Claim Missing Document
Check
Articles

Found 15 Documents
Search

DESAIN LOW NOISE TRANSCEIVER 7 MHZ BERBASIS SOFTWARE DEFINED RADIO (SDR) Sotyohadi Sotyohadi; Irrine Budi Sulistiawati
Mnemonic : Jurnal Teknik Informatika Vol 2 No 1 (2019): Mnemonic Vol. 2 No. 1
Publisher : Teknik Informatika, Institut Teknologi Nasional malang

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1463.014 KB) | DOI: 10.36040/mnemonic.v2i1.55

Abstract

Software defined radio (SDR) adalah paradigma baru dalam desain perangkat komunikasi wireless. Teknologi SDR saat ini digunakan secara luas pada bidang telekomunikasi komersil seperti satelit komunikasi, telepon bergerak dan banyak digunakan pada kalangan komunitas radio amatir. SDR adalah suatu sistem radio dimana komponen-komponennya yang biasanya di bangun oleh perangkat keras (mixer, filter, modulator, demodulator dll) digantikan fungsinya oleh perangkat lunak. Software defined radio saat ini sangat dikenal dikalangan komunitas radio amatir di seluruh dunia. Berbagai desain transceiver berbasis SDR yang bekerja pada band high frequency (HF) telah banyak diaplikasikan, dan berbagai perangkat lunak aplikasi SDR telah dikembangkan. Perangkat transceiver berbasis SDR digemari oleh komunitas radio amatir dikarenakan rangkaian elektroniknya yang sederhana. Namun dari kelebihan tersebut muncul permasalahan yang sering dijumpai adalah noise pada penerima yang tinggi dan sensitivitas rendah. Dengan latar belakang permasalahan tersebut, maka pada penelitian ini dirancanglah suatu low noise transceiver 7 MHz berbasis software defined radio (SDR). Metode yang digunakan dalam mengurangi noise adalah dengan pemisahan grounding dari rangkaian digital, analog dan penguat RF serta pemilihan chip Tayloe detector yang memiliki nilai resistansi switch yang rendah yaitu 4 ohm. Berdasarkan hasil pengujian dengan menggunakan integrated circuit (IC) yang memiliki nilai resistansi switching yang rendah 4 ohm didapatkan kinerja transceiver yang lebih baik, dimana penerimaan lebih sensitive dan memiliki noise yang lebih rendah.
Analisis Dinamis dan Statis Pada Sistem Tenaga Listrik Sumbawa Akibat Penambahan Static Var Compensator Kapasitas 4 Mvar Aldi Rahmansyah Rahmansyah; Awan Uji Krismanto; Irrine Budi Sulistiawati
Journal of Applied Smart Electrical Network and Systems Vol 3 No 01 (2022): Vol 3 No 1 : June 2022
Publisher : Indonesian Society of Applied Science (ISAS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.52158/jasens.v3i01.333

Abstract

Kestabilan tegangan mengacu pada kemampuan sistem tenaga dalam mempertahankan tegangannya untuk stabil di semua bus dalam sistem setelah mengalami gangguan. Ketika gangguan pada sistem meningkatkan permintaan dari daya reaktif di luar kapasitas sumber yang tersedia maka kestabilan tegangan terancam, skenario terburuknya adalah tegangan turun dibawah level tegangan yang ditentukan. Salah satu perangkat modern yang dapat mengkompensasi konsumsi daya reaktif pada sistem dan mampu menjaga tegangan bus pada tingkat yang diinginkan adalah SVC. Studi kasus dalam penelitian ini yaitu pada Kelistrikan Sumbawa di Gardu Induk Alas 20 kV, Sistem Kelistrikan Sumbawa ini dimodelkan menggunakan perangkat lunak DIgSILENT PowerFactory. Penelitian ini bertujuan untuk menyelidiki pengaruh sebelum dan sesudah pemasangan SVC di Gardu Indu Alas 20 kV terhadap gangguan di Bus Gardu Induk Alas sisi 70 kV. Analisis kestabilan tegangan menggunakan metode kurva P-V, dan respon tegangan sistem studi dinamik sebelum dan sesudah pemasangan SVC. Hasil simulasi menunjukkan bahwa dengan menggunakan SVC (-4Mvar), profil tegangan telah ditingkatkan. Diamati bahwa profil tegangan bus GI Alas 20 kV ditemukan 0,81 p.u tanpa SVC dan dengan SVC meningkat menjadi 0,98 p.u. Margin kestabilan tegangan juga telah ditingkatkan, didapatkan Bus GI Alas tanpa SVC stabil dipembebanan 7,22 MW dan dengan SVC stabil dipembebanan 17,83 MW sebelum terjadi Undervoltage.
Evaluasi Penambahan Pembangkit Baru 0,5 MWp Terhadap Profil Tegangan Pada Sistem Distribusi Singosari Ahmad Iqbal Zajuli; Irrine Budi Sulistiawati; Awan Uji Krismanto
Jurnal JEETech Vol. 3 No. 1 (2022): Jurnal JEETech
Publisher : Universitas Darul Ulum

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.48056/jeetech.v3i1.190

Abstract

The development of renewable energy in Indonesia has grown quite rapidly, one of which is PLTS. With this new power plant, it is hoped that the excessive use of fossil fuels will be reduced. in 2021 there a new PLTS operating in one of the universities, i.e at the Malang National Institute of Technology with a capacity of 0.5 MWp. The PLTS works on-grid into the Singosari distribution system through the Karangploso feeder so that the addition of a new generator of 0.5 MWp can cause changes in the voltage profile. the voltage profile itself is the voltage condition to be at the nominal voltage either when there is a change in load conditions or when power losses occur in the line with a standard allowable voltage profile of 0.95>V> 1.05 pu. The study used in this research is a power flow study with the Newton-Raphson method. This method is used to calculate the voltage profile on each bus of the power system either during the base case condition or when the system is integrated with PLTS 0.5 MWp. so that with the addition of a new power plant with a capacity of 0.5 MWp, it is necessary to evaluate the addition of a new generator with a capacity of 0.5 MWp to the voltage profile in the Singosari distribution system through the Karangploso feeder.
Perancangan Prototype Zelio Smart Relay pada Modifikasi PLTS On Grid untuk Kontinuitas Suplai Daya di Kampus II ITN Malang IRRINE BUDI SULISTIAWATI; WIDODO PUDJI MULYANTO; RIRIN KATARINA MATURBONG; SUGENG PRIYANTO
Jurnal Elkomika Vol 12, No 1 (2024): ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektr
Publisher : Institut Teknologi Nasional, Bandung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26760/elkomika.v12i1.50

Abstract

ABSTRAKPenggunaan PV (Photovoltaics) sebagai Pembangkit Listrik Tenaga Surya (PLTS) banyak digunakan di Indonesia. Mode pengoperasian PLTS dikenal dengan on grid dan off grid dimana PLTS on grid adalah kondisi dimana sistem selalu terhubung dengan jaringan PLN, sedangkan PLTS off grid kondisi dimana sistem mampu beroperasi sendiri ketika jaringan PLN terputus. Penelitian ini melakukan pembuatan prototype dengan cara menambahkan smart relay Zelio sebagai perangkat utamanya, dan dengan menambahkan relay sebagai pengganti Motorized Molded Case Circuit Breaker (MCCB) hasil simulasi membuktikan grid tetap dalam kondisi bertegangan setelah 20 detik dari terputusnya suplai PLN. Kata kunci: motorized mccb, plc, pembangkit listrik tenaga surya ABSTRACTThe use of PV (Photovoltaics) as a Solar Power Plant (PLTS) is widely used in Indonesia. PLTS operating modes are known as on grid and off grid, where PLTS on grid is a condition where the system is always connected to the PLN network, while PLTS off grid is a condition where the system is able to operate itself when the PLN network is disconnected. This research made a prototype by adding a smart relay Zelio as the main device, and by adding a relay as a replacement for the Motorized Molded Case Circuit Breaker (MCCB), the simulation results proved that the grid fulfilled voltage after 20 seconds of the PLN supply disconnected.Keywords: motorized mccb, plc, solar power plant
Pembuatan Prototype Pendeteksi Suhu dan Disinfektan Otomatis Pada Laboratorium Sotyohadi Sotyohadi; Irmalia Suryani F; Irrine Budi Sulistiawati; Yoppy Aldya
Jurnal JEETech Vol. 5 No. 1 (2024): Jurnal JEETech
Publisher : Universitas Darul Ulum

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.32492/jeetech.v5i1.5103

Abstract

When the pandemic occurred in 2019, disinfectant sprayers were needed for prevention, measuring body temperature at the entrance. The pandemic has been end, we still have to do this to prevent and be disciplined in healthy living. The research here will create a prototype of an automatic temperature detection and disinfectant device at the laboratory door. The laboratory location was chosen because mobility in the laboratory was conducive, if a trial was carried out it would not disturb the activity on laboratory. This spraying tool designed includes an HC-SR04 sensor for detecting the height of disinfectant liquid, a TCRT 5000 sensor for detecting a person's forehead which will take temperature measurements to the MLX90614 sensor. The buzzer sounds when the MLX90614 sensor detects a temperature above 370C. Spraying disinfectant liquid uses 2 0.2mm spayer nozzles, and a proximity sensor when detecting people passing by the spray booth.