Article Per Year (5 Year)
p-Index From 2019 - 2024
2.87
P-Index
This Author published in this journals
All Journal Jurnal Teknologi Elektro JTT (Jurnal Teknologi Terpadu) JURNAL INTEGRASI INOVTEK POLBENG Abdimas Galuh : Jurnal Pengabdian Kepada Masyarakat Jurnal INOVTEKSeri Elektro JAREE (Journal on Advanced Research in Electrical Engineering) Jurnal Pengabdian kepada Masyarakat Jurnal Nasional Teknik Elektro dan Teknologi Informasi POLIGRID Power Elektronik : Jurnal Orang Elektro
Syechu Dwitya Nugraha
Departemen Teknik Elektro, Politeknik Elektronika Negeri Surabaya
Agriculture, Biological Sciences & Forestry Humanities Civil Engineering, Building, Construction & Architecture Computer Science & IT Control & Systems Engineering Economics, Econometrics & Finance Electrical & Electronics Engineering Energy Engineering Environmental Science Languange, Linguistic, Communication & Media Law, Crime, Criminology & Criminal Justice Materials Science & Nanotechnology Mechanical Engineering Nursing Public Health Social Sciences Other

Published : 17 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 2 Documents
Search
Journal : Jurnal Nasional Teknik Elektro dan Teknologi Informasi

 1 
Desain dan Simulasi Bidirectional DC-DC Converter untuk Penyimpanan Energi pada Sistem Fotovoltaik Armadilla Sukma Pratiwi; Syechu Dwitya Nugraha; Epyk Sunarno
Jurnal Nasional Teknik Elektro dan Teknologi Informasi Vol 9 No 3: Agustus 2020
Publisher : Departemen Teknik Elektro dan Teknologi Informasi, Fakultas Teknik, Universitas Gadjah Mada

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1376.624 KB) | DOI: 10.22146/.v9i3.377

Abstract

In this paper, a bidirectional DC-DC converter for energy storage in the photovoltaic system has been designed and simulated on MATLAB Simulink. The bidirectional DC-DC converter can work in two modes, charge and discharge mode. The energy storage system will work to store energy into the battery when the power generation capacity is higher than load demand. Then, the energy stored in the battery will be used for the DC bus supply when the power generation capacity is lower than the load demand. To get a constant voltage on the high voltage side (DC bus voltage) and a constant current on the low voltage side (charging current), a PI controller is used. Simulations were carried out with 1,000 W/m2 irradiation to get the power generation higher than the load demand (charge mode) and 200 W/m2 irradiation to get the power generation lower than the load demand (discharge mode) with constant temperature of 25 °C. The test result shows that a bidirectional DC-DC converter can work in charge and discharge modes, which is shown by battery charging currents and the increase or decrease in battery voltage.
Desain dan Simulasi Dual Input Single Output Buck Converter dengan Kontrol Fuzzy Abdul Rahman Wachid; Endro Wahjono; Syechu Dwitya Nugraha Nugraha
Jurnal Nasional Teknik Elektro dan Teknologi Informasi Vol 10 No 1: Februari 2021
Publisher : Departemen Teknik Elektro dan Teknologi Informasi, Fakultas Teknik, Universitas Gadjah Mada

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1969.491 KB) | DOI: 10.22146/jnteti.v10i1.1069

Abstract

In this paper, a dual input single output buck converter with fuzzy control is designed and simulated for a DC load supply using the PSIM software. The dual input single output buck converter can work with two different sources. The use of the two power sources of photovoltaic and wind turbine is an alternative solution for obtaining a greater rated power to supply DC loads. The solar panel and the wind turbine will supply the power for the dual input buck converter circuit simultaneously. For the two power sources to work simultaneously, the duty cycle is set using fuzzy control, so that the output voltage can match the desired voltage. Simulation testing is carried out with photovoltaic conditions with varying irradiation and temperature values, as well as varying wind speeds in the wind turbine, i.e, between 4-8 m/s. The simulation results show that the dual-input single-output buck converter can work when powered by two different power sources with a stable output voltage of the converter at its set point, i.e., 14.4 volts.
Co-Authors ABDILLAH AZIZ MUNTASHIR Abdul Rahman Wachid Ahmad Firyal Adila Armadilla Sukma Pratiwi Arman Jaya Diah Septi Yanaratri Dimas Okky Eka Prasetyono, Eka Endro Wahjono Epyk Sunarno Era Purwanto Farid Dwi Murdianto Ferdiansyah, Indra Gigih Prabowo Habibi Mushthofa Husnu Zain Hendik Eko Hadi Suharyanto Imam Dui Agusalim Indra Ferdiansyah Intan Sholikha Irianto Irianto Lucky Pradigta Lucky Pradigta Setiya Raharja M Chaninul Fuad Mochammad Berliano Putra Ramadhan Moh. Ifaldi Akbar Moh. Zaenal Efendi Mohammad Zaenal Efendi Muhammad Irfan Zaidan Muhammad Rizani Rusli Novie Ayub Windarko Nuva Choironi Ersha Qudsi, Ony Asrarul Rachma Prilian Eviningsih Renny Rakhmawati Rifqi Dary Suryanto Suryono Suryono Sutedjo Sutedjo Zahro Zachari