Article Per Year (5 Year)
p-Index From 2019 - 2024
0
P-Index
This Author published in this journals
All Journal Jurnal Teknologi Jurnal Rekayasa Jurnal Rekayasa Sipil dan Desain ROTOR: JURNAL ILMIAH TEKNIK MESIN
Hadi Ali
Unknown Affiliation
Automotive Engineering Civil Engineering, Building, Construction & Architecture Computer Science & IT Electrical & Electronics Engineering Energy Industrial & Manufacturing Engineering Materials Science & Nanotechnology Mechanical Engineering Other

Published : 13 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 8 Documents
Search
Journal : Jurnal Rekayasa Sipil dan Desain

 1 
Optimalisasi Tebal Perkerasan Pada Pekerjaan Pelebaran Jalan dengan Metode MDPJ 02/M/BM/2013 dan Pt T-01-2002-B Andriansyah Andriansyah; Priyo Pratomo; Hadi Ali
Jurnal Rekayasa Sipil dan Desain Vol 4, No 1 (2016): Edisi Maret 2016
Publisher : Jurnal Rekayasa Sipil dan Desain

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Every year, goverment incur huge cost for development of facilities and infrastructures oftransportation, especially land transportation development by increasing the road capacity. Thiscapacity expansion is done by widening the road, especially on roads that can no longeraccommodate the volume of vehicles or roads that predicted will be passed by the high volume ofvehicles. Therefore, it is required pavement thickness design solutions that based on a life cyclecost analysis and the lowest consideration of construction resources to the minimum life cycle costdesign.This research was conducted in A. H. Nasution Street, on Metro - Gedung Dalam segment. Todetermine the flexible pavement thickness, this research uses “Manual Desain Perkerasan Jalan02/M/BM/2013”, “Pedoman Perencanaan Tebal Perkerasan Lentur Pt T-01-2002-B” and“Perencanaan Tebal Perkerasan Lentur Jalan Raya dengan Metode Analisa Komponen 387-KPTS-1987 methods”. After that, analyze the road deterioration that will happen during the lifedesign or life cycle design that based on the value of IRI. The results of life cycle design wasdeveloped to get the best pavement type that based on the life cycle cost analysis.From the analysis that has been done, the design with the lowest initial cost is a pavement designby using Bina Marga Pt-T-01-2002-B method, whereas the design with the lowest life cycle cost isa pavement design by using MDPJ 02/M/BM/2013 method and the most optimal pavementthickness.Keywords : flexible pavement, life cycle cost, life cycle design, IRI
Perubahan Parameter Parameter Marshal Akibat Perbedaan Jumlah Tumbukan pada Aspal Concrete – Wearing Course (ACWC) Gradasi Halus Teguh Dwi Istanto; Priyo Pratomo; Hadi Ali
Jurnal Rekayasa Sipil dan Desain Vol 3, No 2 (2015): Edisi Juni 2015
Publisher : Jurnal Rekayasa Sipil dan Desain

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

This study was conducted to see the changes in the value of the parameter values marshall afterthe number of collisions in the standards vary the amount of the collision then analyzed thenumber of collision and then analyzed the number of collisions are most effective assessed on thevalue of the characteristic marshall. In the Marshall planning standard for the number ofcollisions of heavy traffic conditions compaction test specimen as 2x75 collision with a mixturecavity boundary between 3.5-5%.This study uses gradation Asphalt Concrete - Wearing Course (AC-WC) smooth gradations formiddle and upper limits. From the data obtained aggregate gradation and asphalt aggregatedemand needs are used to find the optimum bitumen content that is used in the manufacture of testspecimens for variations in the number of collisions is 2x55, 2x65, 2x75, 2x85, and 2x95. Marshallthen test to see the number of collisions are most effective against the characteristics of asphaltmixture.Based on the analysis of the data processing is obtained that the value content of asphalt is used tolimit the middle that is 5.7% and the upper limit of 6.5%. Total Collision 2x75 and 2x85 that meetsall the parameters marshall. For the number of collisions 2x55 and 2x65 obtained small stability,voids In The Mix (VIM) is great and does not make the specification, to the number of collisions2x95, obtained great stability and voids In The Mix (VIM) is small and does not get in thespecification.Keywords: Collision, Marshall, Asphalt Concrete - Wearing Course (AC-WC), Smooth Gradation
Pengaruh Suhu Tumbukan pada Campuran Aspal Beton dengan Jenis Lapis AC-WC Gradasi Halus Wahyudi Wahyudi; Priyo Pratomo; Hadi Ali
Jurnal Rekayasa Sipil dan Desain Vol 3, No 2 (2015): Edisi Juni 2015
Publisher : Jurnal Rekayasa Sipil dan Desain

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

This study was conducted to determine the effect of temperature on the Marshall parameterscompaction to mix AC - WC subtle gradations central limit. Optimum Asphalt Content Value(KAO) in the study sought to use 15 samples and done in the laboratory of Highway University ofLampung. From the analysis of the Marshall parameters obtained KAO mixture is 5.7%. Marshallparameter data retrieval is done twice trials, each experiment using 2x24 samples with the sametreatment for each experiment. Compaction temperature is 120 o C-155 o C is reviewed by varasi5 o C.From the results of experiments that have been conducted, Marshall parameter valuesobtained in experiment 1 and experiment 2 is not too much different. In general, the Stability,Flow, VMA and VFA qualify specifications bina marga 2010, the MQ does not meet thespecifications of 135 o C or lower temperatures and VIM value does not meet the specifications of130 o C or lower temperatures.Based on the tendency of marshall parameter values obtained fromexperiment 1 and experiment 2 indicate that the data obtained from these experiments hasparticularly a small false possibility.Keywords: AC-WC, KAO, Marshall parameter, temperature compaction,
Studi Kuat Tekan Batu Bata Menggunakan Bahan Additive (Abu Sekam Padi, Abu Ampas Tebu dan Fly Ash) Berdasarkan Spesifikasi Standar Nasional Indonesia (SNI) Abdurrohmansyah Abdurrohmansyah; Idharmahadi Adha; Hadi Ali
Jurnal Rekayasa Sipil dan Desain Vol 3, No 3 (2015): Edisi September 2015
Publisher : Jurnal Rekayasa Sipil dan Desain

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Brick is one of construction materials of building, shopping complex, real estate etc. Brick is madefrom the mixing of soil and water. In this study, the process of brick production will be tired by mixthe soil with additive materials such as rice husk ash, baggase ash and fly ash. It’s to know howbig the advantage of those additive materials and to compare the compressive strength betweenconventional brick and the brick that have mixed with rice husk ash, baggase ash and fly ash toget Indonesian National Standard for the strong and durable brick.Clay was used as the soil sample in this study. The clay is from Yoso Mulyo Village, Metro. Theadditive materials such as, rice husk ash is from Yoso Mulyo Village Metro, baggase ash is fromPT Indo Lampung Perkasa and the fly ash is from PLTU Tarahan.The result of this study show that the production of brick after burned using additive materialssuch as rice husk ash, baggase ash and fly ash, increase the compressive strength value. So, thestrength of the brick is good enough fulfilled the standard of Indonesian National StandardInstitution.Keywords: Brick, additive fly ash and rice husk ash, baggase ash, compressive strength
Pengaruh Suhu Pemadatan Campuran Untuk Perkerasan Lapis Antara (AC-BC) Budi Raharjo; Priyo Pratomo; Hadi Ali
Jurnal Rekayasa Sipil dan Desain Vol 4, No 1 (2016): Edisi Maret 2016
Publisher : Jurnal Rekayasa Sipil dan Desain

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

The main objective of this study was to determine the influence of variations of temperaturechanges on the asphalt compaction process heat (hot mix asphalt) layer between (AC - BC)against Marshall parameter with reference to the specifications of Highways in 2010.Based on the analysis of data processing obtained that the value content of asphalt used formiddle limit is 6.1 % and the lower limit of 6.85 %.Based on the analysis of data processing obtained that the value content of asphalt used formiddle limit is 6.1 % and the lower limit of 6.85 %. From the test results Marshall at atemperature of 135oC, 145oC and 155oC in the middle limit has met all the parameters Marshall.Only at a temperature of 125oC and 115oC that do not meet the parameters Marshall Void in valuedue Mix (VIM) and the Marshall Quotient (MQ) do not enter Specifications Highways Marshall2010. While testing the lower limit on the temperature 115oC, 125oC and 135oC does not meet allthe parameters Marshall, because the value of Marshall Quotient (MQ) did not enter thespecifications of Highways in 2010 .Keywords : Solidification temperature , Specification for Highways 2010, Marshall , AsphaltConcrete - Binder Course (AC - BC)
Studi Karakteristik Marshall Pada Campuran Aspal Dengan Penambahan Limbah Botol Plastik Suhardi Suhardi; Priyo Pratomo; Hadi Ali
Jurnal Rekayasa Sipil dan Desain Vol 4, No 2 (2016): Edisi Juni 2016
Publisher : Jurnal Rekayasa Sipil dan Desain

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

This experiment aims to investigate the Marshall characteristics due to the variation addition ofPET (Polyethylene Terephthalate) at mixtures AC-BC (Asphalt Concrete-Binder Course) finelygraded with reference to the specification of Bina Marga 2010.From the result of aalysis has obtained the values of Marshall parameters, the value of the 1 stobject groups test and 2nd object groups test, for the parameters marshall meets the specificationsalready determined by the Bina Marga 2010 on the asphalt level range 6.38% up 6.5%, and theoptimum bitumen content value has been obtained is 6.44%.This research proves that with the addition of variations of PET (Polyethylene Terephthalate) in amixture of AC-BC (Asphalt Concrete-Binder Course) was affected to the Marshall characteristics,as high as the levels of addition PET (Polyethylene Terephthalate) so the value of stability willincrease but the percentage of the value of void content in the mix will be higher.Keywords: AC-BC(Asphalt Concrete-Binder Course), Marshall, PET(Polyethylene Terephthalate)
Kepadatan Campuran dengan Variasi Tumbukkan Terhadap AC-WC Gradasi Halus Yuliansyah Yuliansyah; Hadi Ali; Priyo Pratomo
Jurnal Rekayasa Sipil dan Desain Vol 3, No 2 (2015): Edisi Juni 2015
Publisher : Jurnal Rekayasa Sipil dan Desain

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

This study was conducted to determine the effect of variations in the compaction of thecharacteristics of the asphalt layer using the Marshall method which refers to the buildingspecifications of bina marga 2010. In the Marshall plan establishes parameters for the number ofcompaction of heavy traffic conditions compaction test specimen as 2x75 compaction with thecavity boundary mixture of 3,5- 5.5%. While on the asphalt concrete layer is studied AsphaltConcrete Wearing Coarse (AC-WC) subtle gradations lower limit.After the results of the testing materials testing both asphalt and aggregate meets the standardsand then do the manufacture asphalt mixture specimen. From the analysis of the value obtainedafter calculating the optimum asphalt content lower limit of 6,8%. Then used in mixing asphaltcontent for the variation of the collision is 2x50, 2x55, 2x60, 2x65, 2x70, 2x75, 2x80, and 2x85.After it was examined Marshall.From the test results on compaction Marshall 2x50, 2x55, 2x60, 2x65, and 2x70. Does not meetthe Marshall parameter value because Marshall Quotient (MQ) does not enter the specifications.While the value of voids In The Mix (VIM) in the collision 2x50, 2x55, 2x60, 2x65, and 2x70 arealso not included in the specification. Only on compaction of 2x75, 2x80 and 2x85 that meet theparameters of Marshall.Keywords : Compaction, Asphalt Concrete - Wearing Course (AC-WC) Subtle Gradation,Marshall Parameters, Bina Marga Specifications 2010.
Analisis Perencanaan Tebal Lapis Tambah (overlay) Cara Lenduntan Balik Dengan Metode Pd T-05-2005-B dan Pedoman Interim No.002/P/BM/2011 Danu Wahyudi; Priyo Pratomo; Hadi Ali
Jurnal Rekayasa Sipil dan Desain Vol 4, No 1 (2016): Edisi Maret 2016
Publisher : Jurnal Rekayasa Sipil dan Desain

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Roads are the transport infrastructures which play an important role in supporting the economicgrowth of a region. Therefore it is necessary to do maintenance efforts so that the roads canfunction optimally.One of them is by adding overlay. The selection of methods become a factorthat must be considered before doing flexible pavement overlay design. It is because of improperplanning can cause damaged or uneconomical construction of roads. Along with the technologicaladvances, methods of overlay flexible pavement design based on deflection also undergone manymodifications such as“Pedoman Perencanaan Tebal Lapis Tambah Perkerasan Lentur Pd T-05-2005-B”and “Pedoman Interim Perkerasan Jalan Lentur No.002/P/BM/201”. The purpose of thisresearch was to determine the most optimal and most efficient life cyclecost of overlay design inthe roads performance improvement project of Batas Kota Metro-Gedung Dalam. From theanalysis results show that the design results by using Pd T 05-2005-B were thinner than PedomanInterim No.002/P/BM/2011. It was caused by several factors such as the analysis of traffic,temperature correction factor, and the types of materials used. The indicator value of theinternational roughness index (IRI) is predicated by emperical equations and the design life of 20years, obtained the lowest lifecycle costs are the result of design methods Pd T-05-2005-B. Theresults of the analysis also showed that the cost at the end of the design life methods Pd T-05-2005-B less than Pedoman Interim No.002 /P/BM / 2011.Keywords :Road, Overlay, Life Cycle Cost
Co-Authors Abdurrohmansyah Abdurrohmansyah Andriansyah Andriansyah Budi Raharjo Danu Wahyudi I Wayan Diana Idharmahadi Adha Ketut Swandana Priyo Pratomo Suhardi Suhardi Tarkono Tarkono Teguh Dwi Istanto Wahyudi Wahyudi Yuliansyah Yuliansyah