Garuda - Garba Rujukan Digital

Article Per Year (5 Year)

All

Jurnal Ilmu dan Teknologi Kayu Tropis

JITKT
Website

Published by Masyarakat Peneliti Kayu Indonesia

ISSN : - EISSN : 16933834 DOI : -

Core Subject : Agriculture,

Agriculture, Biological Sciences & Forestry

Jurnal ini mempublikasikan artikel asli baik penelitian dasar maupun terapan di bidang ilmu pengetahuan dan teknologi kayu, bahan berlignoselulosa bukan kayu, hasil hutan lainnya dan industri hasil hutan.

Arjuna Subject : -

Articles 18 Documents

1 2

Search results for , issue "Vol 16, No 2 (2018): Jurnal Ilmu dan Teknologi Kayu Tropis" : 18 Documents clear

Pengaruh Durasi Steam terhadap Kualitas Arang Aktif Limbah Sagu (The Effect of Steam Duration on Quality and Characteristics of Activated Charcoal of Sago Waste) Siruru, Herman; Syafii, Wasrin; Wistara, Nyoman J; Pari, Gustan
Jurnal Ilmu dan Teknologi Kayu Tropis Vol 16, No 2 (2018): Jurnal Ilmu dan Teknologi Kayu Tropis
Publisher : Jurnal Ilmu dan Teknologi Kayu Tropis

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (38.454 KB)

Sago waste is a potential biomass that can be used as active charcoal raw material. The objectives of this research were to know the effect of steam duration on quality and characteristics of activated charcoal of sago waste. Carbonization process was carried out at 400 ⁰C for four hours, then activation was carried out at 100 ml bar steam pressure, at a temperature of 800 ⁰C with variations of steam duration 60, 80 and 100 minutes and activation without steam, only heating for 60 minutes. The proximate test used the SNI standard, observed the functional group using Fourier Transform Infrared Spectrophotometer (FTIR) and observed the active charcoal structure using X-ray diffraction (XRD). The results showed that the yield, moisture content, volatile, ash content, fixed carbon, iodine absorption of activated charcoal of sago bark and sago soft core were, respectively, 39.22–84.10%, 4.63–6.39%, 3.03–5.06%, 7.74–33.43%, 61.54–88.63%, 158.60–972.60 mg g-1. XRD analyzes showed that the degree of crystalline activated charcoal of sago bark waste with the highest steam time of 100 minutes (35.98%) compared with the degree of crystalline other activated charcoal is only about 20.57-7.30%. FTIR spectroscopy results from activated charcoal of sago waste also identified nitrogen compounds such as NO2 at wave numbers 1370-1390 cm-1; 1530-1560 cm-1; 1620-1660 cm-1 and phosphorus compounds such as P-S at 200-500 cm-1 wave number; P=S at the wave number 500-850 cm-1.Keywords: carbonization, active charcoal, sago, steam

Perbandingan Sifat Bahan Baku dan Pulp Kraft Geronggang (Cratoxylon arborescen) Alam dan Tanaman (Comparison the Properties of Raw Material and Kraft Pulp from Nature and Plantation of Geronggang Wood (Cratoxylon arborescen)) Aprinis, Yeny; Akbar, Opik T; Rizqiani, Kanti D
Jurnal Ilmu dan Teknologi Kayu Tropis Vol 16, No 2 (2018): Jurnal Ilmu dan Teknologi Kayu Tropis
Publisher : Jurnal Ilmu dan Teknologi Kayu Tropis

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (38.454 KB)

Geronggang (Cratoxylum arborescen) is one of local wood in Riau peatlands has potential as raw material for pulp. This study aims to compare properties of raw material and kraft pulp from nature and plantation of geronggang wood. The parameters observed were chemical properties, fibers dimension, and pulp properties. The comparison of the both geronggang properties were analyzed using T test. The results indicated that both geronggang wood nature and plantation showed similar chemical properties in term of extractives, cellulose, and hemicellulose, and fiber dimensions except lignin content. Kraft properties of both geronggang woods also have similar results of yield and Kappa number, except lignin content.Keywords: chemical properties, geronggang, nature, plantation, pulp properties

Physical-Mechanical Properties and Bonding Mechanism of Corn Stalks Particleboard with Citric Acid Adhesive Prasetiyo, Kurnia Wiji; Oktaviani, Linda; Astari, Lilik; Syamani, Firda A; Subyakto, Subyakto; Achmadi, Suminar S
Jurnal Ilmu dan Teknologi Kayu Tropis Vol 16, No 2 (2018): Jurnal Ilmu dan Teknologi Kayu Tropis
Publisher : Jurnal Ilmu dan Teknologi Kayu Tropis

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (38.454 KB)

As a natural fiber and agricultural by-product, corn stalks (Zea mays saccharata) is considered as an alternative raw material to produce particleboard. Corn stalks is a good source of lignocelluloses, renewable and low cost. This research was aimed to investigate the characteristics of corn stalk particleboard with citric acid as adhesive. This study also evaluated bonding mechanism particle with citric acid and the bonds between celluloses derived corn stalk with citric acid. The boards were manufactured under the hot pressing temperature 200 oC for 10 min. The citric acid concentration was varied in 0, 15, 20 and 25 wt%. The board size and target density were (25 x 25 x 0.9) mm3 and 0.8 g.cm-3. Results showed that the physical properties of particleboards improved with increasing citric acid concentration up to 20 wt%. At the optimum citric acid content of 20 wt% could provide particleboards with the modulus of rupture, modulus of elasticity and internal bonding satisfied the requirement of the 13 type of the JIS A 5908 (2003) standard. Infrared (IR) spectral analysis from board which manufactured from isolated cellulose was mixed citric acid and pressed on temperature 200 oC showed the presence of ester linkages that the carboxyl and hydroxyl groups of citric acid had reacted with the hydroxyl groups of corn stalk cellulose.Keywords : citric acid, corn stalk, concentration, particleboard, adhesive

Natural Resistance of Rattan Species from Sumatra Against Subterranean Termite and Its Relation to Chemical Properties (Ketahanan Alami Rotan Asal Sumatra terhadap Rayap Tanah dan Hubungannya dengan Sifat Kimia) Arsyad, Waode OM; Efiyanti, Lisna; Kalima, Titi
Jurnal Ilmu dan Teknologi Kayu Tropis Vol 16, No 2 (2018): Jurnal Ilmu dan Teknologi Kayu Tropis
Publisher : Jurnal Ilmu dan Teknologi Kayu Tropis

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (38.454 KB)

The main problem of rattan utilization was the ravages of destructive organisms attack. The objective of this study was to determine the natural resistance of rattan species from Sumatra against subterranean termites and its relation with the chemical characteristics of rattan. All samples were tested for resistance to subterranean termite and its chemical characteristics according to the Indonesian National Standard. Observations, percentage weight loss, termite survival and degree of attack were determined. Results showed that Calamus insignis, C. holttumii, Daemonorps verticillaris, and D. longipes included in very resistant (Class I). Korthalsia flagellaris, C. zonatus, C. laevigatus, D. sepals, C. spectatissimus, C. rugosus, and C. oleyanus included in resistance class II. Furthermore, D. micracantha included in the class of moderate resistance (class III). The cellulose content has no significant correlation (P>0.01), and lignin has a significant negative correlation (P<0.01) to the weight loss, termite survival and the degree of attack. Rattan that has resistance class I and II can be utilized as raw material of furniture and crafts, while rattan which have resistance class III require preservation treatment to extend its service life.Keywords: chemical properties, rattan, resistance class, subterranean termite

Aktivitas Antioksidan dan Tabir Surya Ekstrak Daun Gyrinops verstegii (Antioxidant activity and Sunscreen of Gyrinops versteegii Leaf Extract) Wahyuningrum, Maeda; Sari, Rita K; Rafi, Mohamad
Jurnal Ilmu dan Teknologi Kayu Tropis Vol 16, No 2 (2018): Jurnal Ilmu dan Teknologi Kayu Tropis
Publisher : Jurnal Ilmu dan Teknologi Kayu Tropis

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (38.454 KB)

The aim of this study was to determine the yield and phytochemicals, antioxidant activity, and sunscreen of the Gyrinops versteegii leaf extracts. The leaf simplicia was extracted using soxhletation method with multilevel polarities of solvent (n-hexane, ethyl acetate, and metanol). The analysis of phytochemical extracts has been carried out the qualitatively and quantitatively. The antioxidant activity testing was performed in vitro through the effective concentration (EC50) extract in capturing DPPH radicals. Sunscreen activity has been done through testing sun protection factor (SPF). The result showed that the yield of n-hexane extract, ethyl acetate, and methanol extracts were 7.83, 5.46, and 6.77% respectively. The phytochemical analysis showed that the ethyl acetate and methanol extracts were strongly detected containing antioxidant compounds such as p-hydroquinone, flavonoid, and tannins with the total phenol of the ethyl acetate and methanol extracts were 3.40 and 4.27% respectively. The n-hexane extract detected contains weakly the antioxidant compounds with the total phenol was 0.45%. The methanol extract is the highest antioxidant activity (EC50 14.46 μg ml-1) and has ultra sunscreen activity (SPF>15).Keywords: antioxidant, extractive, G. versteegii, sunscreen

Evaluasi terhadap Stimulan Ethephon dalam Penyadapan Pinus merkusii (Evaluation on Ethephon Stimulant to Pinus merkusii Tapping) Lukmandaru, Ganis; Sunarta, Sigit; Listyanto, Tomy; Kasmudjo, Kasmudjo; Pujiarti, Rini; Widyorini, Ragil
Jurnal Ilmu dan Teknologi Kayu Tropis Vol 16, No 2 (2018): Jurnal Ilmu dan Teknologi Kayu Tropis
Publisher : Jurnal Ilmu dan Teknologi Kayu Tropis

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (38.454 KB)

The aim of this study was to find out the effect of Ethephon, an ethylene releasing compound, in a combination with sulfuric acid resin production Pinus merkusii. The tested stimulants were ETRAT; SR4; 20% sulfuric acid; 20% sulfuric acid - Ethephon 2%; 3.3% sulfuric acid – 4.1% Ethephon; and sulfuric acid – 8.3% Ethephon. Trees without stimulant spraying were the controls. The results showed that for daily production, the first-day observation gave the highest value but decreased drastically after second-day observation in a varied degree depent on the stimulants. On the basis of accumulated production, the addition of Ethephon in a high or low level of sulfuric acid concentration exhibited significantly higher resin production compared to that of ETRAT; SR4; and 20% sulfuric acid stimulants as well as control trees. It increased resin production by 98.0-150.6% compared to control trees in class age of VII and increased by 140.9-227.1% in class age of IV stands. Moderate significant correlations (r=0.65) were observed between the values of resin production and tree diameter (controls) as well as between the values of resin production and tree diameter of trees treated by sulfuric acid stimulants (r=0.65-0.82).Keywords : class age, ethylene, quarre, resin production, tree diameter

Peningkatan Sifat Papan Partikel Sengon dengan Perlakuan Perendaman Air Dingin (Improvement the Propoerties of Particleboard Made from Sengon with Cold Water Immersion Treatment) Marwanto, Marwanto; Maulana, Sena; Maulana, Mohammad I; Wistara, Nyoman J; Nikmatin, Siti; Febrianto, Fauzi
Jurnal Ilmu dan Teknologi Kayu Tropis Vol 16, No 2 (2018): Jurnal Ilmu dan Teknologi Kayu Tropis
Publisher : Jurnal Ilmu dan Teknologi Kayu Tropis

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (38.454 KB)

The objectives of this research is to evaluate the physical and mechanical properties of particle board made from sengon and mangium woods treated with cold water immersion. Particles of sengon and mangium immersed in cold water for 24 hours. The particles of sengon and mangium are combined with a ratio of 100: 0; 0: 100; 75:25; and 50:50. Particle boards are made in size (30x30x0,9) cm3 with target densities of 0.7 g cm-3. The particle board was binded with methylene diphenyl diisocyanate (MDI) adhesive at 10% content and hot press at 140 °C with 25 kgf cm-2 for 7 minutes. The physical and mechanical properties of particle board are evaluated according to JIS A 5908-2003 standard. The physical and mechanical properties of particle board were much affected by particle combination and cold water immersion treatment. The physical (i.e density, moisture content, water absorption (WA), and thickness swelling (TS)) and mechanical properties (ie. modulus of elasticity (MOE), modulus of rupture (MOR), and internal bonding (IB)) were evaluated. The results showed that cold water immersion improved dimensional stability (WA and TS) of particle board obtained. However, some mechanical properties decreased.Keyword: cold water immersion, mangium, particleboard, sengon

Perubahan Kadar Komponen Kimia pada Tiga Jenis Bambu Akibat Proses Steam dan Pembilasan (Chemical Components Changed in Three Bamboo Species Treated by Steaming and Washing Processes) Murda, Rio A; Nawawi, Deded S; Maulana, Sena; Maulana, Muhammad I; Park, Se-Hwi; Febrianto, Fauzi
Jurnal Ilmu dan Teknologi Kayu Tropis Vol 16, No 2 (2018): Jurnal Ilmu dan Teknologi Kayu Tropis
Publisher : Jurnal Ilmu dan Teknologi Kayu Tropis

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (38.454 KB)

Bamboo has good prospects for composite raw materials such as for Oriented Strand Board (OSB) product. Previous research has shown that steam and rinsing with water and 1% NaOH solution treatments of strand improved the properties of OSB, which might be caused by changing in the chemical components content of bamboo. This study aimed to determine the chemical components content change of sembilang bamboo (Dendrocalamus giganteus Munro), black bamboo (Gigantochloa nigrocillata Kurz.), and tali bamboo (G. apus (Bl.ex Schult.f.)) due to steam and rinsing treatment. The chemical components of bamboo were analyzed referring to the Technical Association of the Pulp and Paper Industry standards (TAPPI). The results showed that the most significant changes in the chemical components content of bamboo occured for holocellulose, hemicellulose, extractive contents, and pH values. The decreasing of hemicellulose, extractive contents, and increasing pH values due to the steam and 1% NaOH rinsing treatment may improve the adhesion quality of OSB.Keywords: bamboo, chemical components, steam modification, strand,

Keragaman Genetik Pertumbuhan dan Hubungannya dengan Penetrasi Pilodyn pada Uji Provenansi-Keturunan Jabon (Neolamarkcia cadamba (Roxb) Bosser) di Parung Panjang, Bogor) (Genetic Variation of Growth and Its Relationship with Pilodyn Penetration on Provenance-Progeny Trial of Jabon (Neolamarkcia cadamba (Roxb) Bosser) at Parung Panjang, Bogor) Anna, Nelly; Siregar, Iskandar Z; Supriyanto, Supriyanto; Karlinasari, Lina; Sudrajat, Dede J
Jurnal Ilmu dan Teknologi Kayu Tropis Vol 16, No 2 (2018): Jurnal Ilmu dan Teknologi Kayu Tropis
Publisher : Jurnal Ilmu dan Teknologi Kayu Tropis

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (38.454 KB)

Jabon (Neolamarkcia cadamba (Roxb) Bosser) is a fast growing and preferred species as material for various wood industries. However, the growth and quality information of its wood is still limited. This study aims to assess the characteristics of growth, physical properties of wood, genetic parameters of growth and physical properties of wood, and its relationship with pilodyn penetration on provenance-progeny trial of jabon in Parung Panjang, Bogor. Measurement of growth characteristics was performed on height and diameter at breadst height (DBH), whereas the physical properties of wood (density, specific gravity, and moisture content) were performed using core samples (destructive methods) and density estimation with pilodyn (nondestructive method). Statistical analysis explains that there are significant differences between provenances in height, diameter, pilodyn penetration, density, and specific gravity, except for moisture content. The mean of plant survival percentage of 36 months old jabon was 52.8%. The relationship between growth character and the physical properties of wood with pilodyn penetration is negative and weak, except in moisture content, positive but weak. The estimation of individual heritability value ranges from 0.011 to 0.183, while heritability of the family ranges from 0.017 to 0.308.Keywords: growth, heritability, jabon, physical properties, pilodyn penetration

Evaluasi terhadap Stimulan Ethephon dalam Penyadapan Pinus merkusii (Evaluation on Ethephon Stimulant to Pinus merkusii Tapping) Ganis Lukmandaru; Sigit Sunarta; Tomy Listyanto; Kasmudjo Kasmudjo; Rini Pujiarti; Ragil Widyorini
Jurnal Ilmu dan Teknologi Kayu Tropis Vol 16, No 2 (2018): Jurnal Ilmu dan Teknologi Kayu Tropis
Publisher : Masyarakat Peneliti Kayu Indonesia

Page 1 of 2 | Total Record : 18

1 2

Filter by Year

2018 2018

Filter By Issues

All Issue Vol 20, No 1 (2022): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 18, No 1 (2020): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 17, No 2 (2019): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 17, No 1 (2019): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 16, No 2 (2018): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 16, No 2 (2018): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 16, No 1 (2018): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 15, No 2 (2017): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 15, No 1 (2017): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 14, No 2 (2016): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 14, No 1 (2016): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 13, No 2 (2015): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 13, No 1 (2015): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 12, No 2 (2014): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 12, No 2 (2014): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 12, No 1 (2014): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 11, No 2 (2013): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 11, No 1 (2013): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 10, No 2 (2012): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 10, No 1 (2012): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 9, No 2 (2011): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 9, No 2 (2011): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 9, No 1 (2011): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 8, No 2 (2010): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 8, No 2 (2010): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 8, No 1 (2010): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 7, No 2 (2009): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 7, No 1 (2009): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 6, No 2 (2008): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 6, No 1 (2008): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 6, No 1 (2008): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 5, No 2 (2007): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 5, No 1 (2007): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 4, No 2 (2006): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 4, No 1 (2006): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 3, No 2 (2005): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 3, No 1 (2005): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 2, No 2 (2004): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 2, No 1 (2004): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 2, No 1 (2004): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 1, No 1 (2003): Jurnal Ilmu dan Teknologi Kayu Tropis Vol 1, No 1 (2003): Jurnal Ilmu dan Teknologi Kayu Tropis More Issue

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
Unknown,

Unknown

INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name -

Contact Email -

Phone -

Journal Mail Official -

Editorial Address -

Location Unknown, Unknown INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
Unknown,

Unknown

INDONESIA