, Crime, Criminology & Criminal Justice Social Sciences Other

Published : 7 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 1 Documents
Search
Journal : Jurnal Ilmu Pertanian Indonesia

 1 
Karakteristik Aus Mata Pisau Terlapisi Bahan Pengeras pada Pemotongan Kayu Mersawa dan Papan Partikel Fauzan Fahrussiam; Wayan Darmawan; Imam Wahyudi; Hiroshi Usuki; Masahiro Yoshinobu; Shuhou Koseki
Jurnal Ilmu Pertanian Indonesia Vol. 20 No. 3 (2015): Jurnal Ilmu Pertanian Indonesia
Publisher : Institut Pertanian Bogor

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1305.769 KB) | DOI: 10.18343/jipi.20.3.223

Abstract

The use of mersawa wood and particleboard as a materials has been increasing for building constructions and decorative purpose. In previous study reported that, these materials provide a high rate of wear caused by abrasion (high silica) and resin content. This article presents the characteristics of wear on the clearance face of newly multilayer-coated K10 cutting tools when milling mersawa wood and particleboard. The K10 cutting tools were coated with monolayer titanium aluminum nitride (TiAlN), multilayer TiAlN/titanium silicon nitride (TiSiN), and TiAlN/titanium boron nitride (TiBN). Mersawa wood with density of 0.80 g/cm3 and particleboard with a density of 0.61 g/cm3 were cut using the coated tools and uncoated K10. Cutting tests were performed on computer numeric control router at a high cutting speed of 17 m/s and a feed rate of 0.1 mm/rev to investigate the wear characteristics on the clearance face of these coated tools. Result of research shown that the coated tools experienced a smaller amount of wear than the uncoated tool when cutting the mersawa and particleboard. The best coating among other coated in this study was multilayer TiAlN/TiBN. The high hardness, low coefficient of friction, high resistance to oxidation, and high resistance to delamination wear of the multilayer-coated TiAlN/TiBN tool indicate a very promising applicability of this coating for high-speed cutting of abrasive woods and wood based materials.
Co-Authors A.A. Ketut Agung Cahyawan W Andrie Ridzki Prasetyo Andrie Ridzki Prasetyo Andrie Ridzki Prasetyo Baiq Elok Salsabila Halimah Dini Lestari Dini Lestari Dini Lestari Harits Firmansyah Hasyyati Shabrina Hasyyati Shabrina Hasyyati Shabrina Hiroshi Usuki I Wayan Darmawan Lestari, Andi Tri Masahiro Yoshinobu Maulia Hidayati Muhammad Irham Musdi Musdi Musdi Musdi Musdi Nurul Chaerani Nurul Chaerani Nurul Chaerani Ratna Ayu Istiani Rima Vera Ningsih Rima Vera Ningsih Shuhou Koseki Sofia Mustamu