Claim Missing Document
Check
Articles

Found 4 Documents
Search

PERHITUNGAN STRUKTUR JEMBATAN BETON BERTULANG SUNGAI MUARA TERSAN DI DESA JONGKANG KECAMATAN LOA KULU KABUPATEN KUTAI KARTANEGARA FAUZI, ILHAM
KURVA S JURNAL MAHASISWA Vol 1, No 2 (2013)
Publisher : KURVA S JURNAL MAHASISWA

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (594.944 KB)

Abstract

Jembatan Sungai Muara Tersan terletak didesa Jongkang Kecamatan Loa Kulu Kabupaten Kutai Kartanegara, jembatan dibuat dengan konstruksi beton bertulang yang merupakan satu kesatuan dengan lantai kendaraan. Tujuan perhitungan adalah untuk mengetahui kebutuhan dimensi dan penulangan struktur atas dan bawah jembatan. Analisa dalam perhitungan ini menggunakan SNI T-02-2005 (Standart Pembebanan Untuk Jembatan). Dari hasil perhitungan diperoleh panjang jembatan25m lebar jembatan 6m, kesimpulan dimensi dan penulangan struktur utama berupa balok gelegar adalah 150cm x 60cm dengan tulangan utama 20D32 dan tulangan geser Ø12-150, balok diafragma 30cm x 50cm dengan tulangan 2D19 dan tulangan geser D12-200, dan tebal plat lantai kendaraan 20cm dengan tulangan utama D16-150 dan tulangan bagi Ø12-150. Dimensi hasil perhitungan abutment dengan lebar 3.30m, panjang 9.00m dan tinggi 5.10m.
A PRELIMINARY RESULT OF AIR QUALITY IDENTIFICATION AND ANALYSIS OF PM10 AND PM2.5 IN STEEL INDUSTRIAL AREA, CILEGON, BANTEN Setiawati, Ira; Ermawati, Rahyani; Kang, Kitai; Chang, Insoo; Hong, Kihwan; Ervina, Ervina; Ariani, Auliyah; Fauzi, Ilham; Syah, Indra Lukman; Sefriana, Fita; Sari, Yesy Komala
Jurnal Riset Teknologi Pencegahan Pencemaran Industri Vol 10, No 1 (2019)
Publisher : Kementerian Perindustrian

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21771/jrtppi.2019.v10.no1.p22-28

Abstract

The increasingly rapid industrial development has produced pollutants in the form of gases and particles polluting the atmosphere. One of them is the steel industry where the majority of the air pollutants produced is particulate matter. Monitoring the air quality of particulate matter needs to be done routinely to identify and control the effects of air pollution somewhere. The purpose of this study is to identify and analyze particulate matter (PM10 and PM2.5) in the steel industry area in Cilegon, Indonesia. Ambient particulate matter is sampling by low-volume Sequential Particulate Matter (PM) Sampler with flow rate 5-20 L/minute for 24 hours per day in 4 months from September 2018 to January 2019. The results of identification and analysis of PM10 and PM2.5 in the steel industry area, Cilegon, Indonesia showed concentrations that varied greatly depending on sampling location conditions, with an average concentration range of 89.38 - 141.13 µg/m3 for PM10 and 21.74 - 50.69 µg/m3 for PM2.5.
A PRELIMINARY RESULT OF AIR QUALITY IDENTIFICATION AND ANALYSIS OF PM10 AND PM2.5 IN STEEL INDUSTRIAL AREA, CILEGON, BANTEN Setiawati, Ira; Ermawati, Rahyani; Kang, Kitai; Chang, Insoo; Hong, Kihwan; Ervina, Ervina; Ariani, Auliyah; Fauzi, Ilham; Syah, Indra Lukman; Sefriana, Fita; Sari, Yesy Komala
Jurnal Riset Teknologi Pencegahan Pencemaran Industri Vol 10, No 1 (2019)
Publisher : Kementerian Perindustrian

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21771/jrtppi.2019.v10.no1.p22-28

Abstract

The increasingly rapid industrial development has produced pollutants in the form of gases and particles polluting the atmosphere. One of them is the steel industry where the majority of the air pollutants produced is particulate matter. Monitoring the air quality of particulate matter needs to be done routinely to identify and control the effects of air pollution somewhere. The purpose of this study is to identify and analyze particulate matter (PM10 and PM2.5) in the steel industry area in Cilegon, Indonesia. Ambient particulate matter is sampling by low-volume Sequential Particulate Matter (PM) Sampler with flow rate 5-20 L/minute for 24 hours per day in 4 months from September 2018 to January 2019. The results of identification and analysis of PM10 and PM2.5 in the steel industry area, Cilegon, Indonesia showed concentrations that varied greatly depending on sampling location conditions, with an average concentration range of 89.38 - 141.13 µg/m3 for PM10 and 21.74 - 50.69 µg/m3 for PM2.5.
A Preliminary Result Of Air Quality Identification And Analysis Of Pm10 And Pm2.5 In Steel Industrial Area, Cilegon, Banten Setiawati, Ira; Ermawati, Rahyani; Kang, Kitai; Chang, Insoo; Hong, Kihwan; Ervina, Ervina; Ariani, Auliyah; Fauzi, Ilham; Syah, Indra Lukman; Sefriana, Fita; Sari, Yessy Komala
Jurnal Riset Teknologi Pencegahan Pencemaran Industri Vol. 10 No. 1 (2019)
Publisher : Balai Besar Standardisasi dan Pelayanan Jasa Pencegahan Pencemaran Industri

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21771/jrtppi.2019.v10.no1.p22-28

Abstract

The increasingly rapid industrial development has produced pollutants in the form of gases and particles polluting the atmosphere. One of them is the steel industry where the majority of the air pollutants produced is particulate matter. Monitoring the air quality of particulate matter needs to be done routinely to identify and control the effects of air pollution somewhere. The purpose of this study is to identify and analyze particulate matter (PM10 and PM2.5) in the steel industry area in Cilegon, Indonesia. Ambient particulate matter is sampling by low-volume Sequential Particulate Matter (PM) Sampler with flow rate 5-20 L/minute for 24 hours per day in 4 months from September 2018 to January 2019. The results of identification and analysis of PM10 and PM2.5 in the steel industry area, Cilegon, Indonesia showed concentrations that varied greatly depending on sampling location conditions, with an average concentration range of 89.38 - 141.13 µg/m3 for PM10 and 21.74 - 50.69 µg/m3 for PM2.5.