cover
Article Per Year (5 Year)
All
Home Page
OAI Link
Editorial Team
Contact
Reviewer
Google Scholar
Contact Name
Istadi
Contact Email
istadi@che.undip.ac.id
Phone
+6281316426342
Journal Mail Official
bcrec@live.undip.ac.id
Editorial Address
Editorial Office of Bulletin of Chemical Reaction Engineering & Catalysis Laboratory of Plasma-Catalysis (R3.5), UPT Laboratorium Terpadu, Universitas Diponegoro Jl. Prof. Soedarto, Semarang, Central Java, Indonesia 50275
Location
Kota semarang,
Jawa tengah
INDONESIA
Bulletin of Chemical Reaction Engineering & Catalysis
Published by Masyarakat Katalis Indonesia - Indonesian Catalyst Society
ISSN : -     EISSN : 19782993     DOI : https://doi.org/10.9767/bcrec
Core Subject : Science, Engineering,
Chemical Engineering, Chemistry & Bioengineering Chemistry
Bulletin of Chemical Reaction Engineering & Catalysis, a reputable international journal, provides a forum for publishing the novel technologies related to the catalyst, catalysis, chemical reactor, kinetics, and chemical reaction engineering. Scientific articles dealing with the following topics in chemical reaction engineering, catalysis science, and engineering, catalyst preparation method and characterization, novel innovation of chemical reactor, kinetic studies, etc. are particularly welcome. However, articles concerned on the general chemical engineering process are not covered and out of the scope of this journal. This journal encompasses Original Research Articles, Review Articles (only selected/invited authors), and Short Communications, including: fundamentals of catalyst and catalysis; materials and nano-materials for catalyst; chemistry of catalyst and catalysis; surface chemistry of catalyst; applied catalysis; applied bio-catalysis; applied chemical reaction engineering; catalyst regeneration; catalyst deactivation; photocatalyst and photocatalysis; electrocatalysis for fuel cell application; applied bio-reactor; membrane bioreactor; fundamentals of chemical reaction engineering; kinetics studies of chemical reaction engineering; chemical reactor design (not process parameter optimization); enzymatic catalytic reaction (not process parameter optimization); kinetic studies of enzymatic reaction (not process parameter optimization); the industrial practice of catalyst; the industrial practice of chemical reactor engineering; application of plasma technology in catalysis and chemical reactor; and advanced technology for chemical reactors design. However, articles concerned about the "General Chemical Engineering Process" are not covered and out of the scope of this journal.
Arjuna Subject : Teknik Kimia (semua kategori) - Katalisis
Articles 20 Documents
 1   2 
Search results for , issue "2021: BCREC Volume 16 Issue 1 Year 2021 (March 2021)" : 20 Documents clear
Physical-chemical Characterization of Nano-Zinc Oxide/Activated Carbon Composite for Phenol Removal from Aqueous Solution Allwar Allwar; Asih Setyani; Ulul Sugesti; Khusna Afifah Fauzani
Bulletin of Chemical Reaction Engineering & Catalysis 2021: BCREC Volume 16 Issue 1 Year 2021 (March 2021)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.16.1.10282.136-147

Abstract

Oil palm shell was used as a precursor for preparation of activated carbon using different chemical activations (potassium hydroxide (KOH), zinc chloride (ZNCl2), and phosphoric acid (H3PO4)). Each activated carbons (AC) was mixed with nano-zinc oxide to form a composite. From the gas sorption analyzer, it is showed that nitrogen adsorption isotherms show Type II for ZnO/AC-KOH and ZnO/AC-ZnCl2 corresponding to the micro- and mesoporous structures, respectively. However, the nitrogen adsorption isotherm of ZnO/AC-H3PO4 exhibits the Type I with predominantly microporous structures. The SEM micrographs produced unsmooth surface and different pore sizes. The XRD patterns at 2θ of 25.06° and 26.75° were come from amorphous activated carbon. The peak intensity of ZnO was weak due to low concentration of zinc precursor. However, the ZnO of ZnO/AC-ZnCl2 showed strongly peak intensity. The effectiveness of the composites was examined for phenol removal determined by UV-Vis Spectrophotometer method. The equilibrium adsorption follows the Langmuir and Freundlich models according to the best correlation coefficient (R2). The kinetic model was only obtained for the pseudo-second-order with the best linearity of the correlation coefficient (R2). The results of this study showed that the oil palm shell has a great potential for ZnO/AC with excellent adsorptive property. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 
Nickel-phenanthroline Complex Supported on Mesoporous Carbon as a Catalyst for Carboxylation under CO2 Atmosphere Iman Abdullah; Riri Andriyanti; Dita Arifa Nurani; Yuni Krisyuningsih Krisnandi
Bulletin of Chemical Reaction Engineering & Catalysis 2021: BCREC Volume 16 Issue 1 Year 2021 (March 2021)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.16.1.9733.111-119

Abstract

Carbon dioxide is a highly potential renewable C1 source for synthesis of fine chemicals. Utilization of CO2 in carboxylation reactions requires catalysts, such as: nickel complex for CO2 activation. However, the use of homogeneous catalysts in the reaction is still less efficient due to the difficulty of separating the product and catalyst from reaction mixture. Therefore, it is necessary to heterogenize the nickel complex in a solid support such as mesoporous carbon. In this report, mesoporous carbon (MC) prepared from phloroglucinol and formaldehyde through soft template method was used as a solid support for Ni-phenanthroline complex (Ni-phen). The catalyst was characterized by Fourier Transform Infra Red (FT-IR), X-Ray Diffraction (XRD), Scanning Electron Microscope - Energy Dispersive X-Ray (SEM-EDX), and Surface Area Analyzer (SAA). The result of SAA characterization showed that the pore diameter of MC was 6.7 nm and Ni-phen/MC was 5.1 nm which indicates that the materials have meso-size pores. Ni-phen/MC material was then used as a heterogeneous catalyst in the carboxylation reaction of phenylacetylene under an ambient CO2 pressure. The reactions were carried out in several variations of conditions such as temperature, time and catalyst types. Based on the results of the reaction, the best conditions were obtained at 25 °C for 8 h of reaction time using Ni-phen/MC catalyst.  Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 
Study on Ammonia-induced Catalyst Poisoning in the Synthesis of Dimethyl Oxalate Hua-wei Liu; Sheng-tao Qian; Er-fei Xiao; Ying-jie Liu; Jun Lei; Xian-hou Wang; Yu-hua Kong
Bulletin of Chemical Reaction Engineering & Catalysis 2021: BCREC Volume 16 Issue 1 Year 2021 (March 2021)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.16.1.9572.1-8

Abstract

On an industrial plant, we observed and examined the ammonia-poisoning catalyst for the synthesis of dimethyl oxalate (DMO). We investigated the catalytic activity in response to the amount of ammonia and revealed the mechanism of such poisoning by X-ray photoelectron spectroscopy (XPS) characterization. Our results show that only 0.002% ammonia in the feed gas can significantly deactivate the Pd-based catalyst. Two main reasons were proposed: one is that the competitive adsorption of ammonia on the active component Pd hinders the carbon    monoxide (CO) coupling reaction and the redox cycle between Pd0 and Pd2+; and the other is that the high-boiling nitrogen-containing amine compounds formed by reacting with ammonia have adsorbed on the catalyst, which hinders the progress of the catalytic reaction. The deactivation caused by the latter is irreversible. The catalytic activity can be completely restored by a low-temperature liquid-phase in-situ regeneration treatment. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 
A Two-Step SO3H/ICG Catalyst Synthesis for Biodiesel Production: Optimization of Sulfonation Step via Microwave Irradiation Nur Nazlina Saimon; Norzita Ngadi; Mazura Jusoh; Zaki Yamani Zakaria
Bulletin of Chemical Reaction Engineering & Catalysis 2021: BCREC Volume 16 Issue 1 Year 2021 (March 2021)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.16.1.9613.63-75

Abstract

Conventional heating, a common method used for heterogeneous solid acid catalyst synthesis unknowingly consumes massive time and energy. In this study, acid catalyst was prepared through sulfonation process of incomplete carbonized glucose (ICG) via microwave-assisted technique to shorten the heating time and energy consumption. Optimization of the sulfonation process of ICG via microwave-assisted was carried out. Four-factor-three-level central composite design (CCD) was used to develop the design of experiments (DOE). Interaction between two factors was evaluated to determine the optimum process conditions. A quadratic model was proposed for prediction of biodiesel yield (Y) from palm fatty acid distillate (PFAD) and its conversion (C). The application of DOE successfully optimized the operating conditions for the two-step SO3H/ICG catalyst synthesis to be used for the esterification process. The optimized conditions of the best performing SO3H/ICG with maximum Y and C were at 7.5 minutes of reaction time, 159.5 mL of H2SO4 used, 671 rpm of stirring rate as well as 413.64 watt of power level. At these optimum conditions the predicted yield percentage and conversion percentage were 94.01% and 91.89%, respectively, which experimentally verified the accuracy of the model. The utilization of sulfonated glucose solid acid catalyst via microwave-assisted in biodiesel production has great potential towards sustainable and green method of synthesizing catalyst for biodiesel. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 
Effect of Calcination Temperature on the Photocatalytic Activity of Zn2Ti3O8 Materials for Phenol Photodegradation Krisfian Tata Aneka Priyangga; Yehezkiel Steven Kurniawan; Leny Yuliati
Bulletin of Chemical Reaction Engineering & Catalysis 2021: BCREC Volume 16 Issue 1 Year 2021 (March 2021)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.16.1.10322.196-204

Abstract

Zinc titanate (Zn2Ti3O8) is a bimetal oxide material that is especially attractive as a photocatalyst. In the preparation of the Zn2Ti3O8, the calcination temperature is a crucial parameter. Hence, in the present work, we aimed to synthesize the Zn2Ti3O8 materials from zinc(II) nitrate and titanium(IV) isopropoxide as precursors by using a sol-gel method and followed by calcination at 700, 900, and 1100 °C to give ZT-700, ZT-900, and ZT-100 materials, respectively. The ZT materials were characterized using Fourier transform infrared (FTIR), diffuse reflectance ultraviolet-visible (DR UV-vis), and fluorescence spectroscopies. It was confirmed that the ZT materials contained O−Ti−O, Zn−O−Ti, Zn−O, Ti−O−Ti, and Ti−O functional groups as shown from their FTIR spectra. Similar fluorescence properties were only observed on the ZT-700 and ZT-900. From the bandgap energy analysis, ZT-700 and ZT-900 contained spinel and cubic Zn2Ti3O8 (spl-Zn2Ti3O8 and c-Zn2Ti3O8) crystal phases), while ZT-1100 contained c-Zn2TiO4 and TiO2 rutile crystal phases. The kinetic analysis of photocatalytic phenol degradation showed that both ZT-700 and ZT-900 materials exhibited high photocatalytic activity with the reaction rate constants of 0.0353 and 0.0355 h−1, respectively. These values were higher than that of the ZT-1100 (0.0206 h−1). This study demonstrated that calcination at 700 and 900 °C resulted in the formation of the spl-Zn2Ti3O8 and c-Zn2Ti3O8 phases, which were effective as the photocatalyst, but the formation of c-Zn2TiO4 and rutile TiO2 at calcination of 1100 °C deteriorated the photocatalytic activity. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 
Backmatter (Publication Ethics, Copyright Transfer Agreement for Publishing Form)
Bulletin of Chemical Reaction Engineering & Catalysis 2021: BCREC Volume 16 Issue 1 Year 2021 (March 2021)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.16.1.10723.App.1-App.5

Abstract

Investigation of Chlorophyl-a Derived Compounds as Photosensitizer for Photodynamic Inactivation Listiana Oktavia; Irma Mulyani; Veinardi Suendo
Bulletin of Chemical Reaction Engineering & Catalysis 2021: BCREC Volume 16 Issue 1 Year 2021 (March 2021)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.16.1.10314.161-169

Abstract

Chlorophyll has unique physicochemical properties which makes them good as photosensitizer of Photodynamic Inactivation (PDI). The physicochemical properties of chlorophyll as photosensitizer can be optimized through several routes.  One of the possible route is by replacing the metal ion center of chlorophyll with other ions. In this research, the effect of coordinated metal ion in the natural chlorophyll-a was studied for bacterial growth (S. aureus) inhibition. The replacement of metal in the center of chlorophyll hopefully can improve the intensity of Intersystem Crossing Mechanism (ISC) lead to the formation of singlet oxygen species. The chlorophyll a and b were isolated from spinach via precipitation technique using 1,4 dioxane and water. The chlorophyll a and b were separated using sucrose column chromatography. The thin layer chromatography result showed that chlorophyll a (Rf: 0.57) had been well separated with chlorophyll b (Rf: 0.408). The absorption spectra of chlorophyll a and b showed that the Soret band was observed at 411 and 425 nm, while the Q band appeared at 663 and 659 nm. Replacement of metal ion center shifted the Soret band of chlorophyll- a derivatives to lower energy region, while Q-band was slightly shifted to the higher energy region. The absorption and the fluorescence intensity were  also observed decreasing after ion replacement. The Inhibition activity investigation over S. aureus showed the highest inhibition activity was exhibited by Zn-pheophytin-a (66.8%) followed by chlorophyll a (30.1 %) and Cu-pheophytin-a (0%). The inhibition activity is correlated with decreasing fluorescence intensity. The formation of singlet oxygen by ISC mechanism is hypothesized to deactivate the excitation state of Cu-pheophytin-a. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 
Kinetic Studies of the Glycerolysis of Urea to Glycerol Carbonate in the Presence of Amberlyst-15 as Catalyst Hary Sulistyo; Wahyudi Budi Sediawan; Reviana Inda Dwi Suyatno; Indah Hartati
Bulletin of Chemical Reaction Engineering & Catalysis 2021: BCREC Volume 16 Issue 1 Year 2021 (March 2021)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.16.1.8893.52-62

Abstract

Amberlyst-15, a strong acidic ion-exchange resin, has showed as a potential and an effective catalyst for the glycerolysis process of urea to glycerol carbonate. In this work, the kinetic model of the urea glycerolysis over Amberlyst-15 catalyst was investigated. The kinetic model was developed by considering simultaneous steps of urea dissolution in glycerol, mass transfer of urea and glycerol from the bulk of the liquid into the outer part of the catalyst, diffusion of urea and glycerol into the inner part of the particle through the catalyst pores, and irreversible second order reaction of urea and glycerol on the active sites. The irreversibility of second order reaction of urea glycerolysis was validated and proven. The proposed kinetic model was simulated and validated with the experimental data. The kinetic studies show that mechanism proposed works well. Furthermore, the activation energy was found to be 145.58 kJ.mol−1 and the collision factor was in 8.00×1010 (m3)2.kg−1.mol−1.s−1. The simulation result shows that the predicted liquid temperatures were close to the experimental temperature data. It also gave glycerol concentration profile inside the catalyst particle as a function of glycerolysis time and position. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 
Modification of Mordenite Characters by H2C2O4 and/or NaOH Treatments and Its Catalytic Activity Test in Hydrotreating of Pyrolyzed α-Cellulose Triyono Triyono; Wega Trisunaryanti; Yessi Wydia Putri; Dyah Ayu Fatmawati; Uswatul Chasanah
Bulletin of Chemical Reaction Engineering & Catalysis 2021: BCREC Volume 16 Issue 1 Year 2021 (March 2021)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.16.1.9476.9-21

Abstract

The research about modification of mordenite characteristics has been performed by H2C2O4 and/or NaOH treatments and catalytic activity tests in hydrotreating of pyrolyzed a-cellulose. Commercial mordenite (HSZ-604OA) as mordenite control (HM) immersed in 0.05, 0.5, and 1.0 M H2C2O4 at 70 °C for three hours resulting in HM-0.05, HM-0.5, and HM-1. The four mordenites were immersed in 0.1 M NaOH for 15 minutes resulting in BHM, BHM-0.05, BHM-0.5, and BHM-1. The catalysts obtained were analyzed by XRD, SAA, ICP, and acidity test. The catalytic activity of the mordenites was evaluated in hydrotreating of pyrolyzed a-cellulose using stainless steel reactor with an H2 gas flow rate of 20 mL.min−1 at 450 °C for two hours with a catalyst: feed weight ratio of 1:60. The liquid products obtained from the hydrotreating were analyzed using GC-MS. The research results showed that the H2C2O4 and/or NaOH treatment towards the mordenites increased Si/Al ratio and decreased crystallinity. The acidity of mordenites decreased along with the increase of the Si/Al ratio. The average pore diameter of BHM, BHM-0.05, BHM-0.5, and BHM-1 mordenites were 2.898; 3.005; 3.792; 7.429 nm, respectively. The BHM-0.5 mordenite showed the highest catalytic activity in generating liquid product (88.88 wt%) and selectivity toward propanol (4.87 wt%). The BHM-1 mordenite showed catalytic activity in generating liquid product (41.16 wt%) and selectivity toward ethanol (1.21 wt%) and 2-heptyne (4.36 wt%). Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 
Light-Harvesting Metal-Organic Frameworks (MOFs) La-PTC for Photocatalytic Dyes Degradation Agustino Zulys; Adawiah Adawiah; Jarnuzi Gunlazuardi; Muhammad Derry Luthfi Yudhi
Bulletin of Chemical Reaction Engineering & Catalysis 2021: BCREC Volume 16 Issue 1 Year 2021 (March 2021)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.16.1.10309.170-178

Abstract

A novel porous metal organic framework, La-PTC was synthesized by solvothermal method using a perylene-3,4,9,10-tetracarboxylate ligand and lanthanum metal ion. The FTIR analysis showed that La-PTC has a different structure with PTCDA and Na4PTC. The La-PTC MOF has high crystallinity, bandgap energy of 2.21 eV with a maximum absorption area at 561 nm. A rod shape structure of La-PTC has been obtained with the surface area of 22.2364 m2.g−1 and classified into mesoporous material. The La-PTC was relative stable up to 376.93 °C. The La-PTC can degrade 64.76% of MO within ca. 240 min under visible light irradiation with the amount of 30 mg La-PTC. The addition of H2O2 improved the photocatalytic activity of La-PTC with degradation efficiency of 67.02%, 70.00%, and 99.60% for MB, RhB, and MO, respectively. This study presents the fabrication of the light-harvesting metal organic framework, La-PTC and its potential in dyes degradation. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 

Page 1 of 2 | Total Record : 20

 1   2 

Filter by Year

2021 2021


Reset
Filter By Issues
All Issue 2024: BCREC Volume 19 Issue 1 Year 2024 (April 2024) 2024: Just Accepted Manuscript and Article In Press 2024 2023: BCREC Volume 18 Issue 4 Year 2023 (December 2023) 2023: BCREC Volume 18 Issue 3 Year 2023 (October 2023) 2023: BCREC Volume 18 Issue 2 Year 2023 (August 2023) 2023: BCREC Volume 18 Issue 1 Year 2023 (April 2023) 2022: BCREC Volume 17 Issue 4 Year 2022 (December 2022) 2022: BCREC Volume 17 Issue 3 Year 2022 (September 2022) 2022: BCREC Volume 17 Issue 2 Year 2022 (June 2022) 2022: BCREC Volume 17 Issue 1 Year 2022 (March 2022) 2021: BCREC Volume 16 Issue 4 Year 2021 (December 2021) 2021: BCREC Volume 16 Issue 3 Year 2021 (September 2021) 2021: BCREC Volume 16 Issue 2 Year 2021 (June 2021) 2021: BCREC Volume 16 Issue 1 Year 2021 (March 2021) 2020: BCREC Volume 15 Issue 3 Year 2020 (December 2020) 2020: BCREC Volume 15 Issue 2 Year 2020 (August 2020) 2020: BCREC Volume 15 Issue 1 Year 2020 (April 2020) 2019: BCREC Volume 14 Issue 3 Year 2019 (December 2019) 2019: BCREC Volume 14 Issue 2 Year 2019 (August 2019) 2019: BCREC Volume 14 Issue 1 Year 2019 (April 2019) 2018: BCREC Volume 13 Issue 3 Year 2018 (December 2018) 2018: BCREC Volume 13 Issue 2 Year 2018 (August 2018) 2018: BCREC Volume 13 Issue 1 Year 2018 (April 2018) 2017: BCREC Volume 12 Issue 3 Year 2017 (December 2017) 2017: BCREC Volume 12 Issue 2 Year 2017 (August 2017) 2017: BCREC Volume 12 Issue 1 Year 2017 (April 2017) 2016: BCREC Volume 11 Issue 3 Year 2016 (December 2016) 2016: BCREC Volume 11 Issue 2 Year 2016 (August 2016) 2016: BCREC Volume 11 Issue 1 Year 2016 (April 2016) 2015: BCREC Volume 10 Issue 3 Year 2015 (December 2015) 2015: BCREC Volume 10 Issue 2 Year 2015 (August 2015) 2015: BCREC Volume 10 Issue 1 Year 2015 (April 2015) 2014: BCREC Volume 9 Issue 3 Year 2014 (December 2014) 2014: BCREC Volume 9 Issue 2 Year 2014 (August 2014) 2014: BCREC Volume 9 Issue 1 Year 2014 (April 2014) 2013: BCREC Volume 8 Issue 2 Year 2013 (December 2013) 2013: BCREC Volume 8 Issue 1 Year 2013 (June 2013) 2013: BCREC Volume 7 Issue 3 Year 2013 (March 2013) 2012: BCREC Volume 7 Issue 2 Year 2012 (December 2012) 2012: BCREC Volume 7 Issue 1 Year 2012 (June 2012) 2011: BCREC Volume 6 Issue 2 Year 2011 (December 2011) 2011: BCREC Volume 6 Issue 1 Year 2011 (June 2011) 2010: BCREC Volume 5 Issue 2 Year 2010 (December 2010) 2010: BCREC Volume 5 Issue 1 Year 2010 (June 2010) 2009: BCREC Volume 4 Issue 2 Year 2009 (December 2009) 2009: BCREC Volume 4 Issue 1 Year 2009 (June 2009) 2008: BCREC Volume 3 Issue 1-3 Year 2008 (December 2008) 2007: BCREC: Volume 2 Issues 2-3 Year 2007 (October 2007) 2007: BCREC: Volume 2 Issue 1 Year 2007 (June 2007) More Issue